Maintenance and CareOwner MaintenanceLight Bulbs

Light Bulbs

Headlights (High/Low beam)

Running lights

Headlights (Low beam)

Headlights (High beam)

Fog lights (Some Models)

Front direction indicator lights

Position lights

Side direction indicator lights

Brake lights (With LED headlights)

Tail lights (With LED headlights)

Brake lights/Tail lights (With halogen headlights)

Rear direction indicator lights

Tail lights (With LED headlights)

Reverse lights

High-mount brake light

Number plate lights

Overhead lights (Front)/Map lights

Vanity mirror lights (Some Models)

Overhead lights (Rear)

Boot light (Saloon)

Luggage compartment light (Hatchback)

 

Never touch the glass portion of a halogen bulb with your bare hands and always wear eye protection when handling or working around the bulbs:

When a halogen bulb breaks, it is dangerous. These bulbs contain pressurised gas. If one is broken, it will explode and serious injuries could be caused by the flying glass.

If the glass portion is touched with bare hands, body oil could cause the bulb to overheat and explode when lit.

Always keep halogen bulbs out of the reach of children:

Playing with a halogen bulb is dangerous. Serious injuries could be caused by dropping a halogen bulb or breaking it some other way.

Close Warning

 

When removing the lens or lamp unit using a flathead screwdriver, make sure that the flathead screwdriver does not contact the interior terminal. If the flathead screwdriver contacts the terminal, a short circuit may occur.

Close Caution

 

  • To replace the bulb, contact an expert repairer, we recommend an Authorised Mazda Repairer.

  • If the halogen bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used.

  • Use the protective cover and carton for the replacement bulb to dispose of the old bulb promptly and out of the reach of children.

Close Note
Maintenance and CareOwner MaintenanceLight Bulbs

Replacing Exterior Light Bulbs

Headlights (With LED headlights, Running lights/Position lights (With LED headlights), Fog lights (Some Models)

The LED bulb cannot be replaced as a single unit because it is an integrated unit.

The LED bulb has to be replaced with the unit. We recommend an Authorised Mazda Repairer when the replacement is necessary.

Headlights (With halogen headlights)

Low-beam bulbs

  1. If you are changing the right bulb, start the engine, turn the steering wheel all the way to the left, and turn off engine. If you are changing the left bulb, turn the steering wheel to the right, and turn off engine.

  2. Make sure the headlight switch is off.

  3. Pull the centre of each plastic retainer and remove the retainers.

     

  4. Turn the screw anticlockwise and remove it, and then partially peel back the mudguard.

     

  5. Disconnect the connector from the unit by pressing the tab on the connector with your finger and pulling the connector downward.

     

  6. Turn the socket and bulb assembly to remove it. Carefully remove the bulb from its socket in the reflector by gently pulling it straight backward out of the socket.

     

  7. Install the new bulb in the reverse order of the removal procedure.

High-beam bulbs

  1. Make sure the ignition is switched off, and the headlight switch is off.

  2. Lift the bonnet.

  3. Disconnect the connector from the unit by pressing the tab on the connector with your finger and pulling the connector downward.

     

  4. Turn the socket and bulb assembly to remove it. Carefully remove the bulb from its socket in the reflector by gently pulling it straight backward out of the socket.

     

  5. Install the new bulb in the reverse order of the removal procedure.

Front direction indicator lights, Position lights (With halogen headlights)

  1. If you are changing the right bulb, start the engine, turn the steering wheel all the way to the left, and turn off engine. If you are changing the left bulb, turn the steering wheel to the right, and turn off engine.

  2. Make sure the headlight switch is off.

  3. Pull the centre of each plastic retainer and remove the retainers.

     

  4. Turn the screw anticlockwise and remove it, and then partially peel back the mudguard.

     

  5. (Front direction indicator lights)

    Disconnect the connector from the unit by pressing the tab on the connector with your finger and pulling the connector.

     

  6. Turn the socket and bulb assembly anticlockwise and remove it.

  7. Disconnect the bulb from the socket.

    Front direction indicator lights

     

    Position lights (With halogen headlights)

     

  8. Install the new bulb in the reverse order of the removal procedure.

Side direction indicator lights, Brake lights (With LED headlights), Tail lights (With LED headlights), High-mount brake light

The LED bulb cannot be replaced as a single unit because it is an integrated unit.

The LED bulb has to be replaced with the unit. We recommend an Authorised Mazda Repairer when the replacement is necessary.

Rear direction indicator lights, Brake lights/Tail lights (With halogen headlights)

Saloon

  1. Make sure the ignition is switched off, and the headlight switch is off.

  2. Pull the centre of each plastic retainer and remove the retainers.

  3. Remove boot end trim.

     

  4. Pull the centre of each plastic retainer and remove the retainers.

  5. Peel back the boot side trim.

     

  6. Turn the socket and bulb assembly anticlockwise and remove it.

    Rear direction indicator lights

     

    Brake lights/Tail lights (With halogen headlights)

     

  7. Disconnect the connector from the unit by pressing the tab on the connector with your finger and pulling the connector.

    Rear direction indicator lights

     

    Brake lights/Tail lights (With halogen headlights)

     

  8. Disconnect the bulb by pulling it out.

    Rear direction indicator lights, Brake lights/Tail lights (With halogen headlights)

     

  9. Install the new bulb in the reverse order of the removal procedure.

Hatchback

(Left side)

  1. Make sure the ignition is switched off, and the headlight switch is off.

  2. Remove the cover.

     

  3. Turn the socket and bulb assembly anticlockwise and remove it.

    Rear direction indicator lights

     

    Brake lights/Tail lights (With halogen headlights)

     

  4. Disconnect the connector from the unit by pressing the tab on the connector with your finger and pulling the connector.

    Rear direction indicator lights

     

    Brake lights/Tail lights (With halogen headlights)

     

  5. Disconnect the bulb by pulling it out.

    Rear direction indicator lights, Brake lights/Tail lights (With halogen headlights)

     

  6. Install the new bulb in the reverse order of the removal procedure.

  7. Insert the cover tabs and install the cover.

     

     

    Verify that the cover is securely installed.

    Close Note

(Right side)

  1. Make sure the ignition is switched off, and the headlight switch is off.

  2. Turn the knob and remove the cover.

     

  3. Turn the wing bolt and jack screw anticlockwise.

     

  4. Remove the jack

  5. Turn the socket and bulb assembly anticlockwise and remove it.

    Rear direction indicator lights

     

    Brake lights/Tail lights (With halogen headlights)

     

  6. Disconnect the connector from the unit by pressing the tab on the connector with your finger and pulling the connector.

    Rear direction indicator lights

     

    Brake lights/Tail lights (With halogen headlights)

     

  7. Disconnect the bulb by pulling it out.

    Rear direction indicator lights, Brake lights/Tail lights (With halogen headlights)

     

  8. Install the new bulb.

  9. Insert the wing bolt into the jack with the jack screw pointing to the down and turn the wing bolt clockwise to temporarily tighten it.

  10. Turn the jack screw in the direction shown in the figure.

     

  11. Turn the wing bolt completely to secure the jack.

     

    If the jack is not completely secured, it could rattle while driving. Make sure the jack screw is sufficiently tightened.

    Close Note

  12. Install the cover in the reverse order of the removal procedure.

  13. Insert the cover tabs and install the cover.

     

     

    Verify that the cover is securely installed.

    Close Note

Reverse lights

Saloon

  1. Make sure the ignition is switched off, and the headlight switch is off.

  2. Pull the centre of each plastic retainer and remove the retainers.

  3. Peel back the boot lid trim.

     

  4. Disconnect the electrical connector from the bulb by pressing the tab on the connector with your finger and pulling the connector.

     

  5. Turn the socket and bulb assembly anticlockwise and remove it.

  6. Disconnect the bulb from the socket.

     

  7. Install the new bulb in the reverse order of the removal procedure.

Hatchback

  1. Make sure the ignition is switched off, and the headlight switch is off.

  2. Remove the cover.

     

  3. Disconnect the electrical connector from the bulb by pressing the tab on the connector with your finger and pulling the connector.

     

  4. Turn the socket and bulb assembly anticlockwise and remove it.

  5. Disconnect the bulb from the socket.

     

  6. Install the new bulb in the reverse order of the removal procedure.

Number plate lights

Saloon

  1. Make sure the ignition is switched off, and the headlight switch is off.

  2. Pull the centre of each plastic retainer and remove the retainers.

  3. Peel back the boot lid trim.

     

  4. Disconnect the connector from the unit by pressing the tab on the connector with your finger and pulling the connector.

     

  5. Turn the socket and bulb assembly anticlockwise and remove it.

  6. Disconnect the bulb from the socket.

     

  7. Install the new bulb in the reverse order of the removal procedure.

Hatchback

  1. Make sure the ignition is switched off, and the headlight switch is off.

  2. Wrap a flathead screwdriver with a soft cloth to prevent damage to the lens, and then remove the lens by carefully prying on the edge of the lens with a flathead screwdriver.

  3. Disconnect the bulb by pulling it out.

     

  4. Install the new bulb in the reverse order of the removal procedure.

Maintenance and CareOwner MaintenanceLight Bulbs

Replacing Interior Light Bulbs

Overhead lights (Front)/Map lights, Overhead lights (Rear), Vanity mirror lights (Some Models)

  1. Wrap a small flathead screwdriver with a soft cloth to prevent damage to the lens, and then remove the lens by carefully prying on the edge of the lens with the flathead screwdriver.

  2. Disconnect the bulb by pulling it out.

    Overhead lights (Front)/Map lights

     

     

    Overhead lights (Rear)

     

    Vanity mirror lights (Some Models)

     

  3. Install the new bulb in the reverse order of the removal procedure.

Boot light (Saloon)

  1. Press both sides of the lens cap to remove it.

  2. Disconnect the bulb by pulling it out.

     

  3. Install the new bulb in the reverse order of the removal procedure.

Luggage compartment light (Hatchback)

  1. Wrap a small flathead screwdriver with a soft cloth to prevent damage to the lens and remove the lens by carefully prying on the edge of the lens with the flathead screwdriver.

     

  2. Disconnect the connector from the unit by pressing the tab on the connector with your finger and pulling the connector.

     

  3. Disconnect the bulb by pulling it out.

     

  4. Install the new bulb in the reverse order of the removal procedure.