Maintenance and Care Owner Maintenance Bonnet

Owner Maintenance

Owner Maintenance Precautions

Maintenance and Care Owner Maintenance Owner Maintenance Precautions

Owner Maintenance Precautions

Routine Service

We highly recommend that these items be inspected daily, or at least every week.

Engine Oil Level (Search)
Engine Coolant Level (Search)
Brake and clutch Fluid Level (Search)
Washer Fluid Level (Search)
Battery Maintenance (Search)
Tyre Inflation Pressure (Search)

Improper or incomplete service may result in problems. This section gives instructions only for items that are easy to perform.

As explained in the Introduction (Search), several procedures can be done only by a qualified service technician with special tools.

Improper do-it yourself maintenance during the warranty period may affect warranty coverage. For details, read the separate Mazda Warranty statement provided with the vehicle. If you are unsure about any servicing or maintenance procedure, have it done by an expert repairer, we recommend an Authorised Mazda Repairer.

There are strict environmental laws regarding the disposal of waste oil and fluids. Please dispose of your waste properly and with due regard to the environment.

We recommend that you entrust the oil and fluid changes of your vehicle to an Authorised Mazda Repairer.

Do not perform maintenance work if you lack sufficient knowledge and experience or the proper tools and equipment to do the work. Have maintenance work done by a qualified technician:

Performing maintenance work on a vehicle is dangerous if not done properly. You can be seriously injured while performing some maintenance procedures.

If you must run the engine while working under the bonnet, make certain that you remove all jewellery (especially rings, bracelets, watches, and necklaces) and all neckties, scarves, and similar loose clothing before getting near the engine or cooling fan which may turn on unexpectedly:

Working under the bonnet with the engine running is dangerous. It becomes even more dangerous when you wear jewellery or loose clothing.

Either can become entangled in moving parts and result in injury.

Pull over to a safe location, then switch the ignition off and make sure the fan is not running before attempting to work near the cooling fan:

Working near the cooling fan when it is running is dangerous. The fan could continue running indefinitely even if the engine has stopped and the engine compartment temperature is high. You could be hit by the fan and seriously injured.

Do not leave items in the engine compartment:

After you have finished checking or doing servicing in the engine compartment, do not forget and leave items such as tools or rags in the engine compartment.

Tools or other items left in the engine compartment could cause engine damage or a fire leading to an unexpected accident.

Close Warning

View Warning

Bonnet

Maintenance and Care Owner Maintenance Bonnet

Bonnet

Always check that the bonnet is closed and securely locked:

A bonnet that is not closed and securely locked is dangerous as it could fly open while the vehicle is moving and block the driver's vision which could result in a serious accident.

Close Warning

View Warning

Maintenance and Care Owner Maintenance Bonnet

Opening the Bonnet

With the vehicle parked, pull the release handle to unlock the bonnet.
Insert your hand into the bonnet opening, slide the latch lever to the right, and lift up the bonnet.

The lever is located a little to the left of centre when facing the vehicle.

Close Note

View Note
Grasp the support rod in the padded area and secure it in the support rod hole indicated by the arrow to hold the bonnet open.

Maintenance and Care Owner Maintenance Bonnet

Closing the Bonnet

Check under the bonnet area to make certain all filler caps are in place and all loose items (e.g. tools, oil containers, etc.) have been removed.
Lift the bonnet, grasp the padded area on the support rod, and secure the support rod in the clip. Verify that the support rod is secured in the clip before closing the bonnet.
Lower the bonnet slowly to a height of about 20 cm (7.9 in) above its closed position and then let it drop.

When closing the bonnet, do not push it excessively such as by applying your weight. Otherwise, the bonnet could be deformed.

Close Caution

View Caution

Engine Compartment Overview

Maintenance and Care Owner Maintenance Engine Compartment Overview

Engine Compartment Overview

Engine Oil

Maintenance and Care Owner Maintenance Engine Oil

Engine Oil

Changing the engine oil should be done by an expert repairer, we recommend an Authorised Mazda Repairer.

Close Note

View Note

Maintenance and Care Owner Maintenance Engine Oil

Recommended Oil

In order to keep the maintenance interval (Search) and to protect the engine from damage caused by poor lubrication, it is vitally important to make use of engine oil with the correct specification. Do not use oils which do not meet the following specifications or requirements. Use of unsuitable oil may lead to engine damage which is not covered by the Mazda Warranty.

Engine oil viscosity, or thickness, has an effect on fuel economy and cold-weather operation (starting and oil flow).

Low-viscosity engine oils can provide improved fuel economy and cold-weather performance.

When choosing an oil, consider the temperature range your vehicle will operate in before the next oil change.

Then select the recommended viscosity from the chart.

Using oils of viscosity besides those recommended for specific temperature ranges could result in engine damage.

(SKYACTIV-D 1.5 and SKYACTIV-D 2.2)

SKYACTIV-D 1.5 and SKYACTIV-D 2.2 use specified oil. Please confirm the specification in owner's manual. If engine oil other than the specified oil is used, the Diesel Particulate Filter effective period of use will be shortened or the Diesel Particulate Filter may be damaged.

Close Caution

View Caution

(MZR 1.6, SKYACTIV-G 1.5, SKYACTIV-G 2.0, and SKYACTIV-G 2.5)

It is normal for all engines to consume engine oil under normal driving conditions.

Engine oil consumption may be as high as 0.8 L/1,000 km (1 L/800 miles). This may be as a result of evaporation, internal ventilation or burning of the lubricating oil in the working engine. Oil consumption may be higher when the engine is new due to the running-in process. Oil consumption is also dependant on engine speed and engine load. Under extreme driving conditions, oil consumption may be higher.

(SKYACTIV-D 1.5 and SKYACTIV-D 2.2)

Whenever the engine oil is replaced, the vehicles engine control unit needs to be reset as soon as possible. Otherwise the wrench indicator light or engine oil warning light may turn on. To reset the engine control unit, consult an expert repairer, we recommend an Authorised Mazda Repairer or refer to the vehicle engine control unit reset procedure (Search).
Inspect the engine oil level periodically. When inspecting the engine oil, if the engine oil level is exceeds the “X” mark on the dipstick, replace the engine oil. This should be done by an expert repairer, we recommend an Authorised Mazda Repairer. When replacing the engine oil, inspect the oil level using the oil dipstick and refill so that the engine oil level is within the range between MIN and MAX as shown in the figure.

Close Note

View Note

Maintenance and Care Owner Maintenance Engine Oil

Vehicle Engine Control Unit Reset Procedure

This procedure is intended for vehicles with SKYACTIV-D 1.5 and SKYACTIV-D 2.2, and vehicles with SKYACTIV-G 1.5 or SKYACTIV-G 2.0 which have the engine oil flexible maintenance setting selected.

Close Note

View Note

After replacing the engine oil, have a repair shop such as an Authorised Mazda Repairer perform the initialization (engine oil data resetting) of the recorded value. If the value recorded by the computer is not initialized, the wrench indicator light may not turn off or it may turn on earlier than normal.

The initialization (engine oil data resetting) of the recorded value can be performed using the following procedure:

Switch the ignition OFF.
Switch the ignition ON with the selector pressed, and press and hold the selector for about 5 seconds until the master warning light flashes.
After the master warning light flashes for several seconds, the initialization is completed.

Close Note

View Note

Maintenance and Care Owner Maintenance Engine Oil

Inspecting Engine Oil Level

Be sure the vehicle is on a level surface.
Warm up the engine to normal operating temperature.
Turn it off and wait at least 5 minutes for the oil to return to the sump.
Pull out the dipstick, wipe it clean, and reinsert it fully.

MZR 1.6

SKYACTIV-G 1.5, SKYACTIV-G 2.0, and SKYACTIV-G 2.5

SKYACTIV-D 1.5

SKYACTIV-D 2.2

(SKYACTIV-D 1.5 and SKYACTIV-D 2.2)

When inspecting the engine oil level, pull out the dipstick straight without twisting. In addition, when inserting the dipstick, always insert it without twisting so that the “X” mark faces the front of the vehicle.

Close Note

View Note
Pull it out again and examine the level.

The level is normal if it is between the MIN and MAX marks.

If it is near or below MIN, add enough oil to bring the level to MAX.

Do not overfill the engine oil. This may cause engine damage.

Close Caution

View Caution
Make sure the O-ring on the dipstick is positioned properly before reinserting the dipstick.
Reinsert the dipstick fully.

Engine Coolant

Maintenance and Care Owner Maintenance Engine Coolant

Engine Coolant

Maintenance and Care Owner Maintenance Engine Coolant

Inspecting Coolant Level

Do not use a match or live flame in the engine compartment. DO NOT ADD COOLANT WHEN THE ENGINE IS HOT:

A hot engine is dangerous. If the engine has been running, parts of the engine compartment can become very hot. You could be burned. Carefully inspect the engine coolant in the coolant reservoir, but do not open it.

Pull over to a safe location, then switch the ignition off and make sure the fan is not running before attempting to work near the cooling fan:

Do not remove either cooling system cap when the engine and radiator are hot:

When the engine and radiator are hot, scalding coolant and steam may shoot out under pressure and cause serious injury.

Close Warning

View Warning

Changing the coolant should be done by an expert repairer, we recommend an Authorised Mazda Repairer.

Close Note

View Note

Inspect the antifreeze protection and coolant level in the coolant reservoir at least once a year―at the beginning of the winter season―and before travelling where temperatures may drop below freezing.

Inspect the condition and connections of all cooling system and heater hoses.

Replace any that are swollen or deteriorated.

The coolant should be at full in the radiator and between the F and L marks on the coolant reservoir when the engine is cool.

MZR 1.6, SKYACTIV-G 1.5, SKYACTIV-G 2.0, and SKYACTIV-G 2.5

SKYACTIV-D 1.5

SKYACTIV-D 2.2

If it is at or near L, add enough coolant to the coolant reservoir to provide freezing and corrosion protection and to bring the level to F.

Securely tighten the coolant reservoir tank cap after adding coolant.

Radiator coolant will damage paint.

Rinse it off quickly if spilled.

Use only soft (demineralised) water in the coolant mixture. Water that contains minerals will cut down on the coolant's effectiveness.
Do not add only water. Always add a proper coolant mixture.
The engine has aluminium parts and must be protected by an ethylene-glycol-based coolant to prevent corrosion and freezing.
DO NOT USE coolants Containing Alcohol, methanol, Borate or Silicate.

These coolants could damage the cooling system.
DO NOT MIX alcohol or methanol with the coolant. This could damage the cooling system.
Do not use a solution that contains more than 60% antifreeze.

This would reduce effectiveness.

If the “FL22” mark is shown on or near the cooling system cap, use of FL-22 is recommended when replacing engine coolant. Using engine coolant other than FL-22 may cause serious damage to the engine and cooling system.

Close Caution

View Caution

If the coolant reservoir is empty or new coolant is required frequently, consult an expert repairer, we recommend an Authorised Mazda Repairer.

Brake/Clutch Fluid

Maintenance and Care Owner Maintenance Brake/Clutch Fluid

Brake/Clutch Fluid

Maintenance and Care Owner Maintenance Brake/Clutch Fluid

Inspecting Brake/Clutch Fluid Level

If the brake/clutch fluid level is low, have the brakes inspected:

A low brake/clutch fluid level is dangerous.

A low level could indicate brake lining wear or a brake system leak which could cause the brakes to fail and lead to an accident.

Close Warning

View Warning

The brakes and clutch draw fluid from the same reservoir.

Inspect the fluid level in the reservoir regularly. It should be kept between the MAX and MIN lines.

The level normally drops with accumulated distance, a condition associated with wear of brake and clutch linings. If it is excessively low, have the brake/clutch system inspected by an expert repairer, we recommend an Authorised Mazda Repairer.

Left-hand drive model

Type A

Type B

Right-hand drive model

Automatic Transaxle Fluid (4-speed transaxle)

Window and Headlight Washer Fluid

Body Lubrication

Wiper Blades

Battery

Key Battery Replacement

Tyres

Light Bulbs

Fuses