i-ACTIVSENSE

• Headlights do not blind drivers approaching in the opposite direction no matter what side of the road you must drive your vehicle (left-hand or right-hand traffic). Therefore, it is not necessary to adjust the optical axis of the headlights when switching temporarily to driving on the opposite side of the road (left-hand or right-hand traffic).

• The Adaptive Front Lighting System (AFS) function can be switched to operable/inoperable using the personalisation function.

  Refer to Personalisation Features (Search).

The timing in which the system switches the headlights changes under the following conditions. If the system does not switch the headlights appropriately, manually switch between high and low beams according to the visibility as well as road and traffic conditions.

• When there are sources of light in the area such as street lamps, illuminated signboards, and traffic signals.

• When there are reflective objects in the surrounding area such as reflective plates and signs.

• When visibility is reduced under rain, snow and foggy conditions.

• When driving on roads with sharp turn or hilly terrain.

• When the headlights/rear lamps of vehicles in front of you or in the opposite lane are dim or not illuminated.

• When there is insufficient darkness such as at dawn or dusk.

• When the luggage compartment is loaded with heavy objects or the rear passenger seats are occupied.

• When visibility is reduced due to a vehicle in front of you spraying water from its tyres onto your windscreen.

• The BSM will operate when all of the following conditions are met:

  • The ignition is switched ON.

  • The BSM OFF indicator light in the instrument cluster is turned off.

  • The vehicle speed is about 30 km/h (19 mph) or faster.

• The BSM will not operate under the following circumstances.

  • The vehicle speed falls below about 25 km/h (15 mph) even though the BSM OFF switch indicator light is turned off.

  • The shift lever (manual transaxle)/selector lever (automatic transaxle) is shifted to reverse (R) and the vehicle is reversing.

  • The turning radius is small (making a sharp turn, turning at intersections).

• In the following cases, the BSM OFF indicator light turns on and operation of the system is stopped. If the BSM OFF indicator light remains illuminated, have the vehicle inspected at an Authorised Mazda Repairer as soon as possible.

  • Some problem with the system including the BSM warning indicator lights is detected.

  • A large deviation in the installation position of a radar sensor (rear) on the vehicle has occurred.

  • There is a large accumulation of snow or ice on the rear bumper near a radar sensor (rear). Remove any snow, ice or mud on the rear bumper.

  • Driving on snow-covered roads for long periods.

  • The temperature near the radar sensors (rear) becomes extremely hot due to driving for long periods on slopes during the summer.

  • The battery voltage has decreased.

• Under the following conditions, the radar sensors (rear) cannot detect target objects or it may be difficult to detect them.

  • A vehicle is in the detection area at the rear in an adjacent driving lane but it does not approach. The BSM determines the condition based on radar detection data.

  • A vehicle is travelling alongside your vehicle at nearly the same speed for an extended period of time.

  • Vehicles approaching in the opposite direction.

  • A vehicle in an adjacent driving lane is attempting to pass your vehicle.

  • A vehicle is in an adjacent lane on a road with extremely wide driving lanes. The detection area of the radar sensors (rear) is set at the road width of expressways.

• In the following case, the flashing of the BSM warning indicator light, and the activation of the warning sound and the warning screen indicator display may not occur or they may be delayed.

  • A vehicle makes a lane change from a driving lane two lanes over to an adjacent lane.

  • Driving on steep slopes.

  • Crossing the summit of a hill or mountain pass.

  • When there is a difference in the height between your driving lane and the adjacent lane.

  • Directly after the BSM system becomes operable by changing the setting.

• If the road width is extremely narrow, vehicles two lanes over may be detected. The detection area of the radar sensors (rear) is set according to the road width of expressways.

• The BSM warning indicator light may turn on and the vehicle detection screen may be displayed in the display in reaction to stationary objects (guardrails, tunnels, sidewalls, and parked vehicles) on the road or the roadside.

  

• A BSM warning indicator light may flash or the warning beep and the warning screen indicator display may be activated several times when making a turn at a city intersection.

• Turn off the BSM while pulling a trailer or while an accessory such as a bicycle carrier is installed to the rear of the vehicle. Otherwise, the radar’s radio waves will be blocked causing the system to not operate normally.

• In the following cases, it may be difficult to view the illumination/flashing of the BSM warning indicator lights equipped on the door mirrors.

  • Snow or ice is adhering to the door mirrors.

  • The front door glass is fogged or covered in snow, frost or dirt.

• The system switches to the Rear Cross Traffic Alert function when the shift lever (manual transaxle) or the selector lever (automatic transaxle) is shifted to the reverse (R) position.

  Refer to Rear Cross Traffic Alert (RCTA) (Search).

• The DAA operates when all of the following conditions are met.

  • The vehicle speed is about 65 to 140 km/h (41 to 86 mph).

  • The system detects white (yellow) lane lines.

  • The system has completed learning of the driver’s driving data.

• The DAA does not operate under the following conditions.

  • The vehicle speed is less than about 65 km/h (41 mph).

  • The vehicle speed exceeds about 140 km/h (86 mph)

  • The vehicle is making a sharp turn.

  • The vehicle is changing lanes.

• The DAA may not operate normally under the following conditions.

  • White (yellow) lane lines are less visible because of dirt or fading/patchiness.

  • The vehicle is jolted or swayed continuously by strong winds or rough roads.

  • The vehicle is driven aggressively.

  • When making frequent lane changes.

• The DAA detects driver fatigue and decreased attentiveness based on the driving data when the vehicle is driven at about 65 to 140 km/h (41 to 86 mph) for about 20 minutes. The driving data will be reset under the following conditions.

  • The vehicle is stopped for 15 minutes or longer.

  • The vehicle is driven at less than about 65 km/h (41 mph) for about 30 minutes.

  • The ignition is switched off.

• After the DAA has displayed the first message encouraging rest, it does not display the next one until 45 minutes have passed.