Maintenance and CareOwner MaintenanceLight Bulbs

Light Bulbs

Headlights (Low/High beam)

Headlights (Low beam)

Headlights (High beam)

Running lights (Some Models)/Position lights

Front fog lights (Some Models)

Front direction indicator lights

Side direction indicator lights

Brake lights/Tail lights

Rear direction indicator lights

Reverse lights

Rear fog light (Left-hand drive model) (Some Models)

Rear fog light (Right-hand drive model) (Some Models)

Rear fog light (Some Models)

High-mount brake light

Number plate lights

Overhead lights (Front)/Map lights (Some Models)

Overhead lights (Rear) (Some Models)

Boot light (Saloon)

Luggage compartment light (Hatchback)

 

Never touch the glass portion of a halogen bulb with your bare hands and always wear eye protection when handling or working around the bulbs:

When a halogen bulb breaks, it is dangerous. These bulbs contain pressurised gas. If one is broken, it will explode and serious injuries could be caused by the flying glass.

If the glass portion is touched with bare hands, body oil could cause the bulb to overheat and explode when lit.

Always keep halogen bulbs out of the reach of children:

Playing with a halogen bulb is dangerous. Serious injuries could be caused by dropping a halogen bulb or breaking it some other way.

Close Warning

 

When removing the lens or lamp unit using a flathead screwdriver, make sure that the flathead screwdriver does not contact the interior terminal. If the flathead screwdriver contacts the terminal, a short circuit may occur.

Close Caution

 

  • To replace the bulb, contact an expert repairer, we recommend an Authorised Mazda Repairer.

  • If the halogen bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used.

  • Use the protective cover and carton for the replacement bulb to dispose of the old bulb promptly and out of the reach of children.

Close Note
Maintenance and CareOwner MaintenanceLight Bulbs

Replacing Exterior Light Bulbs

Headlights (With LED headlights)

The LED bulb cannot be replaced as a single unit because it is an integrated unit.

The LED bulb has to be replaced with the unit. We recommend an Authorised Mazda Repairer when the replacement is necessary.

Headlights (With halogen headlights)

  1. If you are changing the right bulb, start the engine, turn the steering wheel all the way to the left, and turn off engine. If you are changing the left bulb, turn the steering wheel to the right, and turn off engine.

  2. Make sure the headlight switch is off.

  3. Pull the centre of each plastic retainer and remove the retainers.

     

  4. Turn the screw anticlockwise and remove it, and then partially peel back the mudguard.

     

  5. Disconnect the connector from the bulb.

     

  6. Detach the sealing cover from the bulb.

     

  7. Unhook the bulb retaining spring.

  8. Swing the retaining spring out and away to free the headlight bulb.

  9. Carefully remove the headlight bulb from the socket by pulling it straight back.

  10. Replace the bulb.

  11. Install the new bulb in the reverse order of the removal procedure.

 

  • To replace the bulb, contact an expert repairer, we recommend an Authorised Mazda Repairer.

  • If the halogen bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used.

  • Use the protective cover and carton of the replacement bulb to dispose of the old bulb promptly out of the reach of children.

  • When reinstalling the sealing cover, make sure it is fitted correctly.

Close Note

Running lights/Position lights (With LED headlights)

The LED bulb cannot be replaced as a single unit because it is an integrated unit.

The LED bulb has to be replaced with the unit. We recommend an Authorised Mazda Repairer when the replacement is necessary.

Front direction indicator lights, Running lights (Some Models)/Position lights (With halogen headlights)

  1. If you are changing the right bulb, start the engine, turn the steering wheel all the way to the left, and turn off engine. If you are changing the left bulb, turn the steering wheel to the right, and turn off engine.

  2. Make sure the headlight switch is off.

  3. Pull the centre of each plastic retainer and remove the retainers.

     

  4. Turn the screw anticlockwise and remove it, and then partially peel back the mudguard.

     

  5. Turn the socket and bulb assembly anticlockwise and remove it.

  6. Disconnect the bulb from the socket.

    Front direction indicator lights

     

    Running lights/Position lights (With halogen headlights) (Some Models)

     

    Position lights (With halogen headlights) (Some Models)

     

  7. Install the new bulb in the reverse order of the removal procedure.

Front fog lights (Some Models)

  1. Make sure the ignition is switched off, and the fog light switch is off.

  2. Turn the screw anticlockwise and remove it, and then partially peel back the mudguard.

     

  3. Disconnect the connector from the unit by pressing the tab on the connector with your finger and pulling the connector downward.

     

  4. Turn the socket and bulb assembly to remove it. Carefully remove the bulb from its socket in the reflector by gently pulling it straight backward out of the socket.

     

  5. Install the new bulb in the reverse order of the removal procedure.

Side direction indicator lights, High-mount brake light

The LED bulb cannot be replaced as a single unit because it is an integrated unit.

The LED bulb has to be replaced with the unit. We recommend an Authorised Mazda Repairer when the replacement is necessary.

Rear direction indicator lights, Brake lights/Tail lights

Saloon

  1. Make sure the ignition is switched off, and the headlight switch is off.

  2. Remove the cover.

     

  3. Turn the socket and bulb assembly anticlockwise and remove it.

  4. Disconnect the bulb from the socket.

    Rear direction indicator lights

     

    Brake lights/Tail lights

     

  5. Install the new bulb in the reverse order of the removal procedure.

  6. Insert the cover tabs and install the cover.

 

Verify that the cover is securely installed.

Close Note

Hatchback

  1. Make sure the ignition is switched off, and the headlight switch is off.

  2. Turn the bolts anticlockwise and remove them.

     

  3. Pull the unit rearward to remove it.

     

  4. Turn the socket and bulb assembly anticlockwise and remove it.

  5. Disconnect the bulb from the socket.

    Rear direction indicator lights

     

    Brake lights/Tail lights

    (LED type)

    The LED bulb cannot be replaced as a single unit because it is an integrated unit.

    The LED bulb has to be replaced with the unit. We recommend an Authorised Mazda Repairer when the replacement is necessary.

    (Bulb type)

     

  6. Install the new bulb in the reverse order of the removal procedure.

Reverse lights

Saloon

  1. Make sure the ignition is switched off, and the headlight switch is off.

  2. Pull the centre of each plastic retainer and remove the retainers.

  3. Peel back the boot lid trim.

     

  4. Disconnect the electrical connector from the bulb by pressing the tab on the connector with your finger and pulling the connector.

     

  5. Turn the socket and bulb assembly anticlockwise and remove it.

  6. Disconnect the bulb from the socket.

     

  7. Install the new bulb in the reverse order of the removal procedure.

Hatchback

  1. Make sure the ignition is switched off, and the headlight switch is off.

  2. Pull the centre of each plastic retainer and remove the retainers.

  3. Remove the cover on the interior surface of the liftgate.

     

  4. Disconnect the connector from the socket.

     

  5. Turn the socket and bulb assembly anticlockwise and remove it.

  6. Disconnect the bulb from the socket.

     

  7. Install the new bulb in the reverse order of the removal procedure.

Rear fog light (Some Models)

Saloon

  1. Make sure the ignition is switched off, and the headlight switch is off.

  2. Turn the socket and bulb assembly anticlockwise and remove it.

  3. Disconnect the bulb from the socket.

     

  4. Install the new bulb in the reverse order of the removal procedure.

Hatchback

  1. Make sure the ignition is switched off and the headlight switch is off.

  2. Turn the screw anticlockwise and remove it, and then partially peel back the mudguard.

     

  3. Turn the socket and bulb assembly anticlockwise and remove it.

  4. Disconnect the bulb from the socket.

     

  5. Install the new bulb in the reverse order of the removal procedure.

Number plate lights

Saloon

  1. Make sure the ignition is switched off, and the headlight switch is off.

  2. Pull the centre of each plastic retainer and remove the retainers.

  3. Peel back the boot lid trim.

     

  4. Turn the socket and bulb assembly anticlockwise and remove it.

  5. Disconnect the bulb from the socket.

     

  6. Install the new bulb in the reverse order of the removal procedure.

Hatchback

  1. Make sure the ignition is switched off, and the headlight switch is off.

  2. Wrap a flathead screwdriver with a soft cloth to prevent damage to the light unit.

  3. Insert a flathead screwdriver into the position shown in the figure and pull the light unit outward.

     

  4. Disconnect the electrical connector from the bulb by pressing the tab on the connector with your finger and pulling the connector.

     

  5. Turn the socket and bulb assembly anticlockwise and remove it.

  6. Disconnect the bulb from the socket.

     

  7. Install the new bulb in the reverse order of the removal procedure.

Maintenance and CareOwner MaintenanceLight Bulbs

Replacing Interior Light Bulbs

Overhead lights/Map lights (Some Models), Overhead lights (Front) (Some Models), Overhead lights (Rear) (Some Models)

  1. Wrap a small flathead screwdriver with a soft cloth to prevent damage to the lens, and then remove the lens by carefully prying on the edge of the lens with the flathead screwdriver.

  2. Disconnect the bulb by pulling it out.

    Overhead lights/Map lights (Some Models)

     

     

    Overhead lights (Front) (Some Models)

     

    Overhead lights (Rear) (Some Models)

     

  3. Install the new bulb in the reverse order of the removal procedure.

Boot light (Saloon)

  1. Press both sides of the lens cap to remove it.

  2. Disconnect the bulb by pulling it out.

     

  3. Install the new bulb in the reverse order of the removal procedure.

Luggage compartment light (Hatchback)

  1. Wrap a small flathead screwdriver with a soft cloth to prevent damage to the lens and remove the lens by carefully prying on the edge of the lens with the flathead screwdriver.

  2. Disconnect the bulb by pulling it out.

     

  3. Install the new bulb in the reverse order of the removal procedure.