Maintenance and CareOwner MaintenanceLight Bulbs

Light Bulbs

Headlights (Low beam)

Headlights (High beam)

Running lights/Position lights

Fog lights (Some Models)

Front direction indicator lights

Position lights

Side direction indicator lights

Camera lamp (Some Models)

Brake lights/Tail lights

Tail lights

Rear direction indicator lights

Tail lights (Liftgate side)

Reverse lights

High-mount brake light

Number plate lights

Overhead light (Front)/Map lights

Vanity mirror lights (Some Models)

Rear map lights

Luggage compartment light

 

Never touch the glass portion of a halogen bulb with your bare hands and always wear eye protection when handling or working around the bulbs:

When a halogen bulb breaks, it is dangerous. These bulbs contain pressurised gas. If one is broken, it will explode and serious injuries could be caused by the flying glass.

If the glass portion is touched with bare hands, body oil could cause the bulb to overheat and explode when lit.

Always keep halogen bulbs out of the reach of children:

Playing with a halogen bulb is dangerous. Serious injuries could be caused by dropping a halogen bulb or breaking it some other way.

Close Warning

 

When removing the lens or lamp unit using a flathead screwdriver, make sure that the flathead screwdriver does not contact the interior terminal. If the flathead screwdriver contacts the terminal, a short circuit may occur.

Close Caution

 

  • To replace the bulb, contact an expert repairer, we recommend an Authorised Mazda Repairer.

  • If the halogen bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used.

  • Use the protective cover and carton for the replacement bulb to dispose of the old bulb promptly and out of the reach of children.

Close Note
Maintenance and CareOwner MaintenanceLight Bulbs

Replacing Exterior Light Bulbs

Headlights (With LED headlights)

Low-beam bulbs, High-beam bulbs, Running lights/Position lights

The LED bulb cannot be replaced as a single unit because it is an integrated unit.

The LED bulb has to be replaced with the unit. We recommend an Authorised Mazda Repairer when the replacement is necessary.

Headlights (With halogen headlights)

Low-beam bulbs, High-beam bulbs

  1. Make sure the ignition is switched off, and the headlight switch is off.

  2. Lift the bonnet.

  3. (Right side)

    Remove the windscreen washer fluid reservoir from the guide.

  4. Disconnect the connector from the unit by pressing the tab on the connector with your finger and pulling the connector downward.

    Low-beam bulbs

    High-beam bulbs

  5. Turn the socket and bulb assembly to remove it. Carefully remove the bulb from its socket in the reflector by gently pulling it straight backward out of the socket.

    Low-beam bulbs

    High-beam bulbs

  6. Install the new bulb in the reverse order of the removal procedure.

Front direction indicator lights, Position lights

  1. Make sure the ignition is switched off, and the headlight switch is off.

  2. If you are changing the right bulb, start the engine, turn the steering wheel all the way to the right, and turn off engine. If you are changing the left bulb, turn the steering wheel to the left.

  3. Pull the centre of each plastic retainer and remove the retainers.

  4. Turn the screw anticlockwise and remove it, and then partially peel back the mudguard.

  5. Turn the socket and bulb assembly anticlockwise and remove it.

  6. Disconnect the bulb from the socket.

    Front direction indicator lights (With LED headlights)

    Front direction indicator lights (With halogen headlights)

    Position lights

  7. Install the new bulb in the reverse order of the removal procedure.

Fog lights (With LED headlights)

The LED bulb cannot be replaced as a single unit because it is an integrated unit.

The LED bulb has to be replaced with the unit. We recommend an Authorised Mazda Repairer when the replacement is necessary.

Fog lights (With halogen headlights) (Some Models)

  1. Make sure the ignition is switched off, and the headlight switch is off.

  2. If you are changing the right bulb, start the engine, turn the steering wheel all the way to the right, and turn off engine. If you are changing the left bulb, turn the steering wheel to the left.

  3. Pull the centre of each plastic retainer and remove the retainers.

  4. Turn the screw anticlockwise and remove it, and then partially peel back the mudguard.

  5. Disconnect the connector from the unit by pressing the tab on the connector with your finger and pulling the connector downward.

  6. Turn the socket and bulb assembly to remove it. Carefully remove the bulb from its socket in the reflector by gently pulling it straight back out of the socket.

  7. Install the new bulb in the reverse order of the removal procedure.

Side-direction indicator lights, Camera lamp (Some Models)

The LED bulb cannot be replaced as a single unit because it is an integrated unit.

The LED bulb has to be replaced with the unit. We recommend an Authorised Mazda Repairer when the replacement is necessary.

Brake lights/Tail lights, Tail lights, Rear direction indicator lights, Reverse lights (With LED headlights)

Brake lights/Tail lights, Tail lights

The LED bulb cannot be replaced as a single unit because it is an integrated unit.

The LED bulb has to be replaced with the unit. We recommend an Authorised Mazda Repairer when the replacement is necessary.

Rear direction indicator lights, Reverse lights

  1. Make sure the ignition is switched off, and the headlight switch is off.

  2. Remove the cover with a cloth-wrapped flathead screwdriver to the cover.

    Rear direction indicator lights

    Reverse lights

  3. Turn the socket and bulb assembly anticlockwise and remove it.

  4. Disconnect the bulb from the socket.

    Rear direction indicator lights

    Reverse lights

  5. Install the new bulb in the reverse order of the removal procedure.

Brake lights/Tail lights, Rear direction indicator lights, Tail lights (Liftgate side), Reverse lights (With halogen headlights)

  1. Make sure the ignition is switched off, and the headlight switch is off.

  2. Remove the cover with a cloth-wrapped flathead screwdriver to the cover.

    Brake lights/Tail lights, Rear direction indicator lights

    Tail lights (Liftgate side), Reverse lights

  3. Turn the socket and bulb assembly anticlockwise and remove it.

  4. Disconnect the bulb from the socket.

    Brake lights/Tail lights

    Rear direction indicator lights

    Tail lights (Liftgate side)

    Reverse lights

  5. Install the new bulb in the reverse order of the removal procedure.

High-mount brake light

The LED bulb cannot be replaced as a single unit because it is an integrated unit.

The LED bulb has to be replaced with the unit. We recommend an Authorised Mazda Repairer when the replacement is necessary.

Number plate lights

  1. Make sure the ignition is switched off, and the headlight switch is off.

  2. Wrap a flathead screwdriver with a soft cloth to prevent damage to the lens, and then remove the lens by carefully prying on the edge of the lens with a flathead screwdriver.

  3. Disconnect the bulb by pulling it out.

  4. Install the new bulb in the reverse order of the removal procedure.

Maintenance and CareOwner MaintenanceLight Bulbs

Replacing Interior Light Bulbs

Overhead light (Front)/Map lights, Rear map lights, Vanity mirror lights (Some Models)

  1. Wrap a small flathead screwdriver with a soft cloth to prevent damage to the lens, and then remove the lens by carefully prying on the edge of the lens with the flathead screwdriver.

  2. Disconnect the bulb by pulling it out.

    Overhead light (Front)/Map lights

    Rear map lights

    Vanity mirror lights

  3. Install the new bulb in the reverse order of the removal procedure.

Luggage compartment light

  1. Wrap a small flathead screwdriver with a soft cloth to prevent damage to the lens and remove the lens unit by carefully prying on the edge of the lens unit with the flathead screwdriver.

  2. Disconnect the electrical connector from the bulb by pressing the tab on the connector with your finger and pulling the connector.

     

    When replacing the bulb always disconnect the connector first. Otherwise, electric and electronic devices could be shorted.

    Close Caution

  3. Insert the flathead screwdriver into the gap between the lens and the lens unit, and then slide the screwdriver to detach the lens.

  4. Disconnect the bulb by pulling it out.

  5. Install the new bulb in the reverse order of the removal procedure.