Seat Belt Systems
Seat Belt Warning Systems
Seat Belt Pretensioner and Load Limiting Systems
SRS Air Bags
Advanced Keyless Entry System
Doors and Locks
Fuel and Emission
Steering Wheel
Mirrors
Windows
Security System
Driving Tips
Saving Fuel and Protection of the Environment
Hazardous Driving
Floor Mat
Rocking the Vehicle
Winter Driving
Driving In Flooded Area
Turbocharger Information
Instrument Cluster and Display
Warning/Indicator Lights
Switches and Controls
Turn and Lane-Change Signals
Windscreen Wipers and Washer
Rear Window Wiper and Washer
Rear Window Defogger
Horn
Hazard Warning Flasher
ABS/TCS/DSC/Trailer Stability Assist (TSA)
Traction Control System (TCS)
Dynamic Stability Control (DSC)
Trailer Stability Assist (TSA)
Fuel Economy Monitor
Drive Selection
i-ACTIV AWD
Power Steering
i-ACTIVSENSE
Adaptive LED Headlights (ALH) (Some Models)
Blind Spot Monitoring (BSM) (Some Models)
Driver Attention Alert (DAA) (Some Models)
Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) (Some Models)
Radar Sensor (Front) (Some Models)
Radar Sensors (Rear) (Some Models)
Ultrasonic Sensor (Rear) (Some Models)
Rear View Monitor
Parking Sensor System
Vent Operation (Front)
Front Air Conditioner
Rear Air Conditioner
Audio Set
Home screen
Volume/Display/Sound Controls
Operating the Radio
Operating the Digital Audio Broadcasting (DAB) Radio (Some Models)
How to use USB mode
Bluetooth®
Bluetooth® Preparation
Available Language
Bluetooth® Audio
How to Use Aha™
How to Use Stitcher™ Radio
Bluetooth® Hands-Free
Settings
Applications
Troubleshooting
Interior Equipment
Scheduled Maintenance
Owner Maintenance
Bonnet
Engine Compartment Overview
Engine Oil
Engine Coolant
Brake Fluid
Washer Fluid
Body Lubrication
Wiper Blades
Battery
Key Battery Replacement
Tyres
Light Bulbs
Fuses
Emission Control Maintenance (Australia)
Flat Tyre
Battery Runs Out
Emergency Starting
Overheating
Emergency Towing
Warning/Indicator Lights and Warning Sounds
Message Indicated in Multi-information Display (Some Models)
Warning Sound is Activated
Active Driving Display Does Not Operate
Cell Phones
Recording of Vehicle Data
Vehicle Telemetry Transfer
Declaration of Conformity
The system operates only when the key is within operational range.
Each time the push button start is pressed, the ignition switches in the order of off, ACC, and ON. Pressing the push button start again from ON switches the ignition off.
The engine starts by pressing the push button start while depressing the brake pedal. To switch the ignition position, press the push button start without depressing the pedal.
Do not leave the ignition switched ON while the engine is not running. Doing so could result in the battery going dead. If the selector lever is in the P position, and the ignition is in ACC, the ignition switches off automatically after about 25 minutes.
Off
The power supply to electrical devices turns off and the push button start indicator light (amber) also turns off.
In this position the steering wheel is locked.
Before leaving the driver's seat, always switch the ignition off, set the parking brake, and make sure the selector lever is in P:
Leaving the driver's seat without switching the ignition off, setting the parking brake, and shifting the selector lever to P is dangerous. Unexpected vehicle movement could occur which could result in an accident.
In addition, if your intention is to leave the vehicle for even a short period, it is important to switch the ignition off, as leaving it in another position will disable some of the vehicle's security systems and run the battery down.
(Locked steering wheel)
If the push button start indicator light (green) is flashing and the beep sound is heard, this indicates that the steering wheel is not unlocked. To unlock the steering wheel, press the push button start while moving the steering wheel left and right.
ACC (Accessory)
Some electrical accessories will operate and the indicator light (amber) illuminates.
In this position the steering wheel is unlocked.
The keyless entry system does not function while the push button start has been pressed to ACC, and the doors will not lock/unlock even if they have been locked manually.
ON
This is the normal running position after the engine is started. The indicator light (amber) turns off. (The indicator light (amber) illuminates when the ignition is switched ON and the engine is not running.)
Some indicator lights/warning lights should be inspected before the engine is started (Search).
When the push button start is pressed to ON, the sound of the fuel pump motor operating near the fuel tank can be heard. This does not indicate an abnormality.
Page top
