Read this first
Type A (Some Models)
The aerial is embedded into the window glass.
When washing the inside of the window which has an aerial, use a soft cloth dampened in lukewarm water, gently wiping the aerial lines.
Use of glass cleaning products could damage the aerial.
Operating Tips for Audio System
Always adjust the audio while the vehicle is stopped:
Do not adjust the audio control switches while driving the vehicle. Adjusting the audio while driving the vehicle is dangerous as it could distract your attention from the vehicle operation which could lead to a serious accident.
Even if the audio control switches are equipped on the steering wheel, learn to use the switches without looking down at them so that you can keep your maximum attention on the road while driving the vehicle.
For the purposes of safe driving, adjust the audio volume to a level that allows you to hear sounds outside of the vehicle including car horns and particularly emergency vehicle sirens.
-
To prevent the battery from being discharged, do not leave the audio system on for a long period of time when the engine is not running.
-
If a cellular phone or CB radio is used in or near the vehicle, it could cause noise to occur from the audio system, however, this does not indicate that the system has been damaged.
Do not spill any liquid on the audio system.
Do not insert any objects, other than CDs, into the slot.
Radio Reception
AM characteristics
AM signals bend around such things as buildings or mountains and bounce off the ionosphere.
Therefore, they can reach longer distances than FM signals.
Because of this, two stations may sometimes be picked up on the same frequency at the same time.
FM characteristics
An FM broadcast range is usually about 40―50 km (25―30 miles) from the source. Because of extra coding needed to break the sound into two channels, stereo FM has even less range than monaural (non-stereo) FM.
Signals from an FM transmitter are similar to beams of light because they do not bend around corners, but they do reflect. Unlike AM signals, FM signals cannot travel beyond the horizon. Therefore, FM stations cannot be received at the great distances possible with AM reception.
Atmospheric conditions can also affect FM reception. High humidity will cause poor reception. However, cloudy days may provide better reception than clear days.
Multipath noise
Since FM signals can be reflected by obstructions, it is possible to receive both the direct signal and the reflected signal at the same time. This causes a slight delay in reception and may be heard as a broken sound or a distortion. This problem may also be encountered when in close proximity to the transmitter.
Flutter/Skip noise
Signals from an FM transmitter move in straight lines and become weak in valleys between tall buildings, mountains, and other obstacles. When a vehicle passes through such an area, the reception conditions may change suddenly, resulting in annoying noise.
Weak signal noise
In suburban areas, broadcast signals become weak because of distance from the transmitter. Reception in such fringe areas is characterised by sound breakup.
Strong signal noise
This occurs very close to a transmitter tower. The broadcast signals are extremely strong, so the result is noise and sound breakup at the radio receiver.
Station drift noise
When a vehicle reaches the area of two strong stations broadcasting at similar frequencies, the original station may be temporarily lost and the second station picked up. At this time there will be some noise from this disturbance.
Operating Tips for CD Player
Condensation phenomenon
Immediately after turning on the heater when the vehicle is cold, the CD or optical components (prism and lens) in the CD player may become clouded with condensation. At this time, the CD will eject immediately when placed in the unit. A clouded CD can be corrected simply by wiping it with a soft cloth. Clouded optical components will clear naturally in about an hour. Wait for normal operation to return before attempting to use the unit.
Handling the CD player
The following precautions should be observed.
-
Do not use deformed or cracked CDs. The disc may not eject resulting in a malfunction.
-
Do not use non-conventional discs such as heart-shaped, octagonal discs, etc. The disc may not eject resulting in a malfunction.
-
If the memory portion of the CD is transparent or translucent, do not use the disc.
-
A new CD may have rough edges on its inner and outer perimeters. If a disc with rough edges is used, proper setting will not be possible and the CD player will not play the CD. In addition, the disc may not eject resulting in a malfunction. Remove the rough edges in advance by using a ball-point pen or pencil as shown below. To remove the rough edges, rub the side of the pen or pencil against the inner and outer perimeter of the CD.
-
When driving over uneven surfaces, the sound may jump.
-
CDs bearing the logo shown in the illustration can be played. No other discs can be played.
-
Use discs that have been legitimately produced. If illegally-copied discs such as pirated discs are used, the system may not operate properly.
-
Be sure never to touch the signal surface when handling the CDs. Pick up a CD by grasping the outer edge or the edge of the hole and the outer edge.
-
Do not stick paper or tape on the CD. Avoid scratching the reverse side (the side without a label). The disc may not eject resulting in a malfunction.
-
Dust, finger smudges, and dirt can decrease the amount of light reflected from the signal surface, thus affecting sound quality. If the CD should become soiled, gently wipe it with a soft cloth from the centre of the CD to the edge.
-
Do not use record sprays, antistatic agents, or household spray cleaners. Volatile chemicals such as benzine and thinner can also damage the surface of the CD and must not be used. Anything that can damage, warp, or fog plastic should never be used to clean CDs.
-
The CD player ejects the CD if the CD is inserted upside down. Also dirty and/or defective CDs may be ejected.
-
Do not insert cleaning discs in the CD player.
-
Do not insert any disc with a peel-off seal affixed to it.
-
This unit may not be able to play certain CD-R/CD-RWs made using a computer or music CD recorder due to disc characteristics, scratches, smudges, dirt, etc., or due to dust or condensation on the lens inside the unit.
-
Storing CDs in the vehicle exposed to direct sunlight or high temperature may damage the CD-R/CD-RWs, and make them unplayable.
-
CD-R/CD-RW exceeding 700 MB cannot be played.
-
This unit may not be able to play certain discs made using a computer due to the application (writing software) setting used. (For details, consult the store where the application was purchased.)
-
It is possible that certain text data, such as titles, recorded on a CD-R/CD-RW may not be displayed when musical data (CD-DA) is playing.
-
The period from when a CD-RW is inserted to when it begins playing is longer than a normal CD or CD-R.
-
Completely read the instruction manual and cautions for CD-R/CD-RWs.
-
Do not use discs with cellophane tape adhering, partially peeled off labels, or adhesive material exuding from the edges of the CD label. Also, do not use discs with a commercially-available CD-R label affixed. The disc may not eject resulting in a malfunction.
Operating Tips for MP3
MP3 stands for MPEG Audio Layer 3, which is standardised voice compression established by the ISO*1 working group (MPEG).
Use of MP3 allows for audio data to be compressed to approximately a tenth of the source data size.
This unit plays files with the extension (.mp3) as MP3 files.
-
International Organisation for Standardisation
Do not use an audio file extension on files other than audio files. In addition, do not change the audio file extension. Otherwise, the unit will not recognise the file correctly resulting in noise or a malfunction.
Supply of this product only conveys a license for private, non-commercial use and does not convey a license nor imply any right to use this product in any commercial (i.e. revenue-generating) real time broadcasting (terrestrial, satellite, lead and/or any other media), broadcasting/streaming via the Internet, intranets and/or other networks or in other electronic content distribution systems, such as pay-audio or audio-on-demand applications. An independent license for such use is required. For details, please visit http://www.mp3licensing.com.
-
This audio system handles MP3 files that have been recorded on CD-R/CD-RW/CD-ROMs.
-
When naming an MP3 file, be sure to add an MP3 file extension (.mp3) after the file name.
-
The number of characters which can be displayed is restricted.
Operating Tips for AAC
AAC stands for Advanced Audio Coding, which is standardised voice compression established by the ISO*1 working group (MPEG). Audio data can be created and stored at a higher compression ratio than MP3.
This unit plays files with the extensions (.aac/.m4a/.wav*2) as the AAC files.
-
International Organisation for Standardisation
-
Type C/Type D
Do not use an audio file extension on files other than audio files. In addition, do not change the audio file extension. Otherwise, the unit will not recognise the file correctly resulting in noise or a malfunction.
-
AAC files written under specifications other than the indicated specification may not play normally or files or folder names may not display correctly.
-
The file extension may not be provided depending on the computer operating system, version, software, or settings. In this case, add the file extension “.aac ”, “.m4a”, or “.wav*2” to the end of the file name, and then write it to the memory.
*2 Type C/Type D
Operating Tips for OGG
OGG is the audio compression format for Xiph. Org Foundation.
Audio data can be created and stored at a higher compression ratio than MP3.
This unit plays files with the extension (.ogg) as OGG files.
Do not use an audio file extension on files other than audio files. In addition, do not change the audio file extension. Otherwise, the unit will not recognise the file correctly resulting in noise or a malfunction.
-
OGG files written under specifications other than the indicated specification may not play normally or files or folder names may not display correctly.
-
The file extension may not be provided depending on the computer operating system, version, software, or settings. In this case, add the file extension “.ogg” to the end of the file name, and then write it to the disc.
Operating Tips for iPod
This unit supports playback of music files recorded to an iPod.
-
iPod is a trademark of Apple Inc., registered in the U.S. and other countries.
The iPod may not be compatible depending on the model or OS version. In this case, an error message is displayed.
-
Remove the iPod when it is not in use. Because the iPod is not designed to withstand excessive changes in temperature inside the cabin, it could be damaged or the battery may deteriorate due to the excessive temperature or humidity inside the cabin if it is left in the vehicle.
-
If data in the iPod is lost while it is connected to the unit, Mazda cannot guarantee recovery of any lost data.
-
If the iPod battery is deteriorated, the iPod may not recharge and playback may not be possible when it is connected to the unit.
-
For details on using the iPod, refer to the iPod instruction manual.
-
When connecting the iPod to a USB port, all commands are made from the audio unit. iPod control is not possible.
The audio unit cannot display images or videos stored in an iPod.
Audio Set [Type A/Type B (non-touchscreen)]
Power/Volume/Sound Controls
Power ON/OFF
Switch the ignition to ACC or ON. Press the power/volume dial to turn the audio system on. Press the power/volume dial again to turn the audio system off.
Volume adjustment
To adjust the volume, turn the power/volume dial. Turn the power/volume dial clockwise to increase volume, anticlockwise to decrease it.
Audio sound adjustment
-
Press the menu button (
) to select the function. The selected function will be indicated.
-
Turn the audio control dial to adjust the selected functions as follows:
|
Indication |
Setting value |
|
|---|---|---|
|
Turn Anticlockwise |
Turn Clockwise |
|
|
AF*1 (Setting Alternative Frequency (AF)) |
Off |
On |
|
REG*1 (Setting Regional Programme (REG)) |
Off |
On |
|
ALC (Automatic volume adjustment) |
Level decrease |
Level increase |
|
BASS (Low pitch sound) |
Decrease bass |
Increase bass |
|
TREB (Treble sound) |
Decrease treble |
Increase treble |
|
FADE (Front/back volume balance) |
Shift the sound to the front |
Shift the sound to the rear |
|
BAL (Left/right volume balance) |
Shift the sound to the left |
Shift the sound to the right |
|
BEEP (Audio operation sound) |
Off |
On |
|
BT SETUP*2 |
Select mode |
|
|
12Hr (12 Hr/24 Hr time adjustment) |
12Hr (Flashing) |
24Hr (Flashing) |
24Hr
*1 Type B
*2 Depending on the model, this function may not be available.
If not operated for several seconds, the display returns to the previous display.
To reset bass, treble, fade, and balance, press the menu button () for 2 seconds. The unit will beep and “CLEAR” will be displayed.
AF (Setting Alternative Frequency (AF)) (Type B)
The AF function of the Radio Data System (RDS) can be set on or off.
Refer to Operating the Radio (Type B) (Search).
REG (Setting Regional Programme (REG)) (Type B)
The REG function of the Radio Data System (RDS) can be set on or off.
Refer to Operating the Radio (Type B) (Search).
ALC (Automatic volume adjustment)
The automatic level control (ALC) changes the audio volume automatically according to the vehicle speed. The faster the vehicle speed, the higher the volume increases. ALC has ALC OFF and ALC LEVEL 1 to 7 modes. At ALC LEVEL 7, the amount that the volume can increase is at the maximum. Select the mode according to the driving conditions.
BEEP (Audio operation sound)
The setting for the operation sound when pressing and holding a button can be changed. The initial setting is ON. Set to OFF to mute the operation sound.
BT SETUP mode (Some Models)
Music and other audio such as voice data recorded on portable audio devices and mobile phones available on the market which are equipped with the Bluetooth® transmission function can be listened to via wireless transmission over the vehicle's speakers. Using the BT SETUP mode, these devices can be programmed to the Bluetooth® unit or changed (Search).
12Hr 
24Hr (12 Hr/24 Hr time adjustment)
Rotating the audio control dial switches the display between 12 and 24-hour clock time (Search).
Clock
Setting the time
The clock can be set at any time when the ignition is switched to ACC or ON.
-
To adjust the time, press the clock button (
) for about 2 seconds until a beep is heard.
-
The clock's current time will flash.
Time adjustment
-
To adjust the time, press the hour/minute set button (
, 
) while the clock's current time is flashing.
-
The hours advance while the hour set button (
) is pressed. The minutes advance while the minute set button () is pressed.
-
-
Press the clock button (
) again to start the clock.
Time resetting
-
Press the clock button (
) for about 2 seconds until a beep is heard.
-
Press the :00 button (1).
-
When the button is pressed, the time will be reset as follows:
(Example)
12:01―12:29→12:00
12:30―12:59→1:00
-
When the :00 button (1) is pressed, the seconds will start at “00”.
-
Switching between 12 and 24-hour clock time:
Press the menu button (
) several times until 12 and 24-hour clock time are displayed. Turn the audio control
dial in either direction, select the desired clock setting while the preferred clock
time is flashing.
Operating the Radio (Type A)
Radio ON
Press a band selector button () to turn the radio on.
Band selection
Successively pressing the band selector button () switches the bands as follows: FM1→FM2→AM.
The selected mode will be indicated.
If the FM broadcast signal becomes weak, reception automatically changes from STEREO to MONO for reduced noise.
Tuning
The radio has the following tuning methods: Manual, Seek, Scan, Preset channel, and Auto memory tuning. The easiest way to tune stations is to set them on preset channels.
Manual tuning
Select the station by pressing the tuning button (, ) lightly.
Seek tuning
Automatic search for radio stations starts when the tuning button (, ) is pressed until a beep sound is heard. The search stops when a station is found.
If you continue to press and hold the button, the frequency will continue changing without stopping.
Scan tuning
Press and hold the scan button (
) to automatically sample strong stations. Scanning stops at each station for about
5 seconds. To hold a station, press and hold the scan button () again during this interval.
Preset channel tuning
The 6 preset channels can be used to store 6 AM and 12 FM stations.
-
To set a channel first select AM, FM1, or FM2. Tune to the desired station.
-
Press a channel preset button for about 2 seconds until a beep is heard. The preset channel number or station frequency will be displayed. The station is now held in the memory.
-
Repeat this operation for the other stations and bands you want to store. To tune one in the memory, select AM, FM1, or FM2 and then press its channel preset button. The station frequency or the channel number will be displayed.
Auto memory tuning
This is especially useful when driving in an area where the local stations are not known.
Press and hold the auto memory button (
) for about 2 seconds until a beep is heard; the system will automatically scan and
temporarily store up to 6 stations with the strongest frequencies in each selected
band in that area.
After scanning is completed, the station with the strongest frequency will be tuned
and its frequency displayed. Press and release the auto memory button () to recall stations from the auto-stored stations. One stored station will be selected
each time and its frequency and channel number will be displayed.
If no stations can be tuned after scanning operations, “A” will be displayed.
Operating the Radio (Type B)
Radio ON
Press a band selector button () to turn the radio on.
Band selection
Successively pressing the band selector button () switches the bands as follows: FM1→FM2→MW/LW.
The selected mode will be indicated.
If the FM broadcast signal becomes weak, reception automatically changes from STEREO to MONO for reduced noise.
Tuning
The radio has the following tuning methods: Manual, Seek, Scan, Preset channel, and Auto memory tuning. The easiest way to tune stations is to set them on preset channels.
Manual tuning
Select the station by pressing the tuning button (, ) lightly.
Seek tuning
Automatic search for radio stations starts when the tuning button (, ) is pressed until a beep sound is heard. The search stops when a station is found.
If you continue to press and hold the button, the frequency will continue changing without stopping.
Scan tuning
Press and hold the scan button () to automatically sample strong stations. Scanning stops at each station for about
5 seconds. To hold a station, press and hold the scan button () again during this interval.
Preset channel tuning
The 6 preset channels can be used to store 6 MW/LW and 12 FM stations.
-
To set a channel first select MW/LW, FM1, or FM2. Tune to the desired station.
-
Press a channel preset button for about 2 seconds until a beep is heard. The preset channel number or station frequency will be displayed. The station is now held in the memory.
-
Repeat this operation for the other stations and bands you want to store. To tune one in the memory, select MW/LW, FM1, or FM2 and then press its channel preset button. The station frequency or the channel number will be displayed.
Radio Data System (RDS)
The radio data system (RDS) does not function if it is out of the system's service coverage area.
Alternative frequency (AF)
AF functions on FM stations. Press the menu button () and select the AF mode to turn it on and “AF” will be displayed. If the radio reception of the current station weakens, the system
switches to an alternative station automatically.
If you wish to continue a regional programme, press the menu button () and select the REG mode to turn it on. “REG ON” is displayed. To cancel it, press the audio control dial and select the REG mode
to turn it off. “REG OFF” is displayed.
Traffic announcement (TA)
If the traffic announcement button (
) is pressed, the unit switches to TA mode and “TA” is displayed.
If a TA broadcast is received while in the TA mode, the TA broadcast intercedes even while using other functions (FM, CD, USB, iPod, AUX, or BT audio), and “Traffic Info” is displayed.
During a TA broadcast, press the traffic announcement button () to end the broadcast and return to the previous mode.
Programme-type information (PTY)
Some FM stations transmit programme-type codes. This code enables alternative stations transmitting the same programme-type code to be found quickly.
Press the programme-type information button (
,
) while in FM mode. The programme-type code and “PTY” will be displayed during reception. If there is no programme-type code, “None” will be displayed.
(To choose a programme type:)
-
Press the Programme-type information button (
,) when the programme-type code is displayed.
-
Operate any one of the following:
-
Press the pre-programmed channel preset button (1 to 6).
-
Press the Programme-type information button (
,).
-
(To scan for programme-type information:)
-
Press the Programme-type information button (
,) when the programme-type code is displayed.
-
Press the Programme-type information button (
,) until the beep sounds.
The unit will scan for broadcasts, if none are found, “Nothing” will be displayed and the unit will return to the previously tuned band.
(To store programme types in the channel preset buttons:)
-
Press the Programme-type information button (
,) when the programme-type code is displayed.
-
Press the Programme-type information button (
,) and select the programme type.
-
While the programme type is displayed, press a channel preset button for about 2 seconds.
Emergency broadcast
If an emergency broadcast is received, the emergency broadcast intercedes even while using other functions (FM, CD, USB, iPod, AUX, or BT audio), and “Alarm!” is displayed.
When the emergency broadcast ends, the system will return to the previous mode.