The speedometer indicates the speed of the vehicle.
(Analog speedometer type)
If a few seconds have elapsed after switching the ignition off, the needle may deviate. However, this does not indicate a problem.
The display mode can be changed from odometer to trip meter A to trip meter B and then back to odometer by pressing the selector while one of them is displayed. The selected mode will be displayed.
When the ignition is switched to ACC or off, the odometer or trip meters cannot be displayed, however, pressing the selector can inadvertently switch the trip meters or reset them during an approximate ten-minute period in the following cases:
After the ignition is switched to off from ON.
After the driver's door is opened.
Odometer
The odometer records the total distance the vehicle has been driven.
Trip meter
The trip meter can record the total distance of two trips. One is recorded in trip meter A, and the other is recorded in trip meter B.
For instance, trip meter A can record the distance from the point of origin, and trip meter B can record the distance from where the fuel tank is filled.
When trip meter A is selected, pressing the selector again within one second will change to trip meter B mode.
When trip meter A is selected, TRIP A will be displayed. When trip meter B is selected, TRIP B will be displayed.
The trip meter records the total distance the vehicle is driven until the meter is again reset. Return it to “0.0” by depressing and holding the selector for one second or more. Use this meter to measure trip distances and to compute fuel consumption.
(Vehicles with type B audio)
If the fuel economy data is reset using the fuel economy monitor, or trip A is reset using the trip meter when the function which synchronizes the fuel economy monitor and the trip meter is on, the fuel economy data and trip A are reset simultaneously.
Refer to Fuel Economy Monitor (Search).
Only the trip meters record tenths of kilometres (miles).
The trip record will be erased when:
The power supply is interrupted (blown fuse or the battery is disconnected).
The vehicle is driven over 9999.9 km (mile).
The tachometer shows engine speed in thousands of revolutions per minute (rpm).
Do not run the engine with the tachometer needle in the RED ZONE.
This may cause severe engine damage.
Type A
Type B
When the tachometer needle enters the STRIPED ZONE, this indicates to the driver that the gears should be shifted before entering the RED ZONE.
The fuel gauge shows approximately how much fuel is remaining in the tank when the ignition is switched ON. We recommend keeping the tank over 1/4 full.
If the low fuel warning light illuminates or the fuel level is very low, refuel as soon as possible.
Refer to Warning/Indicator Lights (Search).
After refuelling, it may require some time for the indicator to stabilize. In addition, the indicator may deviate while driving on a slope or curve since the fuel moves in the tank.
The display indicating a quarter or less remaining fuel has more segments to show the remaining fuel level in greater detail.
The direction of the arrow () indicates that the fuel-filler flap is on the left side of the vehicle.
(SKYACTIV-D 1.5)
If inconsistency in engine performance or stalling occurs due to low fuel level conditions, refuel the vehicle as soon as possible and add at least 10 L (2.7 US gal, 2.2 Imp gal) of fuel.
When the position lights are turned on with the ignition switched ON, the brightness of the instrument panel illumination is dimmed.
When the position lights are turned on, the position lights indicator light in the instrument cluster turns on.
Refer to Headlights (Search).
The brightness of the instrument panel and instrument panel illuminations can be adjusted by rotating the knob.
The brightness decreases by rotating the knob to the left. A beep sound will be heard when the knob has been rotated to the maximum dim position.
The brightness increases by rotating the knob to the right.
Function for cancelling illumination dimmer
The illumination dimmer can be cancelled by rotating the instrument panel illumination knob to the right until a beep sound is heard while the instrument cluster is dimmed with the ignition switched ON. If the instrument cluster's visibility is reduced due to glare from surrounding brightness, cancel the illumination dimmer.
When the illumination dimmer is cancelled, the instrument cluster cannot be dimmed even if the position lights are turned on.
When the illumination dimmer is cancelled, the screen in the centre display switches to constant display of the daytime screen.
Instrument Cluster varies depending on model and specifications.
These lights turn on or flash to notify the user of the system operation status or a system malfunction.
Signal |
Warning Lights |
Page |
---|---|---|
![]() |
Master Warning Light*1 |
(Search) |
![]() |
Brake System Warning Light*1*2 |
(Search) |
![]() |
ABS Warning Light*1 |
(Search) |
![]() |
Charging System Warning Light*1 |
(Search) |
![]() |
Engine Oil Warning Light*1 |
(Search) |
![]() |
Check Engine Light*1 |
(Search) |
![]() (Red) |
High Engine Coolant Temperature Warning Light*1 |
(Search) |
![]() (Amber) |
i-stop Warning Light*1 |
(Search) |
![]() |
Automatic Transaxle Warning Light*1 (Some Models) |
(Search) |
![]() |
4WD Warning Light*1 (Some Models) |
(Search) |
![]() |
Power Steering Malfunction Indicator Light*1 |
(Search) |
![]() |
Air Bag/Seat Belt Pretensioner System Warning Light*1 |
(Search) |
![]() |
Low Fuel Warning Light |
(Search) |
![]() |
Seat Belt Warning Light (Front seat) |
(Search) |
![]() (Red) |
Seat Belt Warning Light (Rear seat) |
(Search) |
![]() |
Door-Ajar Warning Light |
(Search) |
![]() (Red) |
KEY Warning Light*1 |
(Search) |
![]() (Amber) |
Smart City Brake Support (SCBS) Warning Light (Some Models) |
(Search) |
![]() |
Lane Departure Warning System (LDWS) Warning Light*1 (Some Models) |
Illuminated (Search) |
Flashing (Search) |
||
![]() (Amber) |
High Beam Control System (HBC) Warning Light*1 (Some Models) |
(Search) |
![]() |
LED Headlight Warning Light (Some Models) |
(Search) |
The light turns on when the ignition is switched on for an operation check, and turns off a few seconds later or when the engine is started. If the light does not turn on or remains turned on, have the vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.
The light turns on continuously when the parking brake is applied.
These lights turn on or flash to notify the user of the system operation status or a system malfunction.
Signal |
Indicator Lights |
Page |
---|---|---|
![]() |
Blind Spot Monitoring (BSM) OFF Indicator Light*1 (Some Models) |
(Search) |
![]() |
Lane Departure Warning System (LDWS) OFF Indicator Light*1 (Some Models) |
(Search) |
![]() (Green) |
KEY Indicator Light |
(Search) |
![]() (Green) |
Seat Belt Indicator Light (Rear seat) |
(Search) |
![]() (Green) |
High Beam Control System (HBC) Indicator Light (Some Models) |
(Search) |
![]() |
Glow Indicator Light*1 (Some Models) |
(Search) |
![]() |
Diesel Particulate Filter Indicator Light*1 (Some Models) |
(Search) |
![]() |
Wrench Indicator Light*1 |
(Search) |
![]() |
TCS/DSC Indicator Light*1 (Some Models) |
|
![]() |
TCS OFF Indicator Light*1 (Some Models) |
(Search) |
![]() (Red) |
Smart City Brake Support (SCBS) Indicator Light*1 (Some Models) |
(Search) |
![]() |
Smart City Brake Support (SCBS) OFF Indicator Light*1 (Some Models) |
(Search) |
![]() (Green) |
i-stop Indicator Light |
(Search) |
![]() (Blue) |
Low Engine Coolant Temperature Indicator Light |
(Search) |
![]() |
Shift Position Indication |
(Search) |
![]() |
Headlight High-Beam Indicator Light |
|
![]() |
Direction Indicator/Hazard Warning Indicator Lights |
|
![]() |
Security Indicator Light*1 |
(Search) |
![]() (Amber) |
Cruise Main Indicator Light (Some Models) |
(Search) |
![]() (Green) |
Cruise Set Indicator Light (Some Models) |
(Search) |
![]() |
Select Mode Indicator Light (Some Models) |
(Search) |
![]() |
Lights-On Indicator Light |
(Search) |
![]() |
Fog Light Indicator Light (Some Models) |
(Search) |
The light turns on when the ignition is switched on for an operation check, and turns off a few seconds later or when the engine is started. If the light does not turn on or remains turned on, have the vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.
When the ignition is switched ON, the wrench indicator light is illuminated and then turns off after a few seconds.
The wrench indicator light is illuminated when the preset maintenance period arrives. Verify the content and perform maintenance.
Refer to Maintenance Monitor (Search).
SKYACTIV-D 1.5
The wrench indicator light turns on when the engine oil has deteriorated.
Depending on the vehicle use conditions, the wrench indicator light may turn on for reasons other than the preset maintenance period.
If the wrench indicator light turns on for reasons other than the preset maintenance period, engine oil replacement is recommended.
The light illuminates continuously when the engine coolant temperature is low and turns off after the engine is warm.
If the low engine coolant temperature indicator light remains illuminated after the engine has been sufficiently warmed up, the temperature sensor could have a malfunction. Consult an expert repairer, we recommend an Authorised Mazda Repairer.
This light may illuminate when the ignition is switched ON.
It turns off when the glow plugs are warm. If the ignition is left switched ON for a long period of time without the engine running after the glow plugs are warmed up, the glow plugs may warm up again which will illuminate the glow indicator light.