Routine Service
We highly recommend that these items be inspected daily, or at least every week.
Engine Oil Level (Search)
Engine Coolant Level (Search)
Brake and clutch Fluid Level (Search)
Washer Fluid Level (Search)
Battery Maintenance (Search)
Tyre Inflation Pressure (Search)
Improper or incomplete service may result in problems. This section gives instructions only for items that are easy to perform.
As explained in the Introduction (Search), several procedures can be done only by a qualified service technician with special tools.
Improper do-it yourself maintenance during the warranty period may affect warranty coverage. For details, read the separate Mazda Warranty statement provided with the vehicle. If you are unsure about any servicing or maintenance procedure, have it done by an expert repairer, we recommend an Authorised Mazda Repairer.
There are strict environmental laws regarding the disposal of waste oil and fluids. Please dispose of your waste properly and with due regard to the environment.
We recommend that you entrust the oil and fluid changes of your vehicle to an Authorised Mazda Repairer.
Do not perform maintenance work if you lack sufficient knowledge and experience or the proper tools and equipment to do the work. Have maintenance work done by a qualified technician:
Performing maintenance work on a vehicle is dangerous if not done properly. You can be seriously injured while performing some maintenance procedures.
If you must run the engine while working under the bonnet, make certain that you remove all jewellery (especially rings, bracelets, watches, and necklaces) and all neckties, scarves, and similar loose clothing before getting near the engine or cooling fan which may turn on unexpectedly:
Working under the bonnet with the engine running is dangerous. It becomes even more dangerous when you wear jewellery or loose clothing.
Either can become entangled in moving parts and result in injury.
Pull over to a safe location, then switch the ignition off and make sure the fan is
not running before attempting to work near the cooling fan:
Working near the cooling fan when it is running is dangerous. The fan could continue running indefinitely even if the engine has stopped and the engine compartment temperature is high. You could be hit by the fan and seriously injured.
Do not leave items in the engine compartment:
After you have finished checking or doing servicing in the engine compartment, do not forget and leave items such as tools or rags in the engine compartment.
Tools or other items left in the engine compartment could cause engine damage or a fire leading to an unexpected accident.
Always check that the bonnet is closed and securely locked:
A bonnet that is not closed and securely locked is dangerous as it could fly open while the vehicle is moving and block the driver's vision which could result in a serious accident.
With the vehicle parked, pull the release handle to unlock the bonnet.
Insert your hand into the bonnet opening, slide the latch lever to the right, and lift up the bonnet.
The lever is located a little to the left of centre when facing the vehicle.
Grasp the support rod in the padded area and secure it in the support rod hole indicated by the arrow to hold the bonnet open.
Check under the bonnet area to make certain all filler caps are in place and all loose items (e.g. tools, oil containers, etc.) have been removed.
Lift the bonnet, grasp the padded area on the support rod, and secure the support rod in the clip. Verify that the support rod is secured in the clip before closing the bonnet.
Lower the bonnet slowly to a height of about 20 cm (7.9 in) above its closed position and then let it drop.
When closing the bonnet, do not push it excessively such as by applying your weight. Otherwise, the bonnet could be deformed.
Changing the engine oil should be done by an expert repairer, we recommend an Authorised Mazda Repairer.
In order to keep the maintenance interval (Search) and to protect the engine from damage caused by poor lubrication, it is vitally important to make use of engine oil with the correct specification. Do not use oils which do not meet the below specification or requirements. Use of unsuitable oil may lead to engine damage which is not covered by the Mazda Warranty.
Engine oil viscosity, or thickness, has an effect on fuel economy and cold-weather operation (starting and oil flow).
Low-viscosity engine oils can provide improved fuel economy and cold-weather performance.
(SKYACTIV-G 2.0)
Mazda recommends using Mazda Premium Motor Oil (for Australia) or Mazda Motor Oil (for New Zealand) which has been specifically designed and tested to meet the stringent Mazda Engineering Standards (MES) for your Mazda. To ensure engine longevity is not compromised particularly under the harsh climatic conditions existing in Australia and New Zealand, we only recommend using genuine Mazda engine oil which is available throughout the Mazda Dealer network.
If Mazda Premium Motor Oil (for Australia) or Mazda Motor Oil (for New Zealand) is not selected for use, always use an engine oil meeting the specifications:
Use ILSAC GF-II/GF-III/GF-IV/GF-V, or API service SG or higher.
(SKYACTIV-D 1.5)
Mazda recommends using Mazda Diesel Engine Oil which has been specifically designed and tested to meet the stringent Mazda Engineering Standards (MES) for your Mazda. To ensure engine longevity is not compromised particularly under the harsh climatic conditions existing in Australia and New Zealand, we only recommend using genuine Mazda Diesel Engine Oil which is available throughout the Mazda Dealer network.
If Mazda Diesel Engine Oil is not selected for use, always use an engine oil meeting the specifications:
Use ACEA C1 or JASO DL-1.
When choosing an oil, consider the temperature range your vehicle will operate in before the next oil change.
Then select the recommended viscosity from the chart.
Using oils of viscosity besides those recommended for specific temperature ranges could result in engine damage.
(SKYACTIV-D 1.5)
SKYACTIV-D 1.5 uses specified oil. Please confirm the specification in owner's manual. If engine oil other than the specified oil is used, the Diesel Particulate Filter effective period of use will be shortened or the Diesel Particulate Filter may be damaged.
(SKYACTIV-G 2.0)
It is normal for all engines to consume engine oil under normal driving conditions.
Engine oil consumption may be as high as 0.8 L/1000 km (1 L/800 miles). This may be as a result of evaporation, internal ventilation or burning of the lubricating oil in the working engine. Oil consumption may be higher when the engine is new due to the running-in process. Oil consumption is also dependant on engine speed and engine load. Under extreme driving conditions, oil consumption may be higher.
(SKYACTIV-D 1.5)
Whenever the engine oil is replaced, the vehicles engine control unit needs to be reset as soon as possible. Otherwise the wrench indicator light or engine oil warning light may turn on. To reset the engine control unit, consult an expert repairer, we recommend an Authorised Mazda Repairer or refer to the vehicle engine control unit reset procedure (Search).
Inspect the engine oil level periodically. When inspecting the engine oil, if the engine oil level is exceeds the “X” mark on the dipstick, replace the engine oil. This should be done by an expert repairer, we recommend an Authorised Mazda Repairer. When replacing the engine oil, inspect the oil level using the oil dipstick and refill so that the engine oil level is within the range between MIN and MAX as shown in the figure.
After replacing the engine oil, have a repair shop such as an Authorised Mazda Repairer perform the initialization (engine oil data resetting) of the recorded value. If the value recorded by the computer is not initialized, the wrench indicator light may not turn off or it may turn on earlier than normal.
The initialization (engine oil data resetting) of the recorded value can be performed using the following procedure:
Switch the ignition OFF.
Switch the ignition ON with the selector pressed, and press and hold the selector
for about 5 seconds until the master warning light flashes.
After the master warning light flashes for several seconds, the initialization is completed.
Be sure the vehicle is on a level surface.
Warm up the engine to normal operating temperature.
Turn it off and wait at least 5 minutes for the oil to return to the sump.
Pull out the dipstick, wipe it clean, and reinsert it fully.
SKYACTIV-G 2.0
SKYACTIV-D 1.5
(SKYACTIV-D 1.5)
When inspecting the engine oil level, pull out the dipstick straight without twisting. In addition, when inserting the dipstick, always insert it without twisting so that the “X” mark faces the front of the vehicle.
Pull it out again and examine the level.
The level is normal if it is between the MIN and MAX marks.
If it is near or below MIN, add enough oil to bring the level to MAX.
Do not overfill the engine oil. This may cause engine damage.
Make sure the O-ring on the dipstick is positioned properly before reinserting the dipstick.
Reinsert the dipstick fully.
If the brake/clutch fluid level is low, have the brakes inspected:
A low brake/clutch fluid level is dangerous.
A low level could indicate brake lining wear or a brake system leak which could cause the brakes to fail and lead to an accident.
The brakes and clutch draw fluid from the same reservoir.
Inspect the fluid level in the reservoir regularly. It should be kept between the MAX and MIN lines.
The level normally drops with accumulated distance, a condition associated with wear of brake and clutch linings. If it is excessively low, have the brake/clutch system inspected by an expert repairer, we recommend an Authorised Mazda Repairer.
Use only windscreen washer fluid or plain water in the reservoir:
Using radiator antifreeze as washer fluid is dangerous. If sprayed on the windscreen, it will dirty the windscreen, affect your visibility, and could result in an accident.
Inspect fluid level in the washer fluid reservoir; add fluid if necessary.
Use plain water if washer fluid is unavailable.
But use only washer fluid in cold weather to prevent it from freezing.
Front and rear washer fluid is supplied from the same reservoir.
Hot waxes applied by automatic car washers have been known to affect the wiper's ability to clean windows.
To prevent damage to the wiper blades, do not use petrol, paraffin, paint thinner, or other solvents on or near them.
When the wiper lever is in the AUTO position and the ignition is switched ON, the wipers may move automatically in the following cases:
If the windscreen above the rain sensor is touched.
If the windscreen above the rain sensor is wiped with a cloth.
If the windscreen is struck with a hand or other object.
If the rain sensor is struck with a hand or other object from inside the vehicle.
Be careful not to pinch hands or fingers as it may cause injury, or damage the wipers. When washing or servicing the vehicle, make sure the wiper lever is in the OFF position.
Contamination of either the windscreen or the blades with foreign matter can reduce wiper effectiveness. Common sources are insects, tree sap, and hot wax treatments used by some commercial car washes.
If the blades are not wiping properly, clean the window and blades with a good cleaner or mild detergent; then rinse thoroughly with clean water. Repeat if necessary.
When the wipers no longer clean well, the blades are probably worn or cracked.
Replace them.
To prevent damage to the wiper arms and other components, do not try to sweep the wiper arm by hand.
When raising both windscreen wiper arms, raise the driver's side wiper arm first. When lowering the wiper arms, slowly lower the wiper arm from the passenger's side first while supporting it with your hand. Forcefully lowering the wiper arms could damage the wiper arm and blade, and may scratch or crack the windscreen.
Raise the wiper arm.
Open the clip and slide the blade assembly in the direction of the arrow.
Tilt the blade assembly and remove it from the arm.
To prevent damage to the windscreen let the wiper arm down easily, do not let it slap down on the windscreen.
Pull down the blade rubber and slide it out of blade holder.
Remove the metal stiffeners from each blade rubber and install them in the new blade.
Do not bend or discard the stiffeners. You need to use them again.
If the metal stiffeners are switched, the blade's wiping efficiency could be reduced.
So do not use the driver's side metal stiffeners on the passenger's side, or vice versa.
Be sure to reinstall the metal stiffeners in the new blade rubber so that the curve is the same as it was in the old blade rubber.
Carefully insert the new blade rubber. Then install the blade assembly in the reverse order of removal.
When the wiper no longer cleans well, the blade is probably worn or cracked.
Replace it.
To prevent damage to the wiper arm and other components, do not move the wiper by hand.
Raise the wiper arm and rotate the wiper blade to the right until it unlocks, then remove the blade.
To prevent damage to the rear window, do not let the wiper arm fall on it.
Pull down the blade rubber and slide it out of the blade holder.
Remove the metal stiffeners from the blade rubber and install them in the new blade.
Do not bend or discard the stiffeners. You need to use them again.
Carefully insert the new blade rubber.
Then install the blade assembly in the reverse order of removal.
Headlights (Low beam)
Headlights (High beam)
Position lights
Running lights/Position lights
Fog lights (Some Models)
Front direction indicator lights
Side direction indicator lights
Brake lights/Tail lights
Tail lights (Some Models)
Rear direction indicator lights
Reverse lights
High-mount brake light
Number plate lights
Overhead lights (Front) /Map lights
Overhead lights (Rear)
Luggage compartment light
Never touch the glass portion of a halogen bulb with your bare hands and always wear eye protection when handling or working around the bulbs:
When a halogen bulb breaks, it is dangerous. These bulbs contain pressurised gas. If one is broken, it will explode and serious injuries could be caused by the flying glass.
If the glass portion is touched with bare hands, body oil could cause the bulb to overheat and explode when lit.
Always keep halogen bulbs out of the reach of children:
Playing with a halogen bulb is dangerous. Serious injuries could be caused by dropping a halogen bulb or breaking it some other way.
When removing the lens or lamp unit using a flathead screwdriver, make sure that the flathead screwdriver does not contact the interior terminal. If the flathead screwdriver contacts the terminal, a short circuit may occur.
To replace the bulb, contact an expert repairer, we recommend an Authorised Mazda Repairer.
If the halogen bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used.
Use the protective cover and carton for the replacement bulb to dispose of the old bulb promptly and out of the reach of children.
Headlights (With LED headlights)
The LED bulb cannot be replaced as a single unit because it is an integrated unit.
The LED bulb has to be replaced with the unit. We recommend an Authorised Mazda Repairer when the replacement is necessary.
Headlights (With halogen headlights)
High-beams bulbs
Make sure the ignition is switched off, and the headlight switch is off.
Lift the bonnet.
Disconnect the connector from the unit by pressing the tab on the connector with your finger and pulling the connector downward.
Turn the socket and bulb assembly to remove it. Carefully remove the bulb from its socket in the reflector by gently pulling it straight backward out of the socket.
Install the new bulb in the reverse order of the removal procedure.
Low-beam bulbs
Make sure the ignition is switched off, and the headlight switch is off.
Lift the bonnet.
Disconnect the connector from the unit by pressing the tab on the connector with your finger and pulling the connector downward.
Turn the socket and bulb assembly to remove it. Carefully remove the bulb from its socket in the reflector by gently pulling it straight backward out of the socket.
Install the new bulb in the reverse order of the removal procedure.
Running lights/Position lights (With LED headlights)
The LED bulb cannot be replaced as a single unit because it is an integrated unit.
The LED bulb has to be replaced with the unit. We recommend an Authorised Mazda Repairer when the replacement is necessary.
Position lights (With halogen headlights)
Make sure the ignition is switched off, and the headlight switch is off.
Turn the socket and bulb assembly anticlockwise and remove it.
Disconnect the bulb from the socket.
Install the new bulb in the reverse order of the removal procedure.
Front direction indicator lights
Make sure the ignition is switched off, and the headlight switch is off.
Turn the screw anticlockwise and remove it, and then partially peel back the mudguard.
Turn the socket and bulb assembly anticlockwise and remove it.
Disconnect the bulb from the socket.
Install the new bulb in the reverse order of the removal procedure.
Fog lights (Some Models), Side direction indicator lights, Brake lights/Tail lights (With LED headlights), High-mount brake light, Tail lights (With LED headlights)
The LED bulb cannot be replaced as a single unit because it is an integrated unit.
The LED bulb has to be replaced with the unit. We recommend an Authorised Mazda Repairer when the replacement is necessary.
Rear direction indicator lights, Brake lights/Tail lights (With halogen headlights)
Make sure the ignition is switched off, and the headlight switch is off.
Turn the bolts anticlockwise and remove them.
Pull the unit rearward to remove it.
Turn the socket and bulb assembly anticlockwise and remove it.
Disconnect the bulb from the socket.
Rear direction indicator lights
Brake lights/Tail lights
Install the new bulb in the reverse order of the removal procedure.
Reverse lights
Make sure the ignition is switched off, and the headlight switch is off.
Remove the cover.
Turn the socket and bulb assembly anticlockwise and remove it.
Disconnect the bulb from the socket.
Install the new bulb in the reverse order of the removal procedure.
Number plate lights
Make sure the ignition is switched off, and the headlight switch is off.
Remove the cover.
Turn the socket and bulb assembly anticlockwise and remove it.
Disconnect the bulb from the socket.
Install the new bulb in the reverse order of the removal procedure.
Overhead lights (Front) /Map lights, Overhead lights (Rear)
Wrap a small flathead screwdriver with a soft cloth to prevent damage to the lens, and then remove the lens by carefully prying on the edge of the lens with the flathead screwdriver.
Disconnect the bulb by pulling it out.
Overhead lights (Front) /Map lights
Overhead lights (Rear)
Install the new bulb in the reverse order of the removal procedure.
Luggage compartment light
Wrap a small flathead screwdriver with a soft cloth to prevent damage to the lens and remove the lens unit by carefully prying on the edge of the lens unit with the flathead screwdriver.
Disconnect the bulb by pulling it out.
Install the new bulb in the reverse order of the removal procedure.