Instrument Cluster and Display

Multi-information Display (Type A)

The multi-information display indicates the following information.

  • Speedometer

  • Odometer

  • Trip meter

  • Outside temperature

  • Distance-to-empty

  • Average fuel economy

  • Current fuel economy

  • Maintenance Monitor

  • Blind Spot Monitoring (BSM) Display

  • Traffic Sign Recognition System (TSR) Display

  • Distance Recognition Support System (DRSS) Display

  • Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) System Display

  • Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) Display

  • Cruise Control Display

  • Vehicle Speed Alarm

  • Door-Ajar/Liftgate-Ajar Warning Indication

  • Message Display

The screen content changes each time the INFO switch is pressed.

The screen content changes each time the selector knob is pressed and held.

Odometer, Trip Meter and Trip Meter Selector

The odometer is constantly displayed on the screen when the ignition is switched ON, and the TRIP A or TRIP B screen can be displayed by operating the INFO switch.

 

Odometer

The odometer records the total distance the vehicle has been driven.

Trip meter

The driving distance for a specified interval is indicated. Two types (TRIP A, TRIP B) of interval distance and the average fuel economy for each can be measured.

 

For instance, trip meter A can record the distance from the point of origin, and trip meter B can record the distance from where the fuel tank is filled.

 

When trip meter A is selected, TRIP A will be displayed. When trip meter B is selected, TRIP B will be displayed.

 

The trip meter and average fuel economy can be reset by pressing the INFO switch for 1.5 seconds or more while in each mode.

 


  • Only the trip meters record tenths of kilometres (miles).

  • The trip record will be erased when:

    • The power supply is interrupted (blown fuse or the battery is disconnected).

    • The vehicle is driven over 9999.9 km (mile).

Engine Coolant Temperature Gauge

Displays the engine coolant temperature. The blue range of the gauge indicates that the engine coolant temperature is low, and the red range of the gauge indicates that the engine coolant temperature is high and overheating.

 

 


If the engine coolant temperature gauge needle is in the red range, there is the possibility of overheating. Drive slowly to reduce engine load until you can find a safe place to stop the vehicle and wait for the engine to cool down.

Refer to Overheating (Search).

Outside Temperature Display

When the ignition is switched ON, the outside temperature is displayed.

 

 


  • Under the following conditions, the outside temperature display may differ from the actual outside temperature depending on the surroundings and vehicle conditions:

    • Significantly cold or hot temperatures.

    • Sudden changes in outside temperature.

    • The vehicle is parked.

    • The vehicle is driven at low speeds.

Changing the Temperature Unit of the Outside Temperature Display

The outside temperature unit can be switched between Celsius and Fahrenheit.

Settings can be changed by operating the centre display screen.

Refer to Personalisation Features (Search).

 


When the temperature unit indicated in the outside temperature display is changed, the temperature unit indicated in the engine coolant gauge display changes in conjunction with it.

Outside Temperature Warning (Some Models)

When the outside temperature is low, the indication flashes and a beep sound is heard to warn the driver of the possibility of icy roads.

If the outside temperature is lower than about 4 °C (39 °F), the outside temperature display and the mark flashes for about ten seconds and a beep sound is heard once.

 


If the outside temperature is lower than -20 °C (-4 °F), the beep sound does not operate. However, the mark illuminates.

Distance-to-empty

This displays the approximate distance you can travel on the remaining fuel based on the fuel economy.

The distance-to-empty will be calculated and displayed every second.

 

 


  • Even though the distance-to-empty display may indicate a sufficient amount of remaining driving distance before refuelling is required, refuel as soon as possible if the fuel level is very low or the low fuel warning light illuminates.

  • The display will not change unless you add more than approximately 9 L (2.3 US gal, 1.9 Imp gal) of fuel.

  • The distance-to-empty is the approximate remaining distance the vehicle can be driven until all the graduation marks in the fuel gauge indicating the remaining fuel supply disappear.

  • If there is no past fuel economy information such as after first purchasing your vehicle or the information is deleted when the battery leads are disconnected, the actual distance-to empty/range may differ from the amount indicated.

Current Fuel Economy

This displays the current fuel economy by calculating the amount of fuel consumption and the distance travelled.

 

 


  • Indicates the 0 position when the vehicle speed is about 5 km/h (3 mph) or slower.

  • The red arrow on the scale indicates the average fuel economy.

Vehicle Speed Alarm (Some Models)

In this mode, the current setting for the vehicle speed alarm is displayed. You can change the vehicle speed setting at which the warning is triggered.

 


The vehicle speed alarm display is activated at the same time the beep sound is heard.

The vehicle speed alarm can be set using the centre display.

 


Always set the vehicle speed according to the laws and regulations of the country/city in which the vehicle is driven. In addition, always verify the speed of the vehicle using the speedometer.

Blind Spot Monitoring (BSM) Display (Some Models)

Displays the system status.

 

Refer to Blind Spot Monitoring (BSM) (Search).

Warning Indication/Warning Lights

These lights turn on or flash to notify the user of the system operation status or a system malfunction.

Signal

Warning

Page

Brake System Warning Light*1

(Search)

ABS Warning Light*1

Electronic Brake Force Distribution System Warning

(Search)

ABS warning

(Search)

Charging System Warning Indication/Warning Light*1

(Search)

Engine Oil Warning Light*1

(Search)

High Engine Coolant Temperature Warning Indication

(Search)

Power Steering Malfunction Indication

(Search)

Master Warning Indication

(Search)

Electric Parking Brake (EPB) Warning Indication/Warning Light*1

(Search)

Check Engine Light*1 (Some Models)

(Search)

(Amber)

i-stop Warning Light*1 (Some Models)

(Search)

Automatic Transaxle Warning Indication

(Search)

AWD Warning Indication (Some Models)

(Search)

Air Bag/Seat Belt Pretensioner System Warning Light*1

(Search)

Tyre Pressure Monitoring System Warning Light*1 (Some Models)

Flashing

(Search)

Turns on

(Search)

(Amber/White)

KEY Warning Indication

Amber

(Search)

White

(Search)

(Amber)

Adaptive LED Headlights (ALH) Warning Indication/Warning Light*1 (Some Models)

(Search)

Blind Spot Monitoring (BSM) Warning Indication (Some Models)

(Search)

(Amber)

Driver Attention Alert (DAA) Warning Indication (Some Models)

(Search)

(Amber)

Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) Warning Indication (Some Models)

(Search)

Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) Warning Indication (Some Models)

(Search)

LED Headlight Warning Light*1

(Search)

Smart Brake Support/Smart City Brake Support (SBS/SCBS) Warning Indication (Some Models)

(Search)

Low Fuel Warning Indication/Warning Light

(Search)

Check Fuel Cap Warning Indication/Warning Light*1 (Some Models)

(Search)

Engine Oil Level Warning Light*1

(Search)

120 km/h Warning Light*1 (Some Models)

(Search)

Seat Belt Warning Light (Front seat)

(Search)

(Red)

Seat Belt Warning Light (Rear seat)

(Search)

Low Washer Fluid Level Warning Indication (Some Models)

(Search)

Door-Ajar Warning Indication

(Search)

Liftgate-Ajar Warning Indication

(Search)

Door-Ajar Warning Light

(Search)
  1. The light turns on when the ignition is switched on for an operation check, and turns off a few seconds later or when the engine is started. If the light does not turn on or remains turned on, have the vehicle inspected at an expert repairer (we recommend an Authorised Mazda Repairer).

Wrench Indication

The wrench indication is displayed under the following conditions.

  • When the preset maintenance period has arrived.

    Refer to Maintenance Monitor (Search).

  • When the engine oil replacement period has arrived.

 


  • The wrench indication may display earlier than the preset period depending on vehicle usage conditions.

  • Whenever the engine oil is replaced, a reset of the vehicle engine control unit is necessary.

    An expert repairer (we recommend an Authorised Mazda Repairer), will be able to reset the engine control unit or see (Search) for the Vehicle engine control unit reset procedure.

 

Multi-information Display (Type B)

The multi-information display indicates the following information.

  • Odometer

  • Trip meter

  • Engine coolant temperature gauge

  • Fuel gauge

  • Outside temperature

  • Distance-to-empty

  • Average fuel economy

  • Current fuel economy

  • Maintenance Monitor

  • Blind Spot Monitoring (BSM) Display

  • Distance Recognition Support System (DRSS) Display

  • Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) Display

  • Cruise Control Display

  • Vehicle Speed Alarm

  • Message Display

The screen content changes each time the INFO switch is pressed.

Instrument Panel Illumination

When the lights are turned on with the ignition switched ON, the brightness of the instrument panel illumination is dimmed. However, when the light sensor detects that the surrounding area is bright such as when the lights are turned on in the daytime, the instrument panel illumination does not dim.

 


  • When the ignition is switched ON in the early evening or at dusk, the instrument panel illumination is dimmed for several seconds until the light sensor detects the brightness of the surrounding area, however, the dimming may cancel after the brightness is detected.

  • When the lights are turned on, the lights-on indicator light in the instrument cluster turns on.

    Refer to Headlights (Search).

The brightness of the instrument cluster and instrument panel illuminations can be adjusted by rotating the knob.

  • The brightness decreases by rotating the knob to the left. A beep sound will be heard when the knob has been rotated to the maximum dim position.

  • The brightness increases by rotating the knob to the right.

Function for cancelling illumination dimmer

The illumination dimmer can be cancelled by rotating the instrument panel illumination knob to the right until a beep sound is heard while the instrument cluster is dimmed with the ignition switched ON. If the instrument cluster's visibility is reduced due to glare from surrounding brightness, cancel the illumination dimmer.

 


  • The illumination dimmer can be cancelled by pressing the instrument panel illumination knob.

  • When the illumination dimmer is cancelled, the instrument cluster cannot be dimmed even if the lights are turned on.

  • When the illumination dimmer is cancelled, the screen in the centre display switches to constant display of the daytime screen.

Current Fuel Economy

This displays the current fuel economy by calculating the amount of fuel consumption and the distance travelled.

 

 


Indicates the 0 position when the vehicle speed is about 5 km/h (3 mph) or slower.

Maintenance Monitor

The following maintenance period notifications can be displayed by turning the Maintenance Monitor on.

  • Scheduled Maintenance

  • Tyre Rotation

  • Oil Change

When the remaining days to the maintenance period is 15 days or less, or the remaining distance is 1,000 km (600 miles) or shorter, a message is indicated when the ignition is switched ON.

For the setting method and indications for the maintenance monitor, refer to the Maintenance Monitor.

Refer to Maintenance Monitor (Search).

Vehicle Speed Alarm (Some Models)

In this mode, the current setting for the vehicle speed alarm is displayed. You can change the vehicle speed setting at which the warning is triggered.

 


The vehicle speed alarm display is activated at the same time the beep sound is heard.

The vehicle speed alarm can be set using the centre display.

 


Always set the vehicle speed according to the laws and regulations of the country/city in which the vehicle is driven. In addition, always verify the speed of the vehicle using the speedometer.

Vehicle Speed Alarm

In this mode, the current setting for the vehicle speed alarm is displayed. You can change the vehicle speed setting at which the warning is triggered.

 


The vehicle speed alarm display is activated at the same time the beep sound is heard.

The vehicle speed alarm can be set using the centre display.

 


Always set the vehicle speed according to the laws and regulations of the country/city in which the vehicle is driven. In addition, always verify the speed of the vehicle using the speedometer.

Cruise Control Set Vehicle Speed Display

The vehicle speed preset using the cruise control is displayed.

 

Refer to Cruise Control (Search).

Page top