Owner Maintenance

1. With the vehicle parked, pull the release handle to unlock the bonnet.

    

   

2. Insert your hand into the bonnet opening, slide the latch lever to the right, and lift up the bonnet.

    

   

3. Grasp the support rod in the padded area and secure it in the support rod hole indicated by the arrow to hold the bonnet open.

    

   

1. Check under the bonnet area to make certain all filler caps are in place and all loose items (e.g. tools, oil containers, etc.) have been removed.

2. Lift the bonnet, grasp the padded area on the support rod, and secure the support rod in the clip. Verify that the support rod is secured in the clip before closing the bonnet.

    

   

3. Lower the bonnet slowly to a height of about 20 cm (7.9 in) above its closed position and then let it drop.

 

---

When closing the bonnet, do not push it excessively such as by applying your weight. Otherwise, the bonnet could be deformed.

Close Caution

View Caution

In order to keep the maintenance interval (Search) and to protect the engine from damage caused by poor lubrication, it is vitally important to make use of engine oil with the correct specification. Do not use oils which do not meet the following specifications or requirements. Use of unsuitable oil may lead to engine damage which is not covered by the Mazda Warranty.

Engine oil viscosity, or thickness, has an effect on fuel economy and cold-weather operation (starting and oil flow).

Low-viscosity engine oils can provide improved fuel economy and cold-weather performance.

When choosing an oil, consider the temperature range your vehicle will operate in before the next oil change.

Then select the recommended viscosity from the chart.

 

---

• Using oils of viscosity besides those recommended for specific temperature ranges could result in engine damage.

• (SKYACTIV-D 2.2)

  SKYACTIV-D 2.2 uses specified oil. Please confirm the specification in owner's manual. If engine oil other than the specified oil is used, the Diesel Particulate Filter effective period of use will be shortened or the Diesel Particulate Filter may be damaged.

Close Caution

View Caution

 

---

(SKYACTIV-G 2.0 and SKYACTIV-G 2.5)

• It is normal for all engines to consume engine oil under normal driving conditions.

  Engine oil consumption may be as high as 0.8 L/1,000 km (1 L/800 miles). This may be as a result of evaporation, internal ventilation or burning of the lubricating oil in the working engine. Oil consumption may be higher when the engine is new due to the running-in process. Oil consumption is also dependant on engine speed and engine load. Under extreme driving conditions, oil consumption may be higher.

(SKYACTIV-D 2.2)

• Whenever the engine oil is replaced, the vehicles engine control unit needs to be reset as soon as possible. Otherwise the wrench indicator light or engine oil warning light may turn on. To reset the engine control unit, consult an expert repairer, we recommend an Authorised Mazda Repairer or refer to the vehicle engine control unit reset procedure (Search).

• Inspect the engine oil level periodically. When inspecting the engine oil, if the engine oil level is exceeds the “X” mark on the dipstick, replace the engine oil. This should be done by an expert repairer, we recommend an Authorised Mazda Repairer. When replacing the engine oil, inspect the oil level using the oil dipstick and refill so that the engine oil level is within the range between MIN and MAX as shown in the figure.

   

  

Close Note

View Note

 

---

This procedure is intended for vehicles with SKYACTIV-D 2.2 and vehicles with SKYACTIV-G 2.0 or SKYACTIV-G 2.5 which the engine oil flexible maintenance setting is selected.

Close Note

View Note

After replacing the engine oil, have a repair shop such as an Authorised Mazda Repairer perform the initialization (engine oil data resetting) of the recorded value. If the value recorded by the computer is not initialized, the wrench indicator light may not turn off or it may turn on earlier than normal.

 

---

The initialization (engine oil data resetting) of the recorded value can be performed using the following procedure:

1. Switch the ignition OFF.

2. Switch the ignition ON with the instrument panel illumination knob pressed, and press and hold the instrument panel illumination knob for about 5 seconds until the master warning light flashes.

    

   

3. After the master warning light flashes for several seconds, the initialization is completed.

Close Note

View Note

1. Be sure the vehicle is on a level surface.

2. Warm up the engine to normal operating temperature.

3. Turn it off and wait at least 5 minutes for the oil to return to the sump.

4. Pull out the dipstick, wipe it clean, and reinsert it fully.

   SKYACTIV-G 2.0 and SKYACTIV-G 2.5

    

   

   SKYACTIV-D 2.2

    

   

    

   ---

   (SKYACTIV-D 2.2)

   When inspecting the engine oil level, pull out the dipstick straight without twisting. In addition, when inserting the dipstick, always insert it without twisting so that the “X” mark faces the front of the vehicle.

   Close Note

   View Note

5. Pull it out again and examine the level.

   The level is normal if it is between the MIN and MAX marks.

   If it is near or below MIN, add enough oil to bring the level to MAX.

    

   ---

   Do not overfill the engine oil. This may cause engine damage.

   Close Caution

   View Caution

6. Make sure the O-ring on the dipstick is positioned properly before reinserting the dipstick.

7. Reinsert the dipstick fully.

 

---

Do not use a match or live flame in the engine compartment. DO NOT ADD COOLANT WHEN THE ENGINE IS HOT:

A hot engine is dangerous. If the engine has been running, parts of the engine compartment can become very hot. You could be burned. Carefully inspect the engine coolant in the coolant reservoir, but do not open it.

Pull over to a safe location, then switch the ignition off and make sure the fan is not running before attempting to work near the cooling fan:

Working near the cooling fan when it is running is dangerous. The fan could continue running indefinitely even if the engine has stopped and the engine compartment temperature is high. You could be hit by the fan and seriously injured.

Do not remove either cooling system cap when the engine and radiator are hot:

When the engine and radiator are hot, scalding coolant and steam may shoot out under pressure and cause serious injury.

Close Warning

View Warning

 

---

Changing the coolant should be done by an expert repairer, we recommend an Authorised Mazda Repairer.

Close Note

View Note

Inspect the antifreeze protection and coolant level in the coolant reservoir at least once a year―at the beginning of the winter season―and before travelling where temperatures may drop below freezing.

Inspect the condition and connections of all cooling system and heater hoses.

Replace any that are swollen or deteriorated.

The coolant should be at full in the radiator and between the F and L marks on the coolant reservoir when the engine is cool.

SKYACTIV-G 2.0 and SKYACTIV-G 2.5

SKYACTIV-D 2.2

If it is at or near L, add enough coolant to the coolant reservoir to provide freezing and corrosion protection and to bring the level to F.

Securely tighten the coolant reservoir tank cap after adding coolant.

 

---

• Radiator coolant will damage paint.

  Rinse it off quickly if spilled.

• If the “FL22” mark is shown on or near the cooling system cap, use of FL-22 is recommended when replacing engine coolant. Using engine coolant other than FL-22 may cause serious damage to the engine and cooling system.

 

Close Caution

View Caution

If the coolant reservoir is empty or new coolant is required frequently, consult an expert repairer, we recommend an Authorised Mazda Repairer.

 

---

If the brake/clutch fluid level is low, have the brakes inspected:

A low brake/clutch fluid level is dangerous.

A low level could indicate brake lining wear or a brake system leak which could cause the brakes to fail and lead to an accident.

Close Warning

View Warning

The brakes and clutch draw fluid from the same reservoir.

Inspect the fluid level in the reservoir regularly. It should be kept between the MAX and MIN lines.

The level normally drops with accumulated distance, a condition associated with wear of brake and clutch linings. If it is excessively low, have the brake/clutch system inspected by an expert repairer, we recommend an Authorised Mazda Repairer.

Left-hand drive model

Right-hand drive model

 

---

Use only windscreen washer fluid or plain water in the reservoir:

Using radiator antifreeze as washer fluid is dangerous. If sprayed on the windscreen, it will dirty the windscreen, affect your visibility, and could result in an accident.

Close Warning

View Warning

Inspect fluid level in the washer fluid reservoir; add fluid if necessary.

The top of the float should be between F and L.

Use plain water if washer fluid is unavailable.

But use only washer fluid in cold weather to prevent it from freezing.

 

---

Front and rear washer fluid is supplied from the same reservoir.

Close Note

View Note

When the wipers no longer clean well, the blades are probably worn or cracked.

Replace them.

 

---

• To prevent damage to the wiper arms and other components, do not try to sweep the wiper arm by hand.

• Do not bend the blade rubber unnecessarily when replacing it. Otherwise, the metal stiffener in the blade may deform and the windscreen wiper operation may be adversely affected.

Close Caution

View Caution

 

---

When raising both windscreen wiper arms, raise the driver's side wiper arm first. When lowering the wiper arms, slowly lower the wiper arm from the passenger's side first while supporting it with your hand. Forcefully lowering the wiper arms could damage the wiper arm and blade, and may scratch or crack the windscreen.

Close Note

View Note

1. Raise the wiper arm.

    

   ---

   To prevent damage to the windscreen let the wiper arm down easily, do not let it slap down on the windscreen.

   Close Caution

   View Caution

2. Slide the blade component in the direction of the arrow while pressing the wiper arm tab to remove the blade component from the wiper arm.

    

   

3. Pull the blade rubber in the direction of the arrow and slide it to a position where the blade holder groove can be checked.

    

   

4. Pull the end of the blade rubber from the blade holder groove in the direction of the arrow and remove the blade rubber from the blade holder.

    

   

5. Insert the end of the new blade rubber into the groove of the blade holder until it contacts the end of the blade holder.

    

   

6. After pulling the blade rubber in the direction of the arrow and sliding the blade rubber to a position to check the blade holder groove, slide the blade rubber end in the opposite direction.

    

   

7. Make sure that the blade rubber is correctly installed to the blade holder.

8. Align the wiper arm tabs with the blade component grooves.

    

   

9. Align the blade component projection with the wiper arm notch.

    

   

10. Slide the blade component and install it to the wiper arm.

     

    

11. Slowly lower the wiper arm onto the windscreen.

When the wiper no longer cleans well, the blade is probably worn or cracked.

Replace it.

 

---

To prevent damage to the wiper arm and other components, do not move the wiper by hand.

Close Caution

View Caution

1. Raise the wiper arm and rotate the wiper blade to the right until it unlocks, then remove the blade.

    

   

    

   ---

   To prevent damage to the rear window, do not let the wiper arm fall on it.

   Close Caution

   View Caution

2. Pull down the blade rubber and slide it out of the blade holder.

    

   

3. Remove the metal stiffeners from the blade rubber and install them in the new blade.

    

   

    

   ---

   Do not bend or discard the stiffeners. You need to use them again.

   Close Caution

   View Caution

4. Carefully insert the new blade rubber.

   Then install the blade assembly in the reverse order of removal.

    

   

 

---

Always inflate the tyres to the correct pressure:

Overinflation or underinflation of tyres is dangerous. Adverse handling or unexpected tyre failure could result in a serious accident.

Refer to Tyres (Search).

Use only a Mazda-genuine tyre valve cap:

Use of a non-genuine part is dangerous as the correct tyre air pressure cannot be maintained if the tyre valve becomes damaged. If the vehicle is driven under this condition, the tyre air pressure will decrease which could result in a serious accident. Do not use any part for the tyre valve cap that is not a Mazda-genuine part.

Close Warning

View Warning

Inspect all tyre pressures monthly (including the spare (Some Models)) when the tyres are cold. Maintain recommended pressures for the best ride, handling, and minimum tyre wear.

Refer to the specification charts (Search).

 

---

• Always check tyre pressure when tyres are cold.

• Warm tyres normally exceed recommended pressures. Do not release air from warm tyres to adjust the pressure.

• Underinflation can cause reduced fuel economy, uneven and accelerated tyre wear, and poor sealing of the tyre bead, which will deform the wheel and cause separation of tyre from rim.

• Overinflation can produce a harsh ride, uneven and accelerated tyre wear, and a greater possibility of damage from road hazards.

  Keep your tyre pressure at the correct levels. If one frequently needs inflating, have it inspected.

Close Note

View Note

 

---

Rotate tyres periodically:

Irregular tyre wear is dangerous. To equalize tread wear for maintaining good performance in handling and braking, rotate the tyres every 10,000 km (6,250 miles), or sooner if irregular wear develops.

Close Warning

View Warning

During rotation, inspect them for correct balance.

 

---

(Without temporary spare tyre)

Because your vehicle is not equipped with a spare tyre, you cannot do a tyre rotation safely with the jack that comes with your vehicle. Have an expert repairer, we recommend an Authorised Mazda Repairer perform tyre rotation.

Close Note

View Note

Also, inspect them for uneven wear and damage. Abnormal wear is usually caused by one or a combination of the following:

• Incorrect tyre pressure

• Improper wheel alignment

• Out-of-balance wheel

• Severe braking

After rotation, inflate all tyre pressures to specification (Search) and inspect the wheel nuts for tightness.

 

---

Rotate unidirectional tyres and radial tyres that have an asymmetrical tread pattern or studs only from front to rear, not from side to side. Tyre performance will be reduced if rotated from side to side.

Close Caution

View Caution

 

---

Always use tyres that are in good condition:

Driving with worn tyres is dangerous. Reduced braking, steering, and traction could result in an accident.

Replace all four tyres at the same time:

Replacing just one tyre is dangerous. It could cause poor handling and poor braking resulting in loss of vehicle control. Mazda strongly recommends that you replace all four tyres at the same time.

Close Warning

View Warning

If a tyre wears evenly, a wear indicator will appear as a solid band across the tread.

Replace the tyre when this happens.

You should replace the tyre before the band crosses the entire tread.

Inspect the temporary spare tyre at least monthly to make sure it is properly inflated and stored.

 

---

The temporary spare tyre condition gradually deteriorates even if it has not been used.

Close Note

View Note

The temporary spare tyre is easier to handle because of its construction which is lighter and smaller than a conventional tyre. This tyre should be used only for an emergency and only for a short distance.

Use the temporary spare tyre only until the conventional tyre is repaired, which should be as soon as possible.

Refer to Tyre (Search).

 

---

• Do not use your temporary spare tyre rim with a snow tyre or a conventional tyre. Neither will properly fit and could damage both tyre and rim.

• The temporary spare tyre has a tread life of less than 5,000 km (3,000 miles). The tread life may be shorter depending on driving conditions.

• The temporary spare tyre is for limited use, however, if the tread wear solid-band indicator appears, replace the tyre with the same type of temporary spare (Search).

Close Caution

View Caution

 

---

Always use wheels of the correct size on your vehicle:

Using a wrong-sized wheel is dangerous. Braking and handling could be affected, leading to loss of control and an accident.

Close Warning

View Warning

 

---

A wrong-sized wheel may adversely affect:

• Tyre fit

• Wheel and bearing life

• Ground clearance

• Snow-chain clearance

• Speedometer calibration

• Headlight aim

• Bumper height

• Tyre Pressure Monitoring System (Some Models)

Close Caution

View Caution

 

---

• When replacing a wheel, make sure the new one is the same as the original factory wheel in diameter, rim width, and offset (inset/outset).

• For details, contact an expert repairer, we recommend an Authorised Mazda Repairer.

Close Note

View Note

Proper tyre balancing provides the best riding comfort and helps reduce tread wear. Out-of-balance tyres can cause vibration and uneven wear, such as cupping and flat spots.

Headlights, Running lights/Position lights (Type A), Running lights (Type A), Front fog lights (Some Models), Side direction indicator lights, Brake lights (Type A), Brake lights/Tail lights (Type A), Reverse lights, High-mount brake light

The LED bulb cannot be replaced as a single unit because it is an integrated unit.

The LED bulb has to be replaced with the unit. We recommend an Authorised Mazda Repairer when the replacement is necessary.

Front direction indicator lights, Position lights (Type B)

1. Make sure the ignition is switched off, and the headlight switch is off.

2. Lift the bonnet.

   Refer to Bonnet (Search).

3. Turn the socket and bulb assembly anticlockwise and remove it.

4. Disconnect the bulb from the socket.

   Front direction indicator lights

   

   Position lights

   

5. Install the new bulb in the reverse order of the removal procedure.

Running lights (Type B) (Some Models)

1. Make sure the ignition is switched off, and the headlight switch is off.

2. If you are changing the right bulb, start the engine, turn the steering wheel all the way to the left, and turn off engine. If you are changing the left bulb, turn the steering wheel to the right.

3. Pull the centre of each plastic retainer using a flathead screwdriver and remove the retainers, and then partially peel back the over fender.

   

4. Pull the centre of each plastic retainer using a flathead screwdriver and remove the retainers, and then partially peel back the mudguard.

   

5. Turn the socket and bulb assembly anticlockwise and remove it.

6. Disconnect the bulb from the socket.

   

7. Install the new bulb in the reverse order of the removal procedure.

Rear direction indicator lights, Brake lights/Tail lights (Type B)

1. Make sure the ignition is switched off, and the headlight switch is off.

2. Wrap a small flathead screwdriver with a soft cloth to prevent damage to the cover, and then remove the cover with the flathead screwdriver.

   

3. Turn the screws anticlockwise and remove them.

   

4. Pull the unit rearward to remove it.

   

5. Turn the socket and bulb assembly anticlockwise and remove it.

6. Disconnect the bulb from the socket.

   Rear direction indicator lights

   

   Brake lights/Tail lights

   

7. Install the new bulb in the reverse order of the removal procedure.

Rear fog light (Some Models)

1. Make sure the ignition is switched off and the headlight switch is off.

2. Pull the centre of each plastic retainer and remove the retainers.

3. Remove the cover.

   

4. Turn the socket and bulb assembly anticlockwise and remove it.

5. Disconnect the bulb from the socket.

   

6. Install the new bulb in the reverse order of the removal procedure.

Number plate lights

1. Make sure the ignition is switched off, and the headlight switch is off.

2. Wrap a flathead screwdriver with a soft cloth to prevent damage to the lens, and then remove the lens by carefully prying on the edge of the lens with a flathead screwdriver.

3. Disconnect the bulb by pulling it out.

   

4. Install the new bulb in the reverse order of the removal procedure.

Overhead light/Front map lights, Rear map lights, Vanity mirror lights (Some Models)

1. Wrap a flathead screwdriver with a soft cloth to prevent damage to the lens, and then remove the lens by carefully prying on the edge of the lens with a flathead screwdriver.

2. Disconnect the bulb by pulling it out.

   Overhead light/Front map lights

   

   Rear map lights

   

   Vanity mirror lights (Some Models)

   

3. Install the new bulb in the reverse order of the removal procedure.

Luggage compartment light

1. Wrap a small flathead screwdriver with a soft cloth to prevent damage to the lens and remove the lens unit by carefully prying on the edge of the lens unit with the flathead screwdriver.

   

2. Disconnect the electrical connector from the bulb by pressing the tab on the connector with your finger and pulling the connector.

   

    

   ---

   When replacing the bulb always disconnect the connector first. Otherwise, electric and electronic devices could be shorted.

   Close Caution

   View Caution

3. Insert the flathead screwdriver into the gap between the lens and the lens unit, and then slide the screwdriver to detach the lens.

   

4. Disconnect the bulb by pulling it out.

   

5. Install the new bulb in the reverse order of the removal procedure.

Replacing the fuses on the vehicle's left side

If the electrical system does not work, first inspect the fuses on the vehicle's left side.

1. Make sure the ignition is switched off, and other switches are off.

2. Open the fuse panel cover.

   

3. Pull the fuse straight out with the fuse puller provided on the fuse block located in the engine compartment.

   

4. Inspect the fuse and replace it if it is blown.

   

5. Insert a new fuse of the same amperage rating, and make sure it fits tightly. If it does not fit tightly, have an expert install it. We recommend an Authorised Mazda Repairer.

   If you have no spare fuses, borrow one of the same rating from a circuit not essential to vehicle operation, such as the AUDIO or OUTLET circuit.

    

   ---

   Always replace a fuse with a genuine Mazda fuse or equivalent of the same rating. Otherwise you may damage the electric system.

   Close Caution

   View Caution

6. Reinstall the cover and make sure that it is securely installed.

Replacing the fuses under the bonnet

If the headlights or other electrical components do not work and the fuses in the cabin are normal, inspect the fuse block under the bonnet. If a fuse is blown, it must be replaced. Follow these steps:

1. Make sure the ignition is switched off, and other switches are off.

2. Remove the fuse block cover.

   

3. If any fuse but the MAIN fuse is blown, replace it with a new one of the same amperage rating.

   

    

   ---

   Do not replace the main fuse by yourself. Have an Authorised Mazda Repairer perform the replacement:

   Replacing the fuse by yourself is dangerous because the MAIN fuse is a high current fuse. Incorrect replacement could cause an electrical shock or a short circuit resulting in a fire.

   Close Warning

   View Warning

4. Reinstall the cover and make sure that it is securely installed.

Fuse block (Engine compartment)

DESCRIPTION		FUSE RATING	PROTECTED COMPONENT
1		50 A	For protection of various circuits
2	IG2	30 A	For protection of various circuits
3	INJECTOR ENG.SUB	30 A	Engine control system (Some Models)
4	SCR1 EVVT	20 A	Engine control system (Some Models)
5	P.WINDOW1	30 A	Power windows (Some Models)
6	R.HEATER	20 A	―
7	ADD FAN DE	40 A	Cooling fan (Some Models)
8	WIPER.DEI	20 A	Windscreen wiper de-icer (Some Models)
9	DEFOG	40 A	Rear window defogger
10	DCDC DE	40 A	For protection of various circuits (Some Models)
11	EPB R	20 A	Electric parking brake (EPB) (RH)
12	EPB L	20 A	Electric parking brake (EPB) (LH)
13	AUDIO DCDC REG	30 A	Audio system (Some Models)
14	FAN GE	30 A	Cooling fan (Some Models)
15	ENG.MAIN	40 A	Engine control system
16	ABS/DSC M	50 A	ABS, Dynamic stability control system
17	FAN DE	40 A	Cooling fan (Some Models)
18	WIPER	20 A	Front window wiper and washer
19	HEATER	40 A	Air conditioner
20	ADD FAN GE	30 A	Cooling fan (Some Models)
21	ENGINE.IG1	7.5 A	Engine control system
22	C/U IG1	15 A	For protection of various circuits
23	AUDIO2	7.5 A	Audio system
24	METER2	7.5 A	Instrument cluster (Some Models)
25	ENGINE3	15 A	Engine control system
26	ENGINE2	15 A	Engine control system
27	ENGINE1	15 A	Engine control system
28	AT	15 A	Transaxle control system (Some Models), Ignition switch
29	H/CLEAN	20 A	Headlight washer (Some Models)
30	A/C	7.5 A	Air conditioner (Some Models)
31	AT PUMP	15 A	Transaxle control system (Some Models)
32	HORN	15 A	Horn
33	R.WIPER	15 A	Rear window wiper
34	H/L HI	20 A	Headlight high beam
35	ST.HEATER	15 A	Heated steering wheel (Some Models)
36	FOG	15 A	Fog lights (Some Models)
37		7.5 A	Engine control system
38	H/L LOW L	15 A	Headlight low beam (LH)
39	ENGINE4	15 A	―
40	―	―	―
41	METER1	10 A	Instrument cluster
42	SRS1	7.5 A	Air bag
43	BOSE	25 A	Bose® Sound System-equipped model (Some Models)
44	AUDIO1	15 A	Audio system
45	ABS/DSC S	30 A	ABS, Dynamic stability control system
46	FUEL PUMP	15 A	Fuel system (Some Models)
47	FUEL WARM	25 A	Fuel warmer (Some Models)
48	TAIL	15 A	Tail lights, Number plate lights
49	SCR2 FUEL PUMP2	25 A	―
50	HAZARD	25 A	Hazard warning flashers, Direction indicator lights, Tail lights, Position lights
51	H/L LOW R	15 A	Headlight low beam (RH)
52	OUTLET	25 A	Accessory sockets
53	STOP	10 A	Brake lights
54	ROOM	15 A	Overhead light

Fuse block (Left side)