Air-Conditioning System
Operating Tips
-
Operate the air-conditioning system with the engine running.
-
To prevent the battery from being discharged, do not leave the fan control dial on for a long period of time with the ignition switched ON when the engine is not running.
-
(With i-stop)
The airflow amount may decrease slightly while the i-stop function is operating.
-
Clear all obstructions such as leaves, snow and ice from the bonnet and the air inlet in the cowl grille to improve the system efficiency.
-
Use the air-conditioning system to defog the windows and dehumidify the air.
-
The recirculate mode should be used when driving through tunnels or while in a traffic jam, or when you would like to shut off outside air for quick cooling of the interior.
-
Use the outside air position for ventilation or windscreen defrosting.
-
If the vehicle has been parked in direct sunlight during hot weather, open the windows to let warm air escape, then run the air-conditioning system.
(With A/C switch)
-
Run the air conditioner about 10 minutes at least once a month to keep internal parts lubricated.
-
Have the air conditioner checked before the weather gets hot. Lack of refrigerant may make the air conditioner less efficient.
The refrigerant specifications are indicated on a label attached to the inside of the engine compartment. If the wrong type of refrigerant is used, it could result in a serious malfunction of the air conditioner. Consult a professional, government certified repairer for the inspection or repair because a special device is required for the air conditioner maintenance.
For details, consult an expert repairer, we recommend an Authorised Mazda Repairer.
Vent Operation
Adjusting the Vents
Directing airflow
To adjust the direction of airflow, move the adjustment knob.
-
When using the air conditioner under humid ambient temperature conditions, the system may blow fog from the vents. This is not a sign of trouble but a result of humid air being suddenly cooled.
Centre vents (driver) and Side vents
Air vent open/close
Airflow direction adjustment
Centre vents (front passenger)
Air vent open/close
Airflow direction adjustment
Selecting the Airflow Mode
The location airflow exits the air vents and the airflow amount may change depending on the open or close status of the air vents.
Manual Type
Control Switches
Temperature control dial
(Type A/Type B/Type C)
This dial controls temperature. Turn it clockwise for hot and anticlockwise for cold.
(Type D)
This dial controls the air temperature when using the air conditioner. Turn it clockwise for cold.
Fan control dial
This dial allows variable fan speeds.
(Type A/Type B)
This fan has seven speeds.
(Type C/Type D)
0―Fan off
1―Low speed
2―Medium low speed
3―Medium high speed
4―High speed
Mode selector dial
Turn the mode selector dial to select airflow mode (Search).
-
The mode selector dial can be set at the intermediate positions (
) between each mode. Set the dial to an intermediate position if you want to split the airflow between the two modes. -
For example, when the mode selector dial is at the
position between the 
and 
positions, airflow from the floor vent is less than that of the position.
A/C switch (Type A/Type C/Type D)
(Type A)
Press the A/C switch to turn the air conditioner on. The indicator light on the switch will illuminate when the fan control dial is in any position except OFF.
(Type C/Type D)
Press the A/C switch to turn the air conditioner on. The indicator light on the switch will illuminate when the fan control dial is set at position 1, 2, 3, or 4.
Press the switch once again to turn the air conditioner off.
The air conditioner may not function when the outside temperature approaches 0 °C (32 °F).
Air intake selector (Type A/Type B)
This switch controls the source of air entering the vehicle.
Press the air intake selector switch to alternate between the outside air and recirculated air positions.
Recirculated air position (
)
Outside air is shut off. Air within the vehicle is recirculated.
Outside air position (
)
Outside air is allowed to enter the cabin. Use this mode for ventilation or windscreen defrosting.
Do not use the recirculated air position in cold or rainy weather:
Using the recirculated air position in cold or rainy weather is dangerous as it will cause the windows to fog up. Your vision will be hampered, which could lead to a serious accident.
Air intake selector (Type C/Type D)
This lever controls the source of air entering the vehicle.
It is recommended that under normal conditions the switch be kept in the outside air position.
Recirculated air position ()
Outside air is shut off. Air within the vehicle is recirculated.
Outside air position ()
(Type C)
Outside air is taken into the vehicle. Use this position for normal ventilation and heating.
(Type D)
Outside air is taken into the vehicle. Use this position for normal ventilation.
Do not use the position in cold or rainy weather:
Using the position in cold or rainy weather is dangerous as it will cause the windows to fog up. Your vision will be hampered, which could lead to a serious accident.
Rear window defogger switch
Press the rear window defogger switch to defrost the rear window.
Refer to Rear Window Defogger (Search).
Heating (Some Models)
-
Set the mode selector dial to the
position. -
(Type A/Type B)
Set the air intake selector to the outside air position.
(Type C)
Set the air intake selector to the
position. -
Set the temperature control dial to the hot position.
-
Set the fan control dial to the desired speed.
-
(Type A/Type C)
If dehumidified heating is desired, turn on the air conditioner.
-
If the windscreen fogs up easily, set the mode selector dial to the
position. -
(Type A/Type C)
If cooler air is desired at face level, set the mode selector dial to the
position and adjust the temperature control dial to maintain maximum comfort. -
The air to the floor is warmer than air to the face (except when the temperature control dial is set at the extreme hot or cold position).
Cooling (With air conditioner)
-
Set the mode selector dial to the
position. -
Set the temperature control dial to the cold position.
-
Set the fan control dial to the desired speed.
-
Turn on the air conditioner by pressing the A/C switch.
-
After cooling begins, adjust the fan control dial and temperature control dial as needed to maintain maximum comfort.
If the air conditioner is used while driving up long hills or in heavy traffic, monitor the high engine coolant temperature warning light to see if it is illuminated or flashing (Search).
The air conditioner may cause engine overheating. If the warning light is illuminated or flashing, turn the air conditioner off (Search).
-
(Type A)
When maximum cooling is desired, set the temperature control dial to the extreme cold position and set the air intake selector to the recirculated air position, then turn the fan control dial fully clockwise.
-
(Type C/Type D)
When maximum cooling is desired, set the temperature control dial to the extreme cold position and set the air intake selector to the recirculated air position, then set the fan control dial to position 4.
-
(Type A/Type C)
If warmer air is desired at floor level, set the mode selector dial to the
position and adjust the temperature control dial to maintain maximum comfort. -
The air to the floor is warmer than air to the face (except when the temperature control dial is set at the extreme hot or cold position).
Ventilation
-
Set the mode selector dial to the
position. -
(Type A/Type B)
Set the air intake selector to the outside air position.
(Type C/Type D)
Set the air intake selector to the
position. -
Set the temperature control dial to the desired position.
-
Set the fan control dial to the desired speed.
Windscreen Defrosting and Defogging
-
Set the mode selector dial to the
position. -
(Type C/Type D)
Set the air intake selector to the
position. -
Set the temperature control dial to the desired position.
-
Set the fan control dial to the desired speed.
-
(Type A/Type C)
If dehumidified heating is desired, turn on the air conditioner.
(Type D)
Press the A/C switch to turn on the air conditioner.
Do not defog the windscreen using the position with the temperature control set to the cold position (Type A/Type B/Type C):
Using the position with the temperature control set to the cold position is dangerous as it will cause the outside of the windscreen to fog up. Your vision will be hampered, which could lead to a serious accident. Set the temperature control to the hot or warm position when using the position.
Do not leave the air conditioner in the position with the temperature control set to cold after the windscreen has defogged (Type D):
Leaving the air conditioner in the position with the temperature control set to cold after the windscreen has defogged is dangerous as the outside of the windscreen will fog up. Your vision will be hampered, which could lead to a serious accident.
Set the mode selector dial except the position and turn on the windscreen wipers to clear the window.
-
(Type A)
For maximum defrosting, turn on the air conditioner, set the temperature control dial to the extreme hot position, and turn the fan control dial fully clockwise.
-
(Type C)
For maximum defrosting, turn on the air conditioner, set the temperature control dial to the extreme hot position, and the fan control dial to position 4.
-
(Type A/Type C)
If warm air is desired at the floor, set the mode selector dial to the
position. -
(Type A/Type B)
In the
position, the outside air position is automatically selected. The air intake selector cannot be changed to the recirculated air position.
Dehumidifying (With air conditioner)
Fully Automatic Type
Control Switches
Temperature control dial
This dial controls temperature. Turn it clockwise for hot and anticlockwise for cold.
Fan control dial
The fan has seven speeds.
AUTO position
The amount of airflow will be automatically controlled in accordance with the set temperature.
Except AUTO position
The airflow amount can be adjusted to the desired level by turning the dial.
0 position
To turn off the system, set the dial to 0 position.
Mode selector dial
Turn the mode selector dial to select airflow mode (Search).
AUTO position
The airflow mode automatically adjusts to the selected temperature.
Except AUTO position
The desired airflow position can be selected by turning the dial.
-
With the airflow mode set to the
position and the temperature control dial set at a medium temperature, heated air is directed to the feet and air at a comparably lower temperature will flow through the central, left and right vents. -
When the fan control dial is ON, and the mode selector dial is in the
position, the air conditioner is automatically turned on and the outside air position is automatically selected to defrost the windscreen.
A/C switch
The air conditioner (cooling/dehumidifying functions) can be turned on or off by pressing the switch while the fan control dial is at a position other than 0.
The indicator light turns on while the air conditioner is operating.
The air conditioner may not function when the outside temperature approaches 0 °C (32 °F).
Air intake selector
Outside or recirculated air positions can be selected. Press the switch to select outside/recirculated air positions.
Recirculated air position (indicator light illuminated)
Outside air is shut off. Use this position when going through tunnels, driving in congested traffic (high engine exhaust areas) or when quick cooling is desired.
Outside air position (indicator light turned off)
Outside air is allowed to enter the cabin. Use this mode for ventilation or windscreen defrosting.
Do not use the position in cold or rainy weather:
Using the position in cold or rainy weather is dangerous as it will cause the windows to fog up. Your vision will be hampered, which could lead to a serious accident.
Rear window defogger switch
Press the rear window defogger switch to defrost the rear window.
Refer to Rear Window Defogger (Search).
Operation of Automatic Air Conditioner
-
Set the mode selector dial to the AUTO position.
-
Set the air intake selector to the outside air position (indicator light turned off).
If the recirculated air position is used for long periods in cold weather or high humidity, the windscreen may fog up more easily.
-
Set the fan control dial to the AUTO position.
-
Press the A/C switch to operate the air conditioner (turn indicator light on).
-
Set the temperature control dial to the desired position.
-
To turn off the system, set the fan control dial to the 0 position.
-
Setting the temperature to maximum hot or cold will not provide the desired temperature at a faster rate.
-
When selecting heat, the system will restrict airflow until it has warmed to prevent cold air from blowing out of the vents.
Windscreen Defrosting and Defogging
Set the mode selector dial to the position and turn the fan control dial to the desired speed.
In this position, the outside air position is automatically selected, and when the fan control dial is ON, the air conditioner automatically turns on. The air conditioner will directly dehumidify the air to the front windscreen and side windows (Search). Airflow amount will be increased.
Set the temperature control to the hot or warm position when defogging ( position):
Using the position with the temperature control set to the cold position is dangerous as it will cause the outside of the windscreen to fog up. Your vision will be hampered, which could lead to a serious accident.
Use the temperature control dial to increase the air flow temperature and defog the windscreen more quickly.
Sunlight/Temperature Sensor
Sunlight sensor
Do not place objects on the sunlight sensor. Otherwise, the interior temperature may not adjust correctly.
Interior temperature sensor
Do not cover the interior temperature sensor. Otherwise, the interior temperature may not adjust correctly.
