Instrument Cluster and Display

Instrument Cluster (Type A)

Speedometer

The speedometer indicates the speed of the vehicle.

Engine Coolant Temperature Gauge

Displays the engine coolant temperature. The blue gauge indicates that the engine coolant temperature is low, and the red gauge indicates that the engine coolant temperature is high and overheating.

 

 

If the engine coolant temperature gauge needle is in the red range, there is the possibility of overheating. Drive slowly to reduce engine load until you can find a safe place to stop the vehicle and wait for the engine to cool down.

Refer to Overheating (Search).

Close Caution
View Caution

 

  • During normal driving, the engine coolant temperature stabilizes at 100 °C (210 °F) or less, and the gauge indicates a range lower than 100 °C (210 °F).

Close Note
View Note

Instrument Panel Illumination

When the lights are turned on with the ignition switched ON, the brightness of the instrument panel illumination is dimmed. However, when the light sensor detects that the surrounding area is bright such as when the lights are turned on in the daytime, the instrument panel illumination does not dim.

 

  • When the ignition is switched ON in the early evening or at dusk, the instrument panel illumination is dimmed for several seconds until the light sensor detects the brightness of the surrounding area, however, the dimming may cancel after the brightness is detected.

  • When the lights are turned on, the lights-on indicator light in the instrument cluster turns on.

    Refer to Headlights (Search).

Close Note
View Note

The brightness of the instrument cluster and instrument panel illuminations can be adjusted by rotating the knob.

  • The brightness decreases by rotating the knob to the left. A beep sound will be heard when the knob has been rotated to the maximum dim position.

  • The brightness increases by rotating the knob to the right.

Function for cancelling illumination dimmer

The illumination dimmer can be cancelled by rotating the instrument panel illumination knob to the right until a beep sound is heard while the instrument cluster is dimmed with the ignition switched ON. If the instrument cluster's visibility is reduced due to glare from surrounding brightness, cancel the illumination dimmer.

 

  • The illumination dimmer can be cancelled by pressing the instrument panel illumination knob. (without speed unit selector)

  • When the illumination dimmer is cancelled, the instrument cluster cannot be dimmed even if the lights are turned on.

  • When the illumination dimmer is cancelled, the screen in the centre display switches to constant display of the daytime screen.

Close Note
View Note

Warning/Indicator Lights

Instrument Cluster varies depending on model and specifications.

Active Driving Display (Some Models)

Active Driving Display (Some Models)

 

Always adjust the display brightness and position with the vehicle stopped:

Adjusting the display brightness and position while driving the vehicle is dangerous as doing so could distract your attention from the road ahead and lead to an accident.

Close Warning
View Warning

 

  • Do not place beverages near the active driving display. If water or other liquids are splashed on the active driving display, it could cause damage.

  • Do not place objects above the active driving display or apply stickers to the dust-proof sheet/optical receiver as they will cause interference.

  • A sensor is integrated to control the display's luminosity. If the optical receiver is covered, the display's luminosity will lower making the display difficult to view.

  • Do not allow intense light to hit the optical receiver. Otherwise, it could cause damage.

Close Caution
View Caution

 

  • Wearing polarized sunglasses will reduce the visibility of the active driving display due to the characteristics of the display.

  • If the battery has been removed and re-installed or the battery voltage is low, the adjusted position may deviate.

  • The display may be difficult to view or temporarily affected by weather conditions such as rain, snow, light, and temperature.

  • If the audio system is removed, the active driving display cannot be operated.

Close Note
View Note

The active driving display indicates the following information:

  • Blind Spot Monitoring (BSM) Operation Conditions and Warnings

    Refer to Blind Spot Monitoring (BSM) (Search).

  • Distance Recognition Support System (DRSS) Warnings

    Refer to Distance Recognition Support System (DRSS) (Search).

  • Traffic Sign Recognition System (TSR) traffic signs and Warnings

    Refer to Traffic Sign Recognition System (TSR) (Search).

  • Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) Operation Conditions and Warnings

    Refer to Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) (Search).

  • Mazda Radar Cruise Control (MRCC) Operation Conditions and Warnings

    Refer to Mazda Radar Cruise Control (MRCC) (Search).

  • Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) Operation Conditions and Warnings

    Refer to Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) (Search).

  • Advanced Smart City Brake Support (Advanced SCBS) Warnings

    Refer to Advanced Smart City Brake Support (Advanced SCBS) (Search).

  • Smart City Brake Support [Forward] (SCBS F) Warnings

    Refer to Smart City Brake Support [Forward] (SCBS F) (Search).

  • Smart City Brake Support [Reverse] (SCBS R) Operation Conditions

    Refer to Smart City Brake Support [Reverse] (SCBS R) (Search).

  • Smart Brake Support (SBS) Warnings

    Refer to Smart Brake Support (SBS) (Search).

  • Driver Attention Alert (DAA) Warnings

    Refer to Driver Attention Alert (DAA) (Search).

  • Cruise Control Operation Conditions

    Refer to Cruise Control (Search).

  • Navigation Guidance (vehicles with navigation system)

  • Speed limit indicator (vehicles with navigation system)

  • Vehicle Speed

Each setting/adjustment for the active driving display can be performed on the centre display.

  1. Select the icon on the home screen and display the Settings screen.

  2. Select the AD-Disp tab.

  3. Select the desired item and perform the setting/adjustment.

    • Method for adjusting screen brightness (automatically/manually)

    • Screen brightness initial settings (automatic adjustment is selected)

    • Screen brightness adjustment (manual adjustment is selected)

    • Display position of active driving display (display height)

    • Active driving display angle adjustment (display angle correction)

    • Active driving display ON/OFF (indication)

    • Navigation guidance ON/OFF

    • Reset settings (reset)

 

  • The desired driving position (display position, brightness level, display information) can be called up after programming the position.

    Refer to Driving Position Memory (Search).

Close Note
View Note

Page top