Instrument Cluster and Display

The speedometer indicates the speed of the vehicle.

The tachometer shows engine speed in thousands of revolutions per minute (rpm).

 

---

Do not run the engine with the tachometer needle in the RED ZONE.

This may cause severe engine damage.

 

Close Caution

View Caution

 

---

When the tachometer needle enters the STRIPED ZONE, this indicates to the driver that the gears should be shifted before entering the RED ZONE.

Close Note

View Note

The multi-information display indicates the following information.

• Speedometer

• Odometer

• Trip meter

• Outside temperature

• Distance-to-empty

• Average fuel economy

• Current fuel economy

• Maintenance Monitor

• Blind Spot Monitoring (BSM) Display

• Traffic Sign Recognition System (TSR) Display

• Distance Recognition Support System (DRSS) Display

• Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) System Display

• Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) Display

• Cruise Control Display

• Vehicle Speed Alarm

• Door-Ajar/Liftgate-Ajar Warning Indication

• Message Display

The screen content changes each time the INFO switch is pressed.

The screen content changes each time the selector knob is pressed and held.

The odometer is constantly displayed on the screen when the ignition is switched ON, and the TRIP A or TRIP B screen can be displayed by operating the INFO switch.

Odometer

The odometer records the total distance the vehicle has been driven.

Trip meter

The driving distance for a specified interval is indicated. Two types (TRIP A, TRIP B) of interval distance and the average fuel economy for each can be measured.

For instance, trip meter A can record the distance from the point of origin, and trip meter B can record the distance from where the fuel tank is filled.

When trip meter A is selected, TRIP A will be displayed. When trip meter B is selected, TRIP B will be displayed.

The trip meter and average fuel economy can be reset by pressing the INFO switch for 1.5 seconds or more while in each mode.

 

---

• Only the trip meters record tenths of kilometres (miles).

• The trip record will be erased when:

  • The power supply is interrupted (blown fuse or the battery is disconnected).

  • The vehicle is driven over 9999.9 km (mile).

Close Note

View Note

Displays the engine coolant temperature. The blue range of the gauge indicates that the engine coolant temperature is low, and the red range of the gauge indicates that the engine coolant temperature is high and overheating.

 

---

If the engine coolant temperature gauge needle is in the red range, there is the possibility of overheating. Drive slowly to reduce engine load until you can find a safe place to stop the vehicle and wait for the engine to cool down.

Refer to Overheating (Search).

Close Caution

View Caution

The fuel gauge shows approximately how much fuel is remaining in the tank when the ignition is switched ON. We recommend keeping the tank over 1/4 full.

If the low fuel warning light illuminates or the fuel level is very low, refuel as soon as possible.

If inconsistency in engine performance or stalling occurs due to low fuel level conditions, refuel the vehicle as soon as possible and add at least 10 L (2.7 US gal, 2.2 Imp gal) of fuel.

Refer to Taking Action (Search).

 

---

• After refuelling, it may require some time for the indicator to stabilize. In addition, the indicator may deviate while driving on a slope or curve since the fuel moves in the tank.

• The direction of the arrow () indicates that the fuel-filler flap is on the left side of the vehicle.

Close Note

View Note

When the lights are turned on with the ignition switched ON, the brightness of the instrument panel illumination is dimmed. However, when the light sensor detects that the surrounding area is bright such as when the lights are turned on in the daytime, the instrument panel illumination does not dim.

 

---

• When the ignition is switched ON in the early evening or at dusk, the instrument panel illumination is dimmed for several seconds until the light sensor detects the brightness of the surrounding area, however, the dimming may cancel after the brightness is detected.

• When the lights are turned on, the lights-on indicator light in the instrument cluster turns on.

  Refer to Headlights (Search).

Close Note

View Note

The brightness of the instrument cluster and instrument panel illuminations can be adjusted by rotating the knob.

• The brightness decreases by rotating the knob to the left. A beep sound will be heard when the knob has been rotated to the maximum dim position.

• The brightness increases by rotating the knob to the right.

Function for cancelling illumination dimmer

The illumination dimmer can be cancelled by rotating the instrument panel illumination knob to the right until a beep sound is heard while the instrument cluster is dimmed with the ignition switched ON. If the instrument cluster's visibility is reduced due to glare from surrounding brightness, cancel the illumination dimmer.

 

---

• The illumination dimmer can be cancelled by pressing the instrument panel illumination knob. (without speed unit selector)

• When the illumination dimmer is cancelled, the instrument cluster cannot be dimmed even if the lights are turned on.

• When the illumination dimmer is cancelled, the screen in the centre display switches to constant display of the daytime screen.

Close Note

View Note

When the ignition is switched ON, the outside temperature is displayed.

 

---

• Under the following conditions, the outside temperature display may differ from the actual outside temperature depending on the surroundings and vehicle conditions:

  • Significantly cold or hot temperatures.

  • Sudden changes in outside temperature.

  • The vehicle is parked.

  • The vehicle is driven at low speeds.

Close Note

View Note

Changing the Temperature Unit of the Outside Temperature Display

The outside temperature unit can be switched between Celsius and Fahrenheit.

Settings can be changed by operating the centre display screen.

Refer to Personalisation Features (Search).

 

---

When the temperature unit indicated in the outside temperature display is changed, the temperature unit indicated in the engine coolant gauge display changes in conjunction with it.

Close Note

View Note

Outside Temperature Warning (Some Models)

When the outside temperature is low, the indication flashes and a beep sound is heard to warn the driver of the possibility of icy roads.

If the outside temperature is lower than about 4 °C (39 °F), the outside temperature display and the mark flashes for about ten seconds and a beep sound is heard once.

 

---

If the outside temperature is lower than -20 °C (-4 °F), the beep sound does not operate. However, the mark illuminates.

Close Note

View Note

This displays the approximate distance you can travel on the remaining fuel based on the fuel economy.

The distance-to-empty will be calculated and displayed every second.

 

---

• Even though the distance-to-empty display may indicate a sufficient amount of remaining driving distance before refuelling is required, refuel as soon as possible if the fuel level is very low or the low fuel warning light illuminates.

• The display will not change unless you add more than approximately 9 L (2.3 US gal, 1.9 Imp gal) of fuel.

• The distance-to-empty is the approximate remaining distance the vehicle can be driven until all the graduation marks in the fuel gauge indicating the remaining fuel supply disappear.

• If there is no past fuel economy information such as after first purchasing your vehicle or the information is deleted when the battery leads are disconnected, the actual distance-to empty/range may differ from the amount indicated.

Close Note

View Note

The average fuel economy is calculated every minute from the total travelled distance on the trip meter and the total fuel consumption, and the average fuel economy for either TRIP A or TRIP B is displayed.

The average fuel economy and trip meters can be reset by pressing the INFO switch for 1.5 seconds or more while in each mode. After the data is cleared, the fuel consumption is recalculated and the - - - L/100 km (- - - mpg) for the 1 minute prior to it being displayed is indicated.

This displays the current fuel economy by calculating the amount of fuel consumption and the distance travelled.

 

---

• Indicates the 0 position when the vehicle speed is about 5 km/h (3 mph) or slower.

• The red arrow on the scale indicates the average fuel economy.

Close Note

View Note

The following maintenance period notifications can be displayed by turning the Maintenance Monitor on.

• Scheduled Maintenance

• Tyre Rotation

• Oil Change

When the remaining days to the maintenance period is 15 days or less, or the remaining distance is 1,000 km (600 miles) or shorter, a message is indicated when the ignition is switched ON.

For the setting method and indications for the maintenance monitor, refer to the Maintenance Monitor.

Refer to Maintenance Monitor (Search).

In this mode, the current setting for the vehicle speed alarm is displayed. You can change the vehicle speed setting at which the warning is triggered.

 

---

The vehicle speed alarm display is activated at the same time the beep sound is heard.

Close Note

View Note

The vehicle speed alarm can be set using the centre display.

 

---

Always set the vehicle speed according to the laws and regulations of the country/city in which the vehicle is driven. In addition, always verify the speed of the vehicle using the speedometer.

Close Note

View Note

Displays the system status.

Refer to Blind Spot Monitoring (BSM) (Search).

Displays the system status.

Refer to Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) (Search).

Displays the currently set system status.

Refer to Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) (Search).

Displays the distance between your vehicle and the vehicle ahead.

Refer to Distance Recognition Support System (DRSS) (Search).

The vehicle speed preset using the cruise control is displayed.

Refer to Cruise Control (Search).

A message such as the system operation status, a malfunction, or an abnormality is indicated.

Warning/indicator light in instrument cluster turns on/flashes or symbol is indicated on display at same time as message

Check the information regarding the warning/indicator light or indicated symbol.

Refer to If a Warning Indication/Warning Lights (Search).

Refer to If a Indication/Indicator Lights (Search).

Message only is indicated on display

Follow the instructions indicated on the display. For the display content, refer to the next page.

Refer to If a Message Indicated on Multi-information Display (Search).

Instrument Cluster varies depending on model and specifications.

These lights turn on or flash to notify the user of the system operation status or a system malfunction.

Signal	Warning	Page
	Brake System Warning Light*1	(Search)
	ABS Warning Light*1	Electronic Brake Force Distribution System Warning (Search)
		ABS warning (Search)
	Charging System Warning Indication/Warning Light*1	(Search)
	Engine Oil Warning Light*1	(Search)
	High Engine Coolant Temperature Warning Indication	(Search)
	Power Steering Malfunction Indication	(Search)
	Master Warning Indication	(Search)
	Electric Parking Brake (EPB) Warning Indication/Warning Light*1	(Search)
	Check Engine Light*1 (Some Models)	(Search)
(Amber)	i-stop Warning Light*1 (Some Models)	(Search)
	Automatic Transaxle Warning Indication	(Search)
	AWD Warning Indication (Some Models)	(Search)
	Air Bag/Seat Belt Pretensioner System Warning Light*1	(Search)
	Tyre Pressure Monitoring System Warning Light*1 (Some Models)	Flashing (Search)
		Turns on (Search)
(Amber/White)	KEY Warning Indication	Amber (Search)
		White (Search)
(Amber)	Adaptive LED Headlights (ALH) Warning Indication/Warning Light*1 (Some Models)	(Search)
	Blind Spot Monitoring (BSM) Warning Indication (Some Models)	(Search)
(Amber)	Driver Attention Alert (DAA) Warning Indication (Some Models)	(Search)
(Amber)	Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) Warning Indication (Some Models)	(Search)
	Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) Warning Indication (Some Models)	(Search)
	LED Headlight Warning Light*1	(Search)
	Smart Brake Support/Smart City Brake Support (SBS/SCBS) Warning Indication (Some Models)	(Search)
	Low Fuel Warning Indication/Warning Light	(Search)
	Check Fuel Cap Warning Indication/Warning Light*1 (Some Models)	(Search)
	Engine Oil Level Warning Light*1	(Search)
	120 km/h Warning Light*1 (Some Models)	(Search)
	Seat Belt Warning Light (Front seat)	(Search)
(Red)	Seat Belt Warning Light (Rear seat)	(Search)
	Low Washer Fluid Level Warning Indication (Some Models)	(Search)
	Door-Ajar Warning Indication	(Search)
	Liftgate-Ajar Warning Indication	(Search)
	Door-Ajar Warning Light	(Search)

1. The light turns on when the ignition is switched on for an operation check, and turns off a few seconds later or when the engine is started. If the light does not turn on or remains turned on, have the vehicle inspected at an expert repairer (we recommend an Authorised Mazda Repairer).

These lights turn on or flash to notify the user of the system operation status or a system malfunction.

Signal	Indicator	Page
(Green)	Seat Belt Indicator Light (Rear seat)	(Search)
(Green)	i-stop Warning Light*1 (Some Models)	(Search)
	Security Indicator Light*1	(Search)
	Vehicle Speed Alarm Indication (Some Models)	(Search)
	Wrench Indication	(Search)
	Shift Position Indication	(Search)
	Lights-On Indication/Indicator Light	(Search)
	Headlight High-Beam Indicator Light	Headlight High-Low Beam (Search)
		Flashing the Headlights (Search)
	Front Fog Light Indicator Light (Some Models)	(Search)
	Rear Fog Light Indicator Light (Some Models)	(Search)
	Direction Indicator/Hazard Warning Indicator Lights	Turn and Lane-Change Signals (Search)
		Hazard Warning Flasher (Search)
	Electric Parking Brake (EPB) Indication/Indicator Light*1*2	(Search)
	AUTOHOLD Active Indicator Light*1	(Search)
	Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) indicator Light (Some Models)	(Search)
	TCS/DSC Indicator Light*1	Traction Control System (TCS) (Search)
		Dynamic Stability Control (DSC) (Search)
		Turns on (Search)
	TCS OFF Indicator Light*1 (Some Models)	(Search)
	Off-Road Traction Assist Indicator Light*1 (Some Models)	(Search)
	Select Mode Indication	(Search)
(Green)	Adaptive LED Headlights (ALH) Indicator Light (Some Models)	(Search)
	Blind Spot Monitoring (BSM) OFF Indicator Light*1 (Some Models)	Except malfunction (Search)
		Malfunction (Search)
(White)	Driver Attention Alert (DAA) Indication (Some Models)	(Search)
(White)	Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) Main Indication (Some Models)	(Search)
(Green)	Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) Set Indication (Some Models)	(Search)
	Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) Indication (Some Models)	(Search)
	Smart City Brake Support (SCBS) Indication (Some Models)	Advanced Smart City Brake Support (Advanced SCBS) (Search)
		Smart City Brake Support [Forward] (SCBS F) (Search)
		Smart City Brake Support [Reverse] (SCBS R) (Search)
	Smart Brake Support/Smart City Brake Support (SBS/SCBS) OFF Indicator Light*1 (Some Models)	Advanced Smart City Brake Support (Advanced SCBS) (Search)
		Smart City Brake Support [Forward] (SCBS F) (Search)
		Smart City Brake Support [Reverse] (SCBS R) (Search)
		Smart Brake Support (SBS) System (Search)
(White)	Cruise Main Indication (Some Models)	(Search)
(Green)	Cruise Set Indication (Some Models)	(Search)

1. The light turns on when the ignition is switched on for an operation check, and turns off a few seconds later or when the engine is started. If the light does not turn on or remains turned on, have the vehicle inspected at an expert repairer (we recommend an Authorised Mazda Repairer).

2. The light turns on continuously when the parking brake is applied.

The wrench indication is displayed under the following conditions.

• When the preset maintenance period has arrived.

  Refer to Maintenance Monitor (Search).

• When the engine oil replacement period has arrived.

 

---

• The wrench indication may display earlier than the preset period depending on vehicle usage conditions.

• Whenever the engine oil is replaced, a reset of the vehicle engine control unit is necessary.

  An expert repairer (we recommend an Authorised Mazda Repairer), will be able to reset the engine control unit or see (Search) for the Vehicle engine control unit reset procedure.

Close Note

View Note

The speedometer indicates the speed of the vehicle.

The tachometer shows engine speed in thousands of revolutions per minute (rpm).

 

---

Do not run the engine with the tachometer needle in the RED ZONE.

This may cause severe engine damage.

 

Close Caution

View Caution

 

---

When the tachometer needle enters the STRIPED ZONE, this indicates to the driver that the gears should be shifted before entering the RED ZONE.

Close Note

View Note

The multi-information display indicates the following information.

• Odometer

• Trip meter

• Engine coolant temperature gauge

• Fuel gauge

• Outside temperature

• Trip Computer

• Vehicle Speed Alarm

• Cruise Control Display

The display mode can be changed from odometer to trip meter A to trip meter B and then back to odometer by pressing the selector while one of them is displayed. The selected mode will be displayed.

Odometer

The odometer records the total distance the vehicle has been driven.

Trip meter

The trip meter can record the total distance of two trips. One is recorded in trip meter A, and the other is recorded in trip meter B.

For instance, trip meter A can record the distance from the point of origin, and trip meter B can record the distance from where the fuel tank is filled.

When trip meter A is selected, pressing the selector again within 1 second will change to trip meter B mode.

When trip meter A is selected, TRIP A will be displayed. When trip meter B is selected, TRIP B will be displayed.

The trip meter records the total distance the vehicle is driven until the meter is again reset. Return it to “0.0” by depressing and holding the selector for 1 second or more. Use this meter to measure trip distances and to compute fuel consumption.

 

---

• If TRIP A is reset using the trip meter when the function which synchronizes (resets) the fuel economy monitor and the trip meter (TRIP A) is on, the fuel economy data resets in conjunction with TRIP A.

  Refer to Fuel Economy Monitor (Search).

• Only the trip meters record tenths of kilometres (miles).

• The trip record will be erased when:

  • The power supply is interrupted (blown fuse or the battery is disconnected).

  • The vehicle is driven over 9999.9 km (mile).

Close Note

View Note

Displays the engine coolant temperature. The white range of the gauge indicates that the engine coolant temperature is low, and the red range of the gauge indicates that the engine coolant temperature is high and overheating.

 

---

If the engine coolant temperature gauge needle (white) flashes, there is a possibility of overheating. Drive slowly to reduce engine load until you can find a safe place to stop the vehicle and wait for the engine to cool down.

Refer to Overheating (Search).

Close Caution

View Caution

 

---

• The temperature unit (Centigrade/Fahrenheit) of the engine coolant gauge display changes in conjunction with the temperature unit of the outside temperature display.

  Refer to Personalisation Features (Search).

Close Note

View Note

The fuel gauge shows approximately how much fuel is remaining in the tank when the ignition is switched ON. We recommend keeping the tank over 1/4 full.

If the low fuel warning light illuminates or the fuel level is very low, refuel as soon as possible.

If inconsistency in engine performance or stalling occurs due to low fuel level conditions, refuel the vehicle as soon as possible and add at least 10 L (2.7 US gal, 2.2 Imp gal) of fuel.

Refer to Taking Action (Search).

 

---

• After refuelling, it may require some time for the indicator to stabilize. In addition, the indicator may deviate while driving on a slope or curve since the fuel moves in the tank.

• The display indicating a quarter or less remaining fuel has more segments to show the remaining fuel level in greater detail.

• The direction of the arrow () indicates that the fuel-filler flap is on the left side of the vehicle.

Close Note

View Note

(Without auto-light control)

When the lights are turned on with the ignition switched ON, the brightness of the instrument panel illumination is dimmed.

(With auto-light control)

When the lights are turned on with the ignition switched ON, the brightness of the instrument panel illumination is dimmed. However, when the light sensor detects that the surrounding area is bright such as when the lights are turned on in the daytime, the instrument panel illumination does not dim.

 

---

• (With auto-light control)

  When the ignition is switched ON in the early evening or at dusk, the instrument panel illumination is dimmed for several seconds until the light sensor detects the brightness of the surrounding area, however, the dimming may cancel after the brightness is detected.

• When the lights are turned on, the lights-on indicator light in the instrument cluster turns on.

  Refer to Headlights (Search).

Close Note

View Note

The brightness of the instrument cluster and instrument panel illuminations can be adjusted by rotating the knob.

• The brightness decreases by rotating the knob to the left. A beep sound will be heard when the knob has been rotated to the maximum dim position.

• The brightness increases by rotating the knob to the right.

Function for cancelling illumination dimmer

The illumination dimmer can be cancelled by rotating the instrument panel illumination knob to the right until a beep sound is heard while the instrument cluster is dimmed with the ignition switched ON. If the instrument cluster's visibility is reduced due to glare from surrounding brightness, cancel the illumination dimmer.

 

---

• When the illumination dimmer is cancelled, the instrument cluster cannot be dimmed even if the lights are turned on.

• When the illumination dimmer is cancelled, the screen in the centre display switches to constant display of the daytime screen.

Close Note

View Note

When the ignition is switched ON, the outside temperature is displayed.

 

---

• Under the following conditions, the outside temperature display may differ from the actual outside temperature depending on the surroundings and vehicle conditions:

  • Significantly cold or hot temperatures.

  • Sudden changes in outside temperature.

  • The vehicle is parked.

  • The vehicle is driven at low speeds.

Close Note

View Note

Changing the Temperature Unit of the Outside Temperature Display

The outside temperature unit can be switched between Celsius and Fahrenheit.

Settings can be changed by operating the centre display screen.

Refer to Personalisation Features (Search).

 

---

When the temperature unit indicated in the outside temperature display is changed, the temperature unit indicated in the engine coolant gauge display changes in conjunction with it.

Close Note

View Note

Outside Temperature Warning (Some Models)

When the outside temperature is low, the indication flashes and a beep sound is heard to warn the driver of the possibility of icy roads.

If the outside temperature is lower than about 4 °C (39 °F), the outside temperature display and the mark flashes for about ten seconds and a beep sound is heard once.

 

---

If the outside temperature is lower than -20 °C (-4 °F), the beep sound does not operate. However, the mark illuminates.

Close Note

View Note

The following information can be selected by pressing the INFO switch with the ignition switched ON.

• Distance-to-empty mode

• Average fuel economy mode

• Current fuel economy mode

If you have any problems with your trip computer, consult an expert repairer (we recommend an Authorised Mazda Repairer).

Distance-to-empty mode

This mode displays the approximate distance you can travel on the remaining fuel based on the fuel economy.

The distance-to-empty will be calculated and displayed every second.

(European model)

(Except European model)

 

---

• Even though the distance-to-empty display may indicate a sufficient amount of remaining driving distance before refuelling is required, refuel as soon as possible if the fuel level is very low or the low fuel warning light illuminates.

• The display may not change unless you add more than approximately 9 L (2.3 US gal, 1.9 Imp gal) of fuel.

• The distance-to-empty is the approximate remaining distance the vehicle can be driven until all the graduation marks in the fuel gauge (indicating the remaining fuel supply) disappear.

• If there is no past fuel economy information such as after first purchasing your vehicle or the information is deleted when the battery leads are disconnected, the actual distance-to empty/range may differ from the amount indicated.

Close Note

View Note

Average fuel economy mode

This mode displays the average fuel economy by calculating the total travelled distance and the total fuel consumption since the vehicle was purchased or the past data was reset. The average fuel economy is calculated and displayed every minute.

(European model)

(Except European model)

To reset the displayed past data, press the INFO switch for 1.5 seconds or longer.

 

---

If TRIP A is reset using the trip meter when the function which synchronizes (resets) the fuel economy monitor and the trip meter (TRIP A) is on, the displayed past data is reset.

Close Note

View Note

After resetting the data, - - - L/100 km (- - - mpg) or - - - km/L is displayed for one minute before the fuel economy is recalculated and displayed.

Current fuel economy mode

This mode displays the current fuel economy by calculating the amount of fuel consumption and the distance travelled.

Current fuel economy will be calculated and displayed every 2 seconds.

(European model)

(Except European model)

When you've slowed to about 5 km/h (3 mph), - - - L/100 km (- - - mpg) or - - - km/L will be displayed.

In this mode, the current setting for the vehicle speed alarm is displayed. You can change the vehicle speed setting at which the warning is triggered.

 

---

The vehicle speed alarm display is activated at the same time the beep sound is heard.

Close Note

View Note

The vehicle speed alarm can be set using the centre display.

 

---

Always set the vehicle speed according to the laws and regulations of the country/city in which the vehicle is driven. In addition, always verify the speed of the vehicle using the speedometer.

Close Note

View Note

The vehicle speed preset using the cruise control is displayed.

Refer to Cruise Control (Search).

Instrument Cluster varies depending on model and specifications.

These lights turn on or flash to notify the user of the system operation status or a system malfunction.

Signal	Warning	Page
	Brake System Warning Light*1	(Search)
	ABS Warning Light*1	Electronic Brake Force Distribution System Warning (Search)
		ABS warning (Search)
	Charging System Warning Light*1	(Search)
	Engine Oil Warning Light*1	(Search)
	Power Steering Malfunction Indicator Light*1	(Search)
	Master Warning Light*1	(Search)
	Electric Parking Brake (EPB) Warning Light*1	(Search)
(Red)	Brake Pedal Operation Demand Warning Light*1	Flashing (Search)
		Buzzer & Flashing (Search)
	Check Engine Light*1	(Search)
(Amber)	i-stop Warning Light*1 (Some Models)	(Search)
	Automatic Transaxle Warning Light*1	(Search)
	AWD Warning Light (Some Models)	(Search)
	Air Bag/Seat Belt Pretensioner System Warning Light*1	(Search)
	Tyre Pressure Monitoring System Warning Light*1 (Some Models)	Flashing (Search)
		Turns on (Search)
(Red)	KEY Warning Light*1	Turns on (Search)
		Flashing (Search)
	LED Headlight Warning Light*1	(Search)
	Smart City Brake Support (SCBS) Warning Light (Some Models)	(Search)
	Low Fuel Warning Warning Light	(Search)
	Check Fuel Cap Warning Light*1 (Some Models)	(Search)
	Engine Oil Level Warning Light*1	(Search)
	120 km/h Warning Light*1 (Some Models)	(Search)
	Seat Belt Warning Light (Front seat)	(Search)
	Seat Belt Warning Light (Rear seat)	(Search)
	Low Washer Fluid Level Warning Light (Some Models)	(Search)
	Door-Ajar Warning Light	(Search)

1. The light turns on when the ignition is switched on for an operation check, and turns off a few seconds later or when the engine is started. If the light does not turn on or remains turned on, have the vehicle inspected at an expert repairer (we recommend an Authorised Mazda Repairer).

These lights turn on or flash to notify the user of the system operation status or a system malfunction.

Signal	Indicator	Page
(Green)	Seat Belt Indicator Light (Rear seat)	(Search)
(Green)	i-stop Indicator Light (Some Models)	(Search)
	Security Indicator Light*1	(Search)
	Vehicle Speed Alarm Indication (Some Models)	(Search)
	Wrench Indicator Light*1	(Search)
	Shift Position Indication	(Search)
	Lights-On Indicator Light	(Search)
	Headlight High-Beam Indicator Light	Headlight High-Low Beam (Search)
		Flashing the Headlights (Search)
	Front Fog Light Indicator Light (Some Models)	(Search)
	Rear Fog Light Indicator Light (Some Models)	(Search)
	Direction Indicator/Hazard Warning Indicator Lights	Turn and Lane-Change Signals (Search)
		Hazard Warning Flasher (Search)
	Electric Parking Brake (EPB) Indicator Light*1*2	(Search)
	AUTOHOLD Active Indicator Light*1	(Search)
(Green)	Brake Pedal Operation demand Indicator Light	(Search)
	TCS/DSC Indicator Light*1	Traction Control System (TCS) (Search)
		Dynamic Stability Control (DSC) (Search)
		Turns on (Search)
	TCS OFF Indicator Light*1 (Some Models)	(Search)
	Off-Road Traction Assist Indicator Light*1 (Some Models)	(Search)
	Select Mode Indication	(Search)
	Blind Spot Monitoring (BSM) OFF Indicator Light*1 (Some Models)	Except malfunction (Search)
		Malfunction (Search)
(Red)	Smart City Brake Support (SCBS) Indicator Light (Some Models)	Advanced Smart City Brake Support (Advanced SCBS) (Search)
		Smart City Brake Support [Forward] (SCBS F) (Search)
	Smart City Brake Support (SCBS) OFF Indicator Light*1 (Some Models)	Advanced Smart City Brake Support (Advanced SCBS) (Search)
		Smart City Brake Support [Forward] (SCBS F) (Search)
(White)	Cruise Main Indication	(Search)
(Green)	Cruise Set Indication	(Search)

1. The light turns on when the ignition is switched on for an operation check, and turns off a few seconds later or when the engine is started. If the light does not turn on or remains turned on, have the vehicle inspected at an expert repairer (we recommend an Authorised Mazda Repairer).

2. The light turns on continuously when the parking brake is applied.

When the ignition is switched ON, the wrench indicator light turns on and then turns off after a few seconds.

The wrench indicator light turns on under the following conditions:

• When the preset maintenance period has arrived.

• When it’s time to replace the engine oil.

Refer to Maintenance Monitor (Search).

 

---

• The wrench indicator light turns on earlier than the preset period depending on vehicle usage conditions.

• Whenever the engine oil is replaced, a reset of the vehicle engine control unit is necessary.

  An expert repairer (we recommend an Authorised Mazda Repairer), will be able to reset the engine control unit or see (Search) for the Vehicle engine control unit reset procedure.

Close Note

View Note