Use only windscreen washer fluid or plain water in the reservoir:
Using radiator antifreeze as washer fluid is dangerous. If sprayed on the windscreen, it will dirty the windscreen, affect your visibility, and could result in an accident.
Inspect fluid level in the washer fluid reservoir; add fluid if necessary.
Use plain water if washer fluid is unavailable.
But use only washer fluid in cold weather to prevent it from freezing.
Front and rear washer fluid is supplied from the same reservoir.
Headlights (With LED headlights)
The LED bulb cannot be replaced as a single unit because it is an integrated unit.
The LED bulb has to be replaced with the unit. We recommend an Authorised Mazda Repairer when the replacement is necessary.
Headlights (With halogen headlights)
High-beam bulbs (With running lights)/Running lights (Some Models)
Make sure the ignition is switched off, and the headlight switch is off.
Lift the bonnet.
Turn the cover anticlockwise and remove it.
Turn the socket and bulb assembly anticlockwise and remove it.
Install the new bulb in the reverse order of the removal procedure.
High-beam bulbs (Without running lights)
Make sure the ignition is switched off, and the headlight switch is off.
Lift the bonnet.
Disconnect the connector from the unit by pressing the tab on the connector with your finger and pulling the connector downward.
Turn the socket and bulb assembly to remove it. Carefully remove the bulb from its socket in the reflector by gently pulling it straight backward out of the socket.
Install the new bulb in the reverse order of the removal procedure.
Low-beam bulbs
Make sure the ignition is switched off, and the headlight switch is off.
Lift the bonnet.
Disconnect the connector from the unit by pressing the tab on the connector with your finger and pulling the connector downward.
Turn the socket and bulb assembly to remove it. Carefully remove the bulb from its socket in the reflector by gently pulling it straight backward out of the socket.
Install the new bulb in the reverse order of the removal procedure.
Running lights/Position lights (With LED headlights)
The LED bulb cannot be replaced as a single unit because it is an integrated unit.
The LED bulb has to be replaced with the unit. We recommend an Authorised Mazda Repairer when the replacement is necessary.
Position lights (With halogen headlights)
Make sure the ignition is switched off, and the headlight switch is off.
Turn the socket and bulb assembly anticlockwise and remove it.
Disconnect the bulb from the socket.
Install the new bulb in the reverse order of the removal procedure.
Front direction indicator lights
Make sure the ignition is switched off, and the headlight switch is off.
Turn the screw anticlockwise and remove it, and then partially peel back the mudguard.
Turn the socket and bulb assembly anticlockwise and remove it.
Disconnect the bulb from the socket.
Install the new bulb in the reverse order of the removal procedure.
Side direction indicator lights, High-mount brake light, Front fog lights (Some Models), Tail lights (With LED headlights)
The LED bulb cannot be replaced as a single unit because it is an integrated unit.
The LED bulb has to be replaced with the unit. We recommend an Authorised Mazda Repairer when the replacement is necessary.
Rear direction indicator lights, Brake lights/Tail lights
Make sure the ignition is switched off, and the headlight switch is off.
Turn the bolts anticlockwise and remove them.
Pull the unit rearward to remove it.
Turn the socket and bulb assembly anticlockwise and remove it.
Disconnect the bulb from the socket.
Rear direction indicator lights
Brake lights/Tail lights
(LED type)
The LED bulb cannot be replaced as a single unit because it is an integrated unit.
The LED bulb has to be replaced with the unit. We recommend an Authorised Mazda Repairer when the replacement is necessary.
(Bulb type)
Install the new bulb in the reverse order of the removal procedure.
Reverse lights
Make sure the ignition is switched off, and the headlight switch is off.
Remove the cover.
Turn the socket and bulb assembly anticlockwise and remove it.
Disconnect the bulb from the socket.
Install the new bulb in the reverse order of the removal procedure.
Rear fog light (Some Models)
Make sure the ignition is switched off and the headlight switch is off.
Pull the centre of each plastic retainer and remove the retainers.
Remove the cover.
Turn the socket and bulb assembly anticlockwise and remove it.
Disconnect the bulb from the socket.
Install the new bulb in the reverse order of the removal procedure.
Number plate lights
Make sure the ignition is switched off, and the headlight switch is off.
Remove the cover.
Turn the socket and bulb assembly anticlockwise and remove it.
Disconnect the bulb from the socket.
Install the new bulb in the reverse order of the removal procedure.
Overhead lights (Front) /Map lights, Overhead lights (Rear)
Wrap a small flathead screwdriver with a soft cloth to prevent damage to the lens, and then remove the lens by carefully prying on the edge of the lens with the flathead screwdriver.
Disconnect the bulb by pulling it out.
Overhead lights (Front) /Map lights
Overhead lights (Rear)
Install the new bulb in the reverse order of the removal procedure.
Luggage compartment light
Wrap a small flathead screwdriver with a soft cloth to prevent damage to the lens and remove the lens unit by carefully prying on the edge of the lens unit with the flathead screwdriver.
Disconnect the bulb by pulling it out.
Install the new bulb in the reverse order of the removal procedure.