Instrument Cluster and Display

1. Tachometer
2. Multi-information Display
3. Engine Coolant Temperature Gauge
4. Fuel Gauge
5. Instrument Panel Illumination Switch
6. Speedometer
7. TRIP Switch

The speedometer indicates the speed of the vehicle.

The tachometer shows engine speed in thousands of revolutions per minute (rpm).

 

---

Do not run the engine with the tachometer needle in the RED ZONE.

This may cause severe engine damage.

 

1. STRIPED ZONE^*1

2. RED ZONE^*1

1. The range varies depending on the type of gauge.

Close Caution

View Caution

 

---

When the tachometer needle enters the STRIPED ZONE, this indicates to the driver that the gears should be shifted before entering the RED ZONE.

Close Note

View Note

1. Multi-information Display

2. INFO switch

The multi-information display indicates the following information.

• Speedometer

• Odometer

• Trip meter

• Outside temperature

• Distance-to-empty

• Average fuel economy

• Current fuel economy

• Deceleration Regeneration Charge Display (M Hybrid)

• i-ACTIVSENSE Display

• Vehicle Speed Alarm (Some Models)

• Door-Ajar/Liftgate-Ajar Warning Indication^*1

• Message Display

1. Displayed when opening door/liftgate.

The screen content changes each time the INFO switch is pressed.

1. Basic display

2. Drive information display

3. i-ACTIVSENSE display

4. Message display^*1

1. Displayed only when a warning occurs.

The type of display for the fuel economy and the maximum driving distance can be changed.

Refer to the Settings section in the Mazda Connect Owner's Manual.

You can switch between the odometer and trip meter display using the TRIP switch.

1. TRIP switch

2. Odometer display

3. Trip meter A display

4. Trip meter B display

Odometer

The odometer records the total distance the vehicle has been driven.

Trip meter

The driving distance for a specified interval is indicated. Two types (TRIP A, TRIP B) of interval distance and the average fuel economy for each can be measured.

For instance, trip meter A can record the distance from the point of origin, and trip meter B can record the distance from where the fuel tank is filled.

When trip meter A is selected, TRIP A will be displayed. When trip meter B is selected, TRIP B will be displayed.

The trip meter and average fuel economy can be reset by pressing the TRIP switch for 1.5 seconds or more while in each mode.

 

---

• Only the trip meters record tenths of kilometres (miles).

• The trip record will be erased when:

  • The power supply is interrupted (blown fuse or the battery is disconnected).

  • The vehicle is driven over 9999.9 km (mile).

Close Note

View Note

Displays the engine coolant temperature. The blue range of the gauge indicates that the engine coolant temperature is low, and the red range of the gauge indicates that the engine coolant temperature is high and overheating.

 

---

When the engine coolant temperature gauge needle is in the red range, the engine coolant temperature is extremely high. Drive slowly to reduce engine load. If the engine coolant temperature gauge needle is in the red range, there is the possibility of overheating. Park the vehicle in a safe place immediately and take appropriate measures.

Refer to Overheating (Search).

Close Caution

View Caution

 

---

• If the engine or engine coolant temperature is high or low, the engine output may be restricted to protect the engine.

• During normal driving, the engine coolant temperature stabilizes at 100 °C (210 °F) or less, and the gauge indicates a range lower than 100 °C (210 °F).

Close Note

View Note

The fuel gauge shows approximately how much fuel is remaining in the tank when the ignition is switched ON. We recommend keeping the tank over 1/4 full.

1. Full

2. 1/4 Full

3. Empty

If the low fuel warning light illuminates or the fuel level is very low, refuel as soon as possible.

If inconsistency in engine performance or stalling occurs due to low fuel level conditions, refuel the vehicle as soon as possible and add at least 10 L (2.7 US gal, 2.2 Imp gal) of fuel.

Refer to Low Fuel Warning Indication/Warning Light (Search).

 

---

• After refuelling, it may require some time for the indicator to stabilize. In addition, the indicator may deviate while driving on a slope or curve since the fuel moves in the tank.

• The direction of the arrow () indicates that the fuel-filler flap is on the left side of the vehicle.

Close Note

View Note

(Without auto-light control)

When the lights are turned on with the ignition switched ON, the brightness of the instrument panel illumination is dimmed.

(With auto-light control)

When the lights are turned on with the ignition switched ON, the brightness of the instrument panel illumination is dimmed. However, when the light sensor detects that the surrounding area is bright such as when the lights are turned on in the daytime, the instrument panel illumination does not dim.

 

---

• (With auto-light control)

  When the ignition is switched ON in the early evening or at dusk, the instrument panel illumination is dimmed for several seconds until the light sensor detects the brightness of the surrounding area, however, the dimming may cancel after the brightness is detected.

• When the lights are turned on, the lights-on indicator light in the instrument cluster turns on.

  Refer to Headlights (Search).

Close Note

View Note

The brightness of the instrument panel and instrument panel illuminations can be adjusted by pressing the instrument panel illumination switch while the instrument panel illumination is dimmed.

• The brightness increases by pressing the + switch.

• The brightness decreases by pressing the - switch. If you press the - switch while the instrument cluster is at maximum dimness, a sound is activated to notify you that the current dimmer setting is at maximum dimness.

1. Bright

2. Dim

Function for cancelling illumination dimmer

The illumination dimmer can be cancelled by pressing the + switch while the instrument cluster is at maximum dimness and while the ignition is switched ON. If you press the + switch again while the illumination dimmer is cancelled, a sound is activated to notify you that it is cancelled. If the instrument cluster's visibility is reduced due to glare from surrounding brightness, cancel the illumination dimmer.

 

---

• When the illumination dimmer is cancelled, the instrument cluster cannot be dimmed even if the lights are turned on.

• When the illumination dimmer is cancelled, the screen in the centre display switches to constant display of the daytime screen.

Close Note

View Note

This displays the approximate distance you can travel on the remaining fuel based on the fuel economy.

The distance-to-empty will be calculated and displayed every second.

 

---

• Even though the distance-to-empty display may indicate a sufficient amount of remaining driving distance before refuelling is required, refuel as soon as possible if the fuel level is very low or the low fuel warning light illuminates.

• The display will not change unless you add more than approximately 9 L (2.3 US gal, 1.9 Imp gal) of fuel.

• The distance-to-empty is the approximate remaining distance the vehicle can be driven until all the graduation marks in the fuel gauge indicating the remaining fuel supply disappear.

• If there is no past fuel economy information such as after first purchasing your vehicle or the information is deleted when the battery leads are disconnected, the actual distance-to empty/range may differ from the amount indicated.

Close Note

View Note

The average fuel economy is calculated every minute from the total travelled distance on the trip meter and the total fuel consumption, and the average fuel economy for either drive information display is displayed.

The average fuel economy is also displayed by a red arrow in the instantaneous fuel economy display.

The average fuel economy and trip meters can be reset by pressing the INFO switch for 1.5 seconds or more while in each mode. After the data is cleared, the fuel consumption is recalculated and the - - - L/100 km (- - - mpg) for the 1 minute prior to it being displayed is indicated.

This displays the current fuel economy by calculating the amount of fuel consumption and the distance travelled.

M Hybrid

Except M Hybrid

 

---

• Indicates the 0 position when the vehicle speed is about 5 km/h (3 mph) or slower.

• The red arrow on the scale indicates the average fuel economy.

Close Note

View Note

This displays the status of the charging produced by deceleration regeneration.

Refer to M Hybrid (Search).

In this mode, the current setting for the vehicle speed alarm is displayed. You can change the vehicle speed setting at which the warning is triggered.

 

---

The vehicle speed alarm display is activated at the same time the beep sound is heard.

Close Note

View Note

1. “Speed Alert” message is displayed

The vehicle speed alarm can be set using the centre display.

Refer to the Settings section in the Mazda Connect Owner's Manual.

 

---

Always set the vehicle speed according to the laws and regulations of the country/city in which the vehicle is driven. In addition, always verify the speed of the vehicle using the speedometer.

Close Note

View Note

Displays the system status.

• Refer to Lane Departure Warning System (LDWS) (Search).

• Refer to Blind Spot Monitoring (BSM) (Search).

• Refer to Traffic Sign Recognition System (TSR) (Search).

• Refer to Distance & Speed Alert (DSA) (Search).

• Refer to Driver Attention Alert (DAA) (Search).

• Refer to Driver Monitoring (DM) (Search).

• Refer to Front Cross Traffic Alert (FCTA) (Search).

• Refer to Mazda Radar Cruise Control (MRCC) (Search).

• Refer to Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) (Search).

• Refer to Cruising & Traffic Support (CTS) (Search).

• Refer to Lane-keep Assist System (LAS) (Search).

• Refer to Adjustable Speed Limiter (ASL) (Search).

• Refer to Intelligent Speed Assistance (ISA) (Search).

• Refer to Smart Brake Support (SBS) (Search).

• Refer to Smart Brake Support [Rear] (SBS-R) (Search).

• Refer to Smart Brake Support [Rear Crossing] (SBS-RC) (Search).

• Refer to Cruise Control (Search).

A message such as the system operation status, a malfunction, or an abnormality is indicated.

Warning/indicator light in instrument cluster turns on/flashes or symbol is indicated on display at same time as message

Check the information regarding the warning/indicator light or indicated symbol.

Refer to If a Warning Indication/Warning Lights (Search).

Refer to If a Indication/Indicator Lights (Search).

Message only is indicated on display

Follow the instructions indicated on the display. For the display content, refer to the next page.

Refer to If a Message Indicated on Multi-information Display (Search).

Instrument Cluster varies depending on model and specifications.

1. Instrument Cluster

2. Front Centre of Headliner

Warning lights will appear in any of the highlighted areas

These lights turn on or flash to notify the user of the system operation status or a system malfunction.

Signal	Warning	Refer to
(Red)	Brake System Warning Indication/Warning Light*1	(Search)
	ABS Warning Indication/Warning Light*1	Electronic Brake Force Distribution System Warning (Search)
		ABS warning (Search)
	Charging System Warning Indication/Warning Light*1	(Search)
	Engine Oil Warning Indication/Warning Light*1	(Search)
	High Engine Coolant Temperature Warning Indication	(Search)
	Power Steering Malfunction Indication/Indicator Light*1	(Search)
	Master Warning Indication	(Search)
(Amber)	Brake Control System Warning Indication/Warning Light*1	(Search)
	Brake Override Warning Indication	(Search)
	Check Engine Indication/Light*1	(Search)
	Petrol Particulate Filter Warning Indication/Warning Light*1(SKYACTIV-X 2.0)	(Search)
	Diesel Particulate Filter Warning Indication/Warning Light*1(SKYACTIV-D 1.8)	(Search)
(Amber)	i-stop Warning Indication/Warning Light*1 (Some Models)	(Search)
	Automatic Transmission Warning Indication/Warning Light*1 (Some Models)	(Search)
	AWD Warning Indication/Warning Light*1 (Some Models)	(Search)
	Air Bag/Seat Belt Pretensioner System Warning Indication/Warning Light*1	(Search)
	Tyre Pressure Monitoring System (TPMS) Warning Indication/Warning Light*1 (Some Models)	Flashing (Search)
		Turns on (Search)
(Red)	KEY Warning Indication/Warning Light*1	(Search)
(Amber)	High Beam Control System (HBC) Warning Indication/Warning Light*1 (Some Models)	(Search)
	Adaptive LED Headlights (ALH) Warning Indication/Warning Light*1 (Some Models)	(Search)
	i-ACTIVSENSE Warning Indication/Warning Light*1	(Search)
	Exterior Light Warning Indication/Warning Light*1	(Search)
	Low Fuel Warning Indication/Warning Light	(Search)
	Engine Oil Level Warning Indication/Warning Light*1	(Search)
	120 km/h Warning Light*1 (Some Models)	(Search)
	Seat Belt Warning Indication/Warning Light (Front seat)	(Search)
(Red)	Seat Belt Warning Light (Rear seat)	(Search)
	Low Washer Fluid Level Warning Indication/Warning Light (Some Models)	(Search)
	Door-Ajar Warning Indication	(Search)
	Liftgate-Ajar Warning Indication	(Search)
	Door-Ajar Warning Light	(Search)

1. The light turns on when the ignition is switched on for an operation check, and turns off a few seconds later or when the engine is started. If the light does not turn on or remains turned on, have the vehicle inspected at an expert repairer (we recommend an Authorised Mazda Repairer).

These lights turn on or flash to notify the user of the system operation status or a system malfunction.

Signal	Indicator	Refer to
(Green)	Seat Belt Indicator Light (Rear seat)	(Search)
	Front Passenger Air Bag Deactivation Indicator Light (Some Models)	(Search)
	Security Indicator Light	Immobilizer System (Search)
		Theft-Deterrent System (Search)
		Malfunction (Search)
(Green)	KEY Indicator Light	(Search)
(Green)	i-stop Indicator Light (Some Models)	(Search)
	Wrench Indication/Indicator Light*1	(Search)
	Glow Indicator Light (SKYACTIV-D 1.8)	(Search)
	Shift Position Indication (Some Models)	(Search)
	Lights-On Indicator Light	(Search)
	Headlight High-Beam Indicator Light	Headlight High-Low Beam (Search)
		Flashing the Headlights (Search)
	Rear Fog Light Indicator Light (Some Models)	(Search)
	Direction Indicator/Hazard Warning Indicator Lights	Turn and Lane-Change Signals (Search)
		Hazard Warning Flasher (Search)
	Electric Parking Brake (EPB) Indication/Indicator Light*1*2	(Search)
	AUTOHOLD Active Indicator Light*1	(Search)
	Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) indicator Light (Some Models)	(Search)
	Cruising & Traffic Support (CTS) Indicator Light (Some Models)	(Search)
	TCS/DSC Indication/Indicator Light*1	Traction Control System (TCS) (Search)
		Dynamic Stability Control (DSC) (Search)
		Turns on (Search)
	TCS OFF Indicator Light*1 (Some Models)	(Search)
	Off-Road Traction Assist Indicator Light (AWD) *1 (Some Models)	(Search)
	Select Mode Indicator Light (Some Models)	(Search)
(White)	i-ACTIVSENSE Status Symbol (Warning/Risk Avoidance Support System)	(Search)
(Green)
(Amber)
	i-ACTIVSENSE OFF Symbol (Warning/Risk Avoidance Support System)	(Search)
(Green)	High Beam Control System (HBC) Indicator Light (Some Models)	(Search)
	Adaptive LED Headlights (ALH) Indicator Light (Some Models)	(Search)
(White)	Mazda Radar Cruise Control (MRCC) Standby Indication (Some Models)	(Search)
	Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) Standby Indication (Some Models)	(Search)
	Cruising & Traffic Support (CTS) Standby Indication (Some Models)	(Search)
(Green)	Mazda Radar Cruise Control (MRCC) Set Indication (Some Models)	(Search)
	Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) Set Indication (Some Models)	(Search)
	Cruising & Traffic Support (CTS) Set Indication (Some Models)	(Search)
	Smart Brake Support (SBS) OFF Indicator Light*1 (Some Models)	Smart Brake Support (SBS) (Search)
		Smart Brake Support [Rear] (SBS-R) (Search)
		Smart Brake Support [Rear Crossing] (SBS-RC) (Search)
(White)	Intelligent Speed Assistance (ISA) Standby Indication (Some Models)	(Search)
	Adjustable Speed Limiter (ASL) Standby Indication (Some Models)	(Search)
(Green)	Intelligent Speed Assistance (ISA) Set Indication (Some Models)	(Search)
	Adjustable Speed Limiter (ASL) Set Indication (Some Models)	(Search)
(White)	Cruise Standby Indication (Some Models)	(Search)
(Green)	Cruise Set Indication (Some Models)	(Search)

1. The light turns on when the ignition is switched on for an operation check, and turns off a few seconds later or when the engine is started. If the light does not turn on or remains turned on, have the vehicle inspected at an expert repairer (we recommend an Authorised Mazda Repairer).

2. The light turns on continuously when the parking brake is applied.

The wrench indication/indicator light is displayed/turns on under the following conditions.

• When the preset maintenance period has arrived.

  Refer to the Information section in the Mazda Connect Owner's Manual.

   

  ---

  • When the maintenance period arrives, have your vehicle inspected by an expert repairer (we recommend an Authorised Mazda Repairer) as soon as possible. If maintenance is neglected, a decrease in vehicle performance may occur which could cause damage. Have your vehicle inspected before the maintenance period arrives.

  • If the vehicle continues to be driven after the engine oil replacement period has passed, it could cause damage to the engine. Replace the engine oil before the maintenance period arrives.

  • (SKYACTIV-D 1.8)

    Depending on the vehicle use conditions, engine oil replacement is required due to engine oil deterioration from fuel penetrating the engine oil. If “Excessive Oil Level. Have the Vehicle Inspected” is displayed on the multi-information display in the instrument cluster, have your vehicle inspected at an expert repairer (we recommend an Authorised Mazda Repairer).

  Close Caution

  View Caution

• (SKYACTIV-D 1.8)

  • When fuel filter (sedimentor) draining is required. Consult an expert repairer (we recommend an Authorised Mazda Repairer).

 

---

• The wrench indication/indicator light may display/turn on earlier than the preset period depending on vehicle usage conditions.

• Whenever the engine oil is replaced, a reset of the vehicle engine control unit is necessary.

  Refer to the Information section in the Mazda Connect Owner's Manual.

Close Note

View Note

When the ignition is switched ON, the glow indicator light turns on. The glow indicator light turns off when preheating is finished.

A problem in the system might be indicated under the following conditions. Have your vehicle inspected by an expert repairer (we recommend an Authorised Mazda Repairer).

• The glow indicator light does not turn on when the ignition is switched ON or it remains on.

• The glow indicator light is flashing.

 

---

If the vehicle is left with the ignition switched ON without starting the engine and a long period of time has elapsed since preheating finished, the preheating may be performed again and the glow indicator light may turn on.

Close Note

View Note