Flat Tyre

Spare Tyre and Tool Storage

Spare tyre and tools are stored in the locations illustrated in the diagram.

Jack

To remove the jack

Open the luggage board, and lift it.
Remove the jack.

To secure the jack

Perform the removal procedure in reverse.

Maintenance

Always keep the jack clean.
Make sure the moving parts are kept free from dirt or rust.
Make sure the screw thread is adequately lubricated.

Spare Tyre

Your Mazda has a temporary spare tyre.

The temporary spare tyre is lighter and smaller than a conventional tyre, and is designed only for emergency use and should be used only for VERY short periods. Temporary spare tyres should NEVER be used for long drives or extended periods.

Do not install the temporary spare tyre on the front wheels (driving wheels):

Driving with the temporary spare tyre on one of the front driving wheels is dangerous. Handling will be affected. You could lose control of the vehicle, especially on ice or snow bound roads, and have an accident. Move a regular tyre to the front wheel and install the temporary spare tyre to the rear.

Close Warning

View Warning

When using the temporary spare tyre, driving stability may decrease compared to when using only the conventional tyre. Drive carefully.
To avoid damage to the temporary spare tyre or to the vehicle, observe the following precautions:
- Do not exceed 80 km/h (50 mph).
- Avoid driving over obstacles. Also, do not drive through an automatic car wash. This tyre's diameter is smaller than a conventional tyre, so the ground clearance is reduced.
- Do not use a tyre chain on this tyre because it will not fit properly.
- Do not use your temporary spare tyre on any other vehicle, it has been designed only for your Mazda.
- Use only one temporary spare tyre on your vehicle at the same time.

Close Caution

View Caution

To remove the spare tyre

Open the luggage board, and remove it.
For vehicles equipped with a sub-woofer, uncouple the connector.

Extra strength may be required to uncouple the connector. Be sure to squeeze the tab firmly.

Close Note

View Note
For vehicles equipped with a sub-woofer, loosen the hold-down bolt and remove the woofer and spare tyre.
For vehicles not equipped with a sub-woofer, turn the spare tyre hold-down bolt anticlockwise and remove the spare tyre.

To secure the spare tyre

Store the spare tyre in the reverse order of removal. After storing, verify that the spare tyre is stored securely.

Changing a Flat Tyre

If the following occurs while driving, it could indicate a flat tyre.

Steering becomes difficult.
The vehicle begins to vibrate excessively.
The vehicle pulls in one direction.

Close Note

View Note

If you have a flat tyre, drive slowly to a level spot that is well off the road and out of the way of traffic to change the tyre.

Stopping in traffic or on the shoulder of a busy road is dangerous.

Be sure to follow the directions for changing a tyre:

Changing a tyre is dangerous if not done properly. The vehicle can slip off the jack and seriously injure someone.

No person should place any portion of their body under a vehicle that is supported by a jack.

Never allow anyone inside a vehicle supported by a jack:

Allowing someone to remain in a vehicle supported by a jack is dangerous. The occupant could cause the vehicle to fall resulting in serious injury.

Close Warning

View Warning

Make sure the jack is well lubricated before using it.

Close Note

View Note

Park on a hard, level surface off the right-of-way and firmly set the parking brake.
Put a vehicle with an automatic transaxle in Park (P), a manual transaxle in Reverse (R) or 1, and turn off the engine.
Turn on the hazard warning flasher.
Have everyone get out of the vehicle and away from the vehicle and traffic.
Remove the jack, tool, and spare tyre (Search).
Block the wheel diagonally opposite the flat tyre. When blocking a wheel, place a tyre block both in front and behind the tyre.

When blocking a tyre, use rocks or wood blocks of sufficient size if possible to hold the tyre in place.

Close Note

View Note

Removing a Flat Tyre

When jacking-up a vehicle, always shift the shift lever to 1st or R (manual transaxle vehicle) or shift the selector lever to P (automatic transaxle vehicle), apply the parking brake, and place wheel blocks in the position diagonally opposed to the jack:

Changing a flat tyre without using wheel blocks is dangerous because the vehicle may move and fall off the jack even with the shift lever in 1st or R, or the select lever is in P, which could result in an accident.

Close Warning

View Warning

If your vehicle is equipped with steel wheels, pry off the centre cap with the bevelled end of the jack lever.

Use the jack lever when removing the centre cap. Using your hands to remove it may cause an injury. In addition, using a tool other than the jack lever may cause damage to the wheel or the centre cap.

Close Caution

View Caution
Loosen the wheel nuts by turning them anticlockwise one turn each, but do not remove any wheel nuts until the tyre has been raised off the ground.
Place the jack on the ground.
Turn the jack screw in the direction shown in the figure and adjust the jack head so that it is close to the jack-up position.
Place the jack under the jack-up position closest to the tyre being changed with the jack head squarely under the jack-up point.
Continue raising the jack head gradually by rotating the screw with your hand until the jack head is inserted into the jack-up position.

Use only the front and rear jacking positions recommended in this manual:

Attempting to jack the vehicle in positions other than those recommended in this manual is dangerous. The vehicle could slip off the jack and seriously injure or even kill someone. Use only the front and rear jacking positions recommended in this manual.

Do not jack up the vehicle in a position other than the designated jack-up position or place any objects on or under the jack:

Jacking up the vehicle in a position other than the designated jack-up position or placing objects on or under the jack is dangerous as it could deform the vehicle body or the vehicle could fall off the jack resulting in an accident.

Use only the jack provided with your Mazda:

Using a jack that is not designed for your Mazda is dangerous. The vehicle could slip off the jack and seriously injure someone.

Never place objects under the jack:

Jacking the vehicle with an object under the jack is dangerous. The jack could slip and someone could be seriously injured by the jack or the falling vehicle.

Close Warning

View Warning
Insert the jack lever and attach the wheel brace to tyre jack.
Turn the jack handle clockwise and raise the vehicle high enough so that the spare tyre can be installed. Before removing the wheel nuts, make sure your Mazda is firmly in position and that it cannot slip or move.

Do not jack up the vehicle higher than is necessary:

Jacking up the vehicle higher than is necessary is dangerous as it could destabilize the vehicle resulting in an accident.

Do not start the engine or shake the vehicle while it is jacked up:

Starting the engine or shaking the vehicle while it is jacked up is dangerous as it could cause the vehicle to fall off the jack resulting in an accident.

Never go under the vehicle while it is jacked up:

Going under the vehicle while it is jacked up is dangerous as it could result in death or serious injury if the vehicle were to fall off the jack.

Close Warning

View Warning
Remove the wheel nuts by turning them anticlockwise; then remove the wheel and centre cap.

Mounting the Spare Tyre

Remove dirt and grime from the mounting surfaces of the wheel and hub, including the hub bolts, with a cloth.

Make sure the mounting surfaces of the wheel, hub and wheel nuts are clean before changing or replacing tyres:

When changing or replacing a tyre, not removing dirt and grime from the mounting surfaces of the wheel, hub and hub bolts is dangerous. The wheel nuts could loosen while driving and cause the tyre to come off, resulting in an accident.

Close Warning

View Warning
Mount the spare tyre.
Install the wheel nuts with the bevelled edge inward; tighten them by hand.

Do not apply oil or grease to wheel nuts and bolts and do not tighten the wheel nuts beyond the recommended tightening torque:

Applying oil or grease to wheel nuts and bolts is dangerous. The wheel nuts could loosen while driving and cause the tyre to come off, resulting in an accident. In addition, wheel nuts and bolts could be damaged if tightened more than necessary.

Close Warning

View Warning
Turn the wheel brace anticlockwise and lower the vehicle.

Use the wheel brace to tighten the nuts in the order shown.

If you are unsure of how tight the nuts should be, have them inspected at an expert repairer, we recommend an Authorised Mazda Repairer.

Nut tightening torque
N·m (kgf·m, ft·lbf)	108―147 (12―14, 80―108)

Always securely and correctly tighten the wheel nuts:

Improperly or loosely tightened wheel nuts are dangerous. The wheel could wobble or come off. This could result in loss of vehicle control and cause a serious accident.

Be sure to reinstall the same nuts you removed or replace them with metric nuts of the same configuration:

Because the wheel studs and wheel nuts on your Mazda have metric threads, using a non-metric nut is dangerous. On a metric stud, it would not secure the wheel and would damage the stud, which could cause the wheel to slip off and cause an accident.

Close Warning

View Warning

Remove the tyre blocks and store the tools and jack.
Store the damaged tyre in the luggage compartment.
Check the inflation pressure. Refer to Tyres (Search).
Have the flat tyre repaired or replaced as soon as possible.

Do not drive with any tyres that have incorrect air pressure:

Driving on tyres with incorrect air pressure is dangerous. Tyres with incorrect pressure could affect handling and result in an accident. When you check the regular tyres' air pressure, check the spare tyre, too.

Close Warning

View Warning

To prevent the jack and tool from rattling, store them properly.

Close Note

View Note