Instrument Cluster and Display
Meters and Gauges
Speedometer
The speedometer indicates the speed of the vehicle.
Speed Unit Selector (Type A instrument cluster) (Some Models)
In some countries, you may have to change the speed units between km/h and mph.
Press the speed unit selector for 1.5 seconds or more.
The speed units for the speedometer will change between km/h and mph.
Odometer, Trip Meter and Trip Meter Selector
The display mode can be changed from odometer to trip meter A to trip meter B and then back to odometer by pressing the selector while one of them is displayed. The selected mode will be displayed.
Type A/Type B
Type C
When the ignition is switched to ACC or off, the odometer or trip meters cannot be displayed, however, pressing the selector can inadvertently switch the trip meters or reset them during an approximate ten-minute period in the following cases:
-
After the ignition is switched to off from ON.
-
After the driver's door is opened.
Odometer
The odometer records the total distance the vehicle has been driven.
Trip meter
The trip meter can record the total distance of two trips. One is recorded in trip meter A, and the other is recorded in trip meter B.
For instance, trip meter A can record the distance from the point of origin, and trip meter B can record the distance from where the fuel tank is filled.
When trip meter A is selected, pressing the selector again within one second will change to trip meter B mode.
When trip meter A is selected, TRIP A will be displayed. When trip meter B is selected, TRIP B will be displayed.
The trip meter records the total distance the vehicle is driven until the meter is again reset. Return it to “0.0” by depressing and holding the selector for one second or more. Use this meter to measure trip distances and to compute fuel consumption.
-
(Vehicles with type B audio)
If the fuel economy data is reset using the fuel economy monitor, or trip A is reset using the trip meter when the function which synchronizes the fuel economy monitor and the trip meter is on, the fuel economy data and trip A are reset simultaneously.
Refer to Fuel Economy Monitor (Search).
-
Only the trip meters record tenths of kilometres (miles).
-
The trip record will be erased when:
-
The power supply is interrupted (blown fuse or the battery is disconnected).
-
The vehicle is driven over 9999.9 km (mile).
-
Tachometer (Some Models)
The tachometer shows engine speed in thousands of revolutions per minute (rpm).
Do not run the engine with the tachometer needle in the RED ZONE.
This may cause severe engine damage.
Type A
Type B
When the tachometer needle enters the STRIPED ZONE, this indicates to the driver that the gears should be shifted before entering the RED ZONE.
Fuel Gauge (Without Multi-information display)
The fuel gauge shows approximately how much fuel is remaining in the tank when the ignition is switched ON. We recommend keeping the tank over 1/4 full.
Type A
Type C
If the low fuel warning light illuminates or the fuel level is very low, refuel as soon as possible.
Refer to Taking Action (Search) .
-
After refuelling, it may require some time for the indicator to stabilize. In addition, the indicator may deviate while driving on a slope or curve since the fuel moves in the tank.
-
The display indicating a quarter or less remaining fuel has more segments to show the remaining fuel level in greater detail.
-
The direction of the arrow (
) indicates that the fuel-filler flap is on the left side of the vehicle.
(SKYACTIV-D 1.5, SKYACTIV-D 2.2)
If inconsistency in engine performance or stalling occurs due to low fuel level conditions, refuel the vehicle as soon as possible and add at least 10 L (2.7 US gal, 2.2 Imp gal) of fuel.
Instrument Panel Illumination
(Without auto-light control)
When the position lights are turned on with the ignition switched ON, the brightness of the instrument panel illumination is dimmed.
(With auto-light control)
When the position lights are turned on with the ignition switched ON, the brightness of the instrument panel illumination is dimmed. However, when the light sensor detects that the surrounding area is bright such as when the position lights are turned on in the daytime, the instrument panel illumination does not dim.
-
(With auto-light control)
When the ignition is switched ON in the early evening or at dusk, the instrument panel illumination is dimmed for several seconds until the light sensor detects the brightness of the surrounding area, however, the dimmer may cancel after the brightness is detected.
-
When the position lights are turned on, the position lights indicator light in the instrument cluster turns on.
Refer to Headlights (Search).
The brightness of the instrument cluster and instrument panel illuminations can be adjusted by rotating the knob.
-
The brightness decreases by rotating the knob to the left. A beep sound will be heard when the knob has been rotated to the maximum dim position.
-
The brightness increases by rotating the knob to the right.
Function for cancelling illumination dimmer
The illumination dimmer can be cancelled by rotating the instrument panel illumination knob to the right until a beep sound is heard while the instrument cluster is dimmed with the ignition switched ON. If the instrument cluster's visibility is reduced due to glare from surrounding brightness, cancel the illumination dimmer.
-
When the illumination dimmer is cancelled, the instrument cluster cannot be dimmed even if the position lights are turned on.
-
When the illumination dimmer is cancelled, the screen in the centre display switches to constant display of the daytime screen.
Outside Temperature Display (Without Multi-information display) (Some Models)
When the ignition is switched ON, the outside temperature is displayed.
-
Under the following conditions, the outside temperature display may differ from the actual outside temperature depending on the surroundings and vehicle conditions:
-
Significantly cold or hot temperatures.
-
Sudden changes in outside temperature.
-
The vehicle is parked.
-
The vehicle is driven at low speeds.
-
Changing the Temperature Unit of the Outside Temperature Display (Vehicles with Type B audio)
The outside temperature unit can be switched between Celsius and Fahrenheit.
Settings can be changed by operating the centre display screen.
Refer to Personalisation Features (Search).
When the temperature unit indicated in the outside temperature display is changed, the temperature unit indicated in the engine coolant gauge display changes in conjunction with it.
Outside Temperature Warning (Some Models)
When the outside temperature is low, the indication flashes and a beep sound is heard to warn the driver of the possibility of icy roads.
If the outside temperature is lower than about 4 °C (39 °F), the outside temperature display and the 
mark flashes for about ten seconds and a beep sound is heard once.
If the outside temperature is lower than -20 °C (-4 °F), the beep sound does not operate. However, the mark illuminates.
Cruise Control Set Vehicle Speed Display (Without Multi-information display) (Some Models)
The vehicle speed preset using the cruise control is displayed.
Trip Computer and INFO Switch (Without Multi-information Display) (Some Models)
The following information can be selected by pressing the INFO switch with the ignition switched ON.
-
Distance-to-empty mode
-
Average fuel economy mode
-
Current fuel economy mode
-
Average vehicle speed mode
-
Vehicle speed alarm mode (Some Models)
If you have any problems with your trip computer, consult an expert repairer, we recommend an Authorised Mazda Repairer.
Distance-to-empty mode
This mode displays the approximate distance you can travel on the remaining fuel based on the fuel economy.
The distance-to-empty will be calculated and displayed every second.
(European model)
(Except European model)
-
Even though the distance-to-empty display may indicate a sufficient amount of remaining driving distance before refuelling is required, refuel as soon as possible if the fuel level is very low or the low fuel warning light illuminates.
-
The display may not change unless you add more than approximately 9 L (2.3 US gal, 1.9 Imp gal) of fuel.
-
The distance-to-empty is the approximate remaining distance the vehicle can be driven until all the graduation marks in the fuel gauge (indicating the remaining fuel supply) disappear.
-
If there is no past fuel economy information such as after first purchasing your vehicle or the information is deleted when the battery leads are disconnected, the actual distance-to empty/range may differ from the amount indicated.
Average fuel economy mode
This mode displays the average fuel economy by calculating the total fuel consumption and the total travelled distance since purchasing the vehicle, re-connecting the battery after disconnection, or resetting the data. The average fuel economy is calculated and displayed every minute.
(European model)
(Except European model)
To clear the data being displayed, press the INFO switch for more than 1.5 seconds.
After pressing the INFO switch, - - - L/100 km (- - - mpg) or - - - km/L will be displayed for about 1 minute before the fuel economy is recalculated and displayed.
Current fuel economy mode
This mode displays the current fuel economy by calculating the amount of fuel consumption and the distance travelled.
Current fuel economy will be calculated and displayed every 2 seconds.
(European model)
(Except European model)
When you have slowed the vehicle to about 5 km/h (3 mph), - - - L/100 km (- - - mpg) or - - - km/L will be displayed.
Average vehicle speed mode
This mode displays the average vehicle speed by calculating the distance and the time travelled since connecting the battery or resetting the data.
Average vehicle speed will be calculated and displayed every 10 seconds.
(European model)
(Except European model)
To clear the data being displayed, press the INFO switch for more than 1.5 seconds. After pressing the INFO switch, - - - km/h (- - - mph) will be displayed for about 1 minute before the vehicle speed is recalculated and displayed.
Vehicle speed alarm mode (Some Models)
In this mode, the current setting for the vehicle speed alarm is displayed. You can change the vehicle speed setting at which the warning is triggered.
The vehicle speed alarm display is activated at the same time the beep sound is heard. The set vehicle speed flashes several times.
The vehicle speed alarm can be set using the INFO switch.
-
Always set the vehicle speed according to the laws and regulations of the country/city in which the vehicle is driven. In addition, always verify the speed of the vehicle using the speedometer.
-
The vehicle speed alarm function can be set between 30 and 250 km/h (20 and 150 mph).
Multi-information Display (Some Models)
The multi-information display indicates the following information.
-
Fuel gauge
-
Outside temperature
-
Distance-to-empty
-
Average fuel economy
-
Current fuel economy
-
Lane Departure Warning System (LDWS) Display
-
Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) Display
-
Cruise Control Display
-
Warning message
The screen content changes each time the INFO switch is pressed.
Fuel Gauge
Outside Temperature Display
When the ignition is switched ON, the outside temperature is displayed.
-
Under the following conditions, the outside temperature display may differ from the actual outside temperature depending on the surroundings and vehicle conditions:
-
Significantly cold or hot temperatures.
-
Sudden changes in outside temperature.
-
The vehicle is parked.
-
The vehicle is driven at low speeds.
-
Changing the Temperature Unit of the Outside Temperature Display
The outside temperature unit can be switched between Celsius and Fahrenheit using the following procedure.
(Vehicles with Type B audio)
Settings can be changed by operating the centre display screen.
Refer to Personalisation Features (Search).
(Vehicles without Type B audio)
-
Press the INFO switch with the ignition switched off and continue pressing the INFO switch for 5 seconds or longer while switching the ignition ON. The outside temperature display flashes.
-
Press the INFO switch to change the outside temperature unit.
-
Press and hold the INFO switch for 3 seconds or longer while the outside temperature display is flashing. The outside temperature display illuminates.
When the temperature unit indicated in the outside temperature display is changed, the temperature unit indicated in the engine coolant gauge display changes in conjunction with it.
Outside Temperature Warning (Some Models)
When the outside temperature is low, the indication flashes and a beep sound is heard to warn the driver of the possibility of icy roads.
If the outside temperature is lower than about 4 °C (39 °F), the outside temperature display and the mark flashes for about ten seconds and a beep sound is heard once.
If the outside temperature is lower than -20 °C (-4 °F), the beep sound does not operate. However, the mark illuminates.
Distance-to-empty Mode
This displays the approximate distance you can travel on the remaining fuel based on the fuel economy.
The distance-to-empty will be calculated and displayed every second.
-
Even though the distance-to-empty display may indicate a sufficient amount of remaining driving distance before refuelling is required , refuel as soon as possible if the fuel level is very low or the low fuel warning light illuminates.
-
The display will not change unless you add more than approximately 9 L (2.3 US gal, 1.9 Imp gal) of fuel.
-
The distance-to-empty is the approximate remaining distance the vehicle can be driven until all the graduation marks in the fuel gauge indicating the remaining fuel supply disappear.
-
If there is no past fuel economy information such as after first purchasing your vehicle or the information is deleted when the battery leads are disconnected, the actual distance-to empty/range may differ from the amount indicated.
Average Fuel Economy Mode
This mode displays the average fuel economy by calculating the total fuel consumption and the total travelled distance since purchasing the vehicle, re-connecting the battery after disconnection, or resetting the data.
The average fuel economy is calculated and displayed every minute.
To clear the data being displayed, press the INFO button for more than 1.5 seconds. After pressing the INFO button, - - - L/100 km (- - - mpg) will be displayed for about 1 minute before the fuel economy is recalculated and displayed.
Current Fuel Economy Mode
This displays the current fuel economy by calculating the amount of fuel consumption and the distance travelled.
Current fuel economy will be calculated and displayed every two seconds.
When you've slowed to about 5 km/h (3 mph), - - - L/100 km (- - - mpg) will be displayed.
Lane Departure Warning System (LDWS) Display (Some Models)
Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) Display (Some Models)
Displays the system status.
Refer to Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) (Search).
Cruise Control Set Vehicle Speed Display (Some Models)
Warning (Display Indication)
A message is displayed to notify the user of the system operation status and malfunctions or abnormalities.
If the warning light turns on/flashes simultaneously or a symbol is indicated in the display, check the information regarding the warning light or symbol. (Search)
When only a message is displayed, refer to Message Indicated in Multi-information Display. (Search)
Active Driving Display (Some Models)
Always adjust the display brightness and position with the vehicle stopped:
Adjusting the display brightness and position while driving the vehicle is dangerous as doing so could distract your attention from the road ahead and lead to an accident.
-
Do not try to adjust the angle or open/close the active driving display manually. Fingerprints on the display will make it difficult to view and using excessive force when operating it could cause damage.
-
Do not place objects in the vicinity of the active driving display. The active driving display may not operate or any interference with its operation could cause damage.
-
Do not place beverages near the active driving display. If water or other liquids are splashed on the active driving display, it could cause damage.
-
Do not place objects above the active driving display or apply stickers to the dust-proof sheet/optical receiver as they will cause interference.
-
A sensor is integrated to control the display's luminosity. If the optical receiver is covered, the display's luminosity will lower making the display difficult to view.
-
Do not allow intense light to hit the optical receiver. Otherwise, it could cause damage.
-
Wearing polarized sunglasses will reduce the visibility of the active driving display due to the characteristics of the display.
-
If the battery has been removed and re-installed or the battery voltage is low, the adjusted position may deviate.
-
The display may be difficult to view or temporarily affected by weather conditions such as rain, snow, light, and temperature.
-
If the audio system is removed, the active driving display cannot be operated.
The active driving display indicates the following information:
-
Blind Spot Monitoring (BSM) Operation Conditions and Warnings
Refer to Blind Spot Monitoring (BSM) (Search).
-
Distance Recognition Support System (DRSS) Warnings
Refer to Distance Recognition Support System (DRSS) (Search).
-
Traffic Sign Recognition System (TSR) traffic signs and Warnings
Refer to Traffic Sign Recognition System (TSR) (Search).
-
Mazda Radar Cruise Control (MRCC) Operation Conditions and Warnings
Refer to Mazda Radar Cruise Control (MRCC) (Search).
-
Lane Departure Warning System (LDWS) Warnings
Refer to Lane Departure Warning System (LDWS) (Search).
-
Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) Operation Conditions and Warnings
Refer to Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) (Search).
-
Advanced Smart City Brake Support (Advanced SCBS) Warnings
Refer to Advanced Smart City Brake Support (Advanced SCBS) (Search).
-
Smart City Brake Support [Forward] (SCBS F) Warnings
Refer to Smart City Brake Support [Forward] (SCBS F) (Search).
-
Smart City Brake Support [Reverse] (SCBS R) Operation Conditions
Refer to Smart City Brake Support [Reverse] (SCBS R) (Search).
-
Smart Brake Support (SBS) Warnings
Refer to Smart Brake Support (SBS) (Search).
-
Adjustable Speed Limiter (ASL) Operation Conditions and Warnings
Refer to Adjustable Speed Limiter (ASL) (Search).
-
Driver Attention Alert (DAA) Warnings
Refer to Driver Attention Alert (DAA) (Search).
-
Cruise Control Operation Conditions
Refer to Cruise Control (Search).
-
Navigation Guidance (vehicles with navigation system)
-
Speed limit indicator (vehicles with navigation system)
-
Vehicle Speed
Each setting/adjustment for the active driving display can be performed on the centre display.
-
Select the
icon on the home screen and display the Settings screen. -
Select the AD-Disp tab.
-
Select the desired item and perform the setting/adjustment.
-
Method for adjusting screen brightness (automatically/manually)
-
Screen brightness initial settings (automatic adjustment is selected)
-
Screen brightness adjustment (manual adjustment is selected)
-
Display position of active driving display (display height)
-
Active driving display ON/OFF (indication)
-
Navigation guidance ON/OFF
-
Reset settings (reset)
-
Warning/Indicator Lights
Instrument Cluster varies depending on model and specifications.
Warning Lights
These lights turn on or flash to notify the user of the system operation status or a system malfunction.
|
Signal |
Warning |
Page |
|---|---|---|
 |
Brake System Warning Light*1*2 |
(Search) |
 |
ABS Warning Light*1 |
Electronic Brake Force Distribution System Warning (Search) |
|
ABS warning (Search) |
||
 |
Charging System Warning Light*1 |
(Search) |
 |
Engine Oil Warning Light*1 |
(Search) |
 (Red) |
High Engine Coolant Temperature Warning Light*1 |
(Search) |
 |
Power Steering Malfunction Indicator Light*1 |
(Search) |
 |
Master Warning Light*1 |
(Search) |
 |
Electric Parking Brake (EPB) Warning Light*1 (Some Models) |
(Search) |
 |
Check Engine Light*1 |
(Search) |
 (Amber) |
i-stop Warning Light*1 (Some Models) |
(Search) |
 |
Automatic Transaxle Warning Light*1 (Some Models) |
(Search) |
 |
Air Bag/Seat Belt Pretensioner System Warning Light*1 |
(Search) |
 |
Tyre Pressure Monitoring System Warning Light*1 (Some Models) |
Flashing (Search) |
|
Turns on (Search) |
||
 (Red) |
KEY Warning Light*1 |
Turns on (Search) |
|
Flashing (Search) |
||
 (Amber) |
High Beam Control System (HBC) Warning Light*1 (Some Models) |
(Search) |
|
Adaptive LED Headlights (ALH) Warning Light*1 (Some Models) |
(Search) | |
 (Amber) |
Mazda Radar Cruise Control (MRCC) Warning Light (Some Models) |
(Search) |
 |
Lane Departure Warning System (LDWS) Warning Light*1 (Some Models) |
Turns on (Search) |
|
Flashing (Search) |
||
|
Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) Warning Light*1 (Some Models) |
Turns on (Search) |
|
|
Flashing (Search) |
||
 |
LED Headlight Warning Light*1 (Some Models) |
(Search) |
 (Amber) |
Smart Brake Support/Smart City Brake Support (SBS/SCBS) Warning Light*1 (Some Models) |
(Search) |
 |
Low Fuel Warning Light |
(Search) |
 |
120 km/h Warning Light*1 (Some Models) |
(Search) |
 |
Seat Belt Warning Light (Front seat) |
(Search) |
 (Red) |
Seat Belt Warning Light (Rear seat) |
(Search) |
 |
Low Washer Fluid Level Warning Light (Some Models) |
(Search) |
 |
Door-Ajar Warning Light |
(Search) |
-
The light turns on when the ignition is switched on for an operation check, and turns off a few seconds later or when the engine is started. If the light does not turn on or remains turned on, have the vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.
-
The light turns on continuously when the parking brake is applied. (Without Electric Parking Brake (EPB))
Indication/Indicator Lights
These lights turn on or flash to notify the user of the system operation status or a system malfunction.
|
Signal |
Indicator Lights |
Page |
|---|---|---|
 (Green) |
KEY Indicator Light |
(Search) |
 |
Security Indicator Light*1 |
(Search) |
 |
Vehicle Speed Alarm Indication (Some Models) |
(Search) |
 |
Glow Indicator Light*1 (Some Models) |
(Search) |
 |
Diesel Particulate Filter Indicator Light*1 (Some Models) |
(Search) |
 |
Wrench Indicator Light*1 |
(Search) |
 (Blue) |
Low Engine Coolant Temperature Indicator Light |
(Search) |
 (Green) |
i-stop Indicator Light (Some Models) |
(Search) |
 |
i-ELOOP Indicator Light (Some Models) |
(Search) |
 |
Shift Position Indication (Some Models) |
(Search) |
 |
Lights-On Indicator Light |
(Search) |
 |
Headlight High-Beam Indicator Light |
Headlight High-Low Beam (Search) |
|
Flashing the Headlights (Search) |
||
 |
Direction Indicator/Hazard Warning Indicator Lights |
Turn and Lane-Change Signals (Search) |
|
Hazard Warning Flasher (Search) |
||
 |
Front Fog Light Indicator Light (Some Models) |
(Search) |
 |
Rear Fog Light Indicator Light (Some Models) |
(Search) |
 |
Electric Parking Brake (EPB) Indicator Light*1*2 (Some Models) |
(Search) |
 |
Brake Pedal Operation demand Indicator Light (Some Models) |
(Search) |
 |
TCS/DSC Indicator Light*1 (Some Models) |
Traction Control System (TCS) (Search) |
|
Dynamic Stability Control (DSC) (Search) |
||
|
Turns on (Search) |
||
 |
DSC OFF Indicator Light*1 (Some Models) |
(Search) |
 |
Select Mode Indicator Light (Some Models) |
(Search) |
 (Green) |
High Beam Control System (HBC) Indicator Light (Some Models) |
(Search) |
|
Adaptive LED Headlights (ALH) Indicator Light (Some Models) |
(Search) | |
 |
Blind Spot Monitoring (BSM) OFF Indicator Light*1 (Some Models) |
Except malfunction (Search) |
|
Malfunction (Search) |
||
 |
Lane Departure Warning System (LDWS) OFF Indicator Light*1 (Some Models) |
(Search) |
|
Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) OFF Indicator Light*1 (Some Models) |
(Search) | |
 (Green) |
Mazda Radar Cruise Control (MRCC) Indicator Light (Some Models) |
(Search) |
 (Red) |
Smart Brake Support/Smart City Brake Support (SBS/SCBS) Indicator Light (Some Models) |
Advanced Smart City Brake Support (Advanced SCBS) (Search) |
|
Smart City Brake Support [Forward] (SCBS F) (Search) |
||
|
Smart City Brake Support [Reverse] (SCBS R) (Search) |
||
|
Smart Brake Support (SBS) (Search) |
||
 |
Smart Brake Support/Smart City Brake Support (SBS/SCBS) OFF Indicator Light (Some Models) |
Advanced Smart City Brake Support (Advanced SCBS) (Search) |
|
Smart City Brake Support [Forward] (SCBS F) (Search) |
||
|
Smart City Brake Support [Reverse] (SCBS R) (Search) |
||
|
Smart Brake Support (SBS) (Search) |
||
 (Green) |
Seat Belt Indicator Light (Rear seat) (Some Models) |
(Search) |
 (White) |
Cruise Main Indication (Some Models) |
(Search) |
 (White/Green) |
Cruise Set Indication/Indicator Light (Some Models) |
(Search) |
 (White) |
Adjustable Speed Limiter (ASL) Main Indication (Some Models) |
(Search) |
 (White/Green) |
Adjustable Speed Limiter (ASL) Set Indication/Indicator Light (Some Models) |
(Search) |
-
The light turns on when the ignition is switched on for an operation check, and turns off a few seconds later or when the engine is started. If the light does not turn on or remains turned on, have the vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.
-
The light turns on continuously when the parking brake is applied. (With Electric Parking Brake (EPB))
Wrench Indicator Light (Some Models)
When the ignition is switched ON, the wrench indicator light is illuminated and then turns off after a few seconds.
When illuminated
The wrench indicator light turns on when the preset maintenance period arrives. Verify the content and perform maintenance.
Refer to Maintenance Monitor (Search).
(SKYACTIV-D 1.5)
The wrench indicator light turns on under the following conditions:
-
The engine oil has deteriorated.
-
The engine oil level is around the MIN mark on the dipstick or it is less than the MIN mark. (Some Models)
-
The engine oil level is around the X mark on the dipstick or it exceeds the X mark. (Some Models)
Check the engine oil. Refer to Inspecting Engine Oil Level (Search).
Replace the engine oil if the wrench indicator light does not turn off even though the engine oil level is in the normal range.
-
Depending on the vehicle use conditions, the wrench indicator light may turn on for reasons other than the preset maintenance period.
-
Whenever the engine oil is replaced, a reset of the vehicle engine control unit necessary.
Your Authorised Mazda Repairer will be able to reset the engine control unit or see (Search) for the Vehicle engine control unit reset procedure.
When flashing (SKYACTIV-D 1.5, SKYACTIV-D 2.2)
The sedimentor separates water from the fuel.
If water accumulates in this filter, the warning light will flash. When it does, consult an expert repairer, we recommend an Authorised Mazda Repairer as soon as possible.
Low Engine Coolant Temperature Indicator Light (Blue)
The light illuminates continuously when the engine coolant temperature is low and turns off after the engine is warm.
If the low engine coolant temperature indicator light remains illuminated after the engine has been sufficiently warmed up, the temperature sensor could have a malfunction. Consult an expert repairer, we recommend an Authorised Mazda Repairer.
Glow Indicator Light (SKYACTIV-D 1.5, SKYACTIV-D 2.2)
When the ignition is switched ON, the glow indicator light turns on. The glow indicator light turns off when preheating is finished.
A problem in the system might be indicated under the following conditions. Have your vehicle inspected by an expert repairer, we recommend an Authorised Mazda Repairer.
-
The glow indicator light does not turn on when the ignition is switched ON or it remains on.
-
The glow indicator light is flashing.
If the vehicle is left with the ignition switched ON without starting the engine and a long period of time has elapsed since preheating finished, the preheating may be performed again and the glow indicator light may turn on.
