Air-Conditioning System

Operating Tips

  • Operate the air-conditioning system with the engine running.

  • To prevent the battery from being discharged, do not leave the fan control dial/switch on for a long period of time with the ignition switched ON when the engine is not running.

  • The airflow amount may decrease slightly while the i-stop function is operating.

  • Clear all obstructions such as leaves, snow and ice from the bonnet and the air inlet in the cowl grille to improve the system efficiency.

  • Use the air-conditioning system to defog the windows and dehumidify the air.

  • The recirculate mode should be used when driving through tunnels or while in a traffic jam, or when you would like to shut off outside air for quick cooling of the interior.

  • Use the outside air position for ventilation or windscreen defrosting.

  • If the vehicle has been parked in direct sunlight during hot weather, open the windows to let warm air escape, then run the air-conditioning system.

  • Run the air conditioner about 10 minutes at least once a month to keep internal parts lubricated.

  • Have the air conditioner checked before the weather gets hot. Lack of refrigerant may make the air conditioner less efficient.

    The refrigerant specifications are indicated on a label attached to the inside of the engine compartment. If the wrong type of refrigerant is used, it could result in a serious malfunction of the air conditioner. Consult a professional, government certified repairer for the inspection or repair because a special device is required for the A/C maintenance.

    For details, consult an expert repairer, we recommend an Authorised Mazda Repairer.

Manual Type

Control Switches

Temperature control dial

This dial controls temperature. Turn it clockwise for hot and anticlockwise for cold.

Fan control dial

This dial allows variable fan speeds.

The fan has seven speeds.

Mode selector dial

Turn the mode selector dial to select airflow mode (Search).

 


  • The mode selector dial can be set at the intermediate positions () between each mode. Set the dial to an intermediate position if you want to split the airflow between the two modes.

  • For example, when the mode selector dial is at the position between the and positions, airflow from the floor vent is less than that of the position.

A/C switch

Press the A/C switch to turn the air conditioner on. The indicator light on the switch will illuminate when the fan control dial is in any position except OFF.

 

Press the switch once again to turn the air conditioner off.

 


The air conditioner may not function when the outside temperature approaches 0 °C (32 °F).

Air intake selector

This switch controls the source of air entering the vehicle.

 

Outside or recirculated air positions can be selected. Press the switch to select outside/recirculated air positions.

Recirculated air position (indicator light illuminated)

Outside air is shut off. Use this position when going through tunnels, driving in congested traffic (high engine exhaust areas) or when quick cooling is desired.

Outside air position (indicator light turned off)

Outside air is allowed to enter the cabin. Use this mode for ventilation or windscreen defrosting.

 


Do not use the position in cold or rainy weather:

Using the position in cold or rainy weather is dangerous as it will cause the windows to fog up. Your vision will be hampered, which could lead to a serious accident.

Rear window defogger switch

Press the rear window defogger switch to defrost the rear window.

Refer to Rear Window Defogger (Search).

Cooling

  1. Set the mode selector dial to the position.

  2. Set the temperature control dial to the cold position.

  3. Set the fan control dial to the desired speed.

  4. Turn on the air conditioner by pressing the A/C switch.

  5. After cooling begins, adjust the fan control dial and temperature control dial as needed to maintain maximum comfort.

 


If the air conditioner is used while driving up long hills or in heavy traffic, monitor the high engine coolant temperature warning indication/warning light to see if it is illuminated or flashing (Search).

The air conditioner may cause engine overheating. If the warning light is illuminated or flashing, turn the air-conditioning off (Search).

 


  • When maximum cooling is desired, set the temperature control dial to the extreme cold position and set the air intake selector to the recirculated air position, then turn the fan control dial fully clockwise.

  • If warmer air is desired at floor level, set the mode selector dial at the position and adjust the temperature control dial to maintain maximum comfort.

  • The air to the floor is warmer than air to the face (except when the temperature control dial is set at the extreme hot or cold position).

Ventilation

  1. Set the mode selector dial to the position.

  2. Set the air intake selector to the outside air position (indicator light turns off).

  3. Set the temperature control dial to the desired position.

  4. Set the fan control dial to the desired speed.

Sunlight/Interior temperature sensor

Sunlight sensor

Do not place objects on the sunlight sensor. Otherwise, the interior temperature may not adjust correctly.

Interior temperature sensor

Do not cover the interior temperature sensor. Otherwise, the interior temperature may not adjust correctly.

Page top