Instrument Cluster and Display

The speedometer indicates the speed of the vehicle.

The tachometer shows engine speed in thousands of revolutions per minute (rpm).

 

---

Do not run the engine with the tachometer needle in the RED ZONE.

This may cause severe engine damage.

 

1. STRIPED ZONE^*1

2. RED ZONE^*1

1. The range varies depending on the type of gauge.

Close Caution

View Caution

 

---

When the tachometer needle enters the STRIPED ZONE, this indicates to the driver that the gears should be shifted before entering the RED ZONE.

Close Note

View Note

1. Multi-information Display

2. INFO switch

The multi-information display indicates the following information.

• Speedometer

• Odometer

• Trip meter

• Outside temperature

• Distance-to-empty

• Average fuel economy

• Current fuel economy

• i-ACTIVSENSE Display

• Vehicle Speed Alarm

• Door-Ajar/Boot lid-Ajar/Liftgate-Ajar Warning Indication^*1

• Warning message

1. Displayed when opening door/boot lid/liftgate.

The screen content changes each time the INFO switch is pressed.

1. Basic display

2. Drive information display

3. i-ACTIVSENSE display

4. Warning message display^*1

1. Displayed only when a warning occurs.

The type of display for the fuel economy and the maximum driving distance can be changed.

Refer to the Settings section in the MZD Connect Owner's Manual.

You can switch between the odometer and trip meter display using the TRIP switch.

1. TRIP switch

2. Odometer display

3. Trip meter A display

4. Trip meter B display

Odometer

The odometer records the total distance the vehicle has been driven.

Trip meter

The driving distance for a specified interval is indicated. Two types (TRIP A, TRIP B) of interval distance and the average fuel economy for each can be measured.

For instance, trip meter A can record the distance from the point of origin, and trip meter B can record the distance from where the fuel tank is filled.

When trip meter A is selected, TRIP A will be displayed. When trip meter B is selected, TRIP B will be displayed.

The trip meter and average fuel economy can be reset by pressing the TRIP switch for 1.5 seconds or more while in each mode.

 

---

• Only the trip meters record tenths of kilometres (miles).

• The trip record will be erased when:

  • The power supply is interrupted (blown fuse or the battery is disconnected).

  • The vehicle is driven over 9999.9 km (mile).

Close Note

View Note

Displays the system status.

• Refer to Lane Departure Warning System (LDWS) (Search).

• Refer to Blind Spot Monitoring (BSM) (Search).

• Refer to Traffic Sign Recognition System (TSR) (Search).

• Refer to Distance & Speed Alert (DSA) (Search).

• Refer to Driver Attention Alert (DAA) (Search).

• Refer to Driver Monitoring (DM) (Search).

• Refer to Front Cross Traffic Alert (FCTA) (Search).

• Refer to Mazda Radar Cruise Control (MRCC) (Search).

• Refer to Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) (Search).

• Refer to Cruising & Traffic Support (CTS) (Search).

• Refer to Lane-keep Assist System (LAS) (Search).

• Refer to Intelligent Speed Assistance (ISA) (Search).

• Refer to Smart Brake Support (SBS) (Search).

• Refer to Smart Brake Support [Rear] (SBS-R) (Search).

• Refer to Smart Brake Support [Rear Crossing] (SBS-RC) (Search).

• Refer to Cruise Control (Search).

These lights turn on or flash to notify the user of the system operation status or a system malfunction.

Signal	Indicator	Refer to
(Green)	Seat Belt Indicator Light (Rear seat)	(Search)
	Front Passenger Air Bag Deactivation Indicator Light	(Search)
	Security Indicator Light	Immobilizer System (Search)
		Malfunction (Search)
(Green)	KEY Indicator Light	(Search)
(Green)	i-stop Indicator Light	(Search)
	Wrench Indication/Indicator Light*1	(Search)
	Shift Position Indication (Some Models)	(Search)
	Lights-On Indicator Light	(Search)
	Headlight High-Beam Indicator Light	Headlight High-Low Beam (Search)
		Flashing the Headlights (Search)
	Direction Indicator/Hazard Warning Indicator Lights	Turn and Lane-Change Signals (Search)
		Hazard Warning Flasher (Search)
	Electric Parking Brake (EPB) Indication/Indicator Light*1*2	(Search)
	AUTOHOLD Active Indicator Light*1	(Search)
	Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) indicator Light (Some Models)	(Search)
	Cruising & Traffic Support (CTS) indicator Light (Some Models)	(Search)
	TCS/DSC Indication/Indicator Light*1	Traction Control System (TCS) (Search)
		Dynamic Stability Control (DSC) (Search)
		Turns on (Search)
	DSC OFF Indicator Light*1	(Search)
	Select Mode Indicator Light (Some Models)	(Search)
(White)	i-ACTIVSENSE Status Symbol (Warning/Risk Avoidance Support System)	(Search)
(Green)
(Amber)
(Green)	High Beam Control System (HBC) Indicator Light (Some Models)	(Search)
	Adaptive LED Headlights (ALH) Indicator Light (Some Models)	(Search)
(White)	Mazda Radar Cruise Control (MRCC) Standby Indication (Some Models)	(Search)
	Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) Standby Indication (Some Models)	(Search)
	Cruising & Traffic Support (CTS) Standby Indication (Some Models)	(Search)
(Green)	Mazda Radar Cruise Control (MRCC) Set Indication (Some Models)	(Search)
	Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) Set Indication (Some Models)	(Search)
	Cruising & Traffic Support (CTS) Set Indication (Some Models)	(Search)
	Smart Brake Support (SBS) OFF Indicator Light*1 (Some Models)	Smart Brake Support (SBS) (Search)
		Smart Brake Support [Rear] (SBS-R) (Search)
		Smart Brake Support [Rear Crossing] (SBS-RC) (Search)
(White)	Intelligent Speed Assistance (ISA) Standby Indication	(Search)
(Green)	Intelligent Speed Assistance (ISA) Set Indication	(Search)

1. The light turns on when the ignition is switched on for an operation check, and turns off a few seconds later or when the engine is started. If the light does not turn on or remains turned on, have the vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.

2. The light turns on continuously when the parking brake is applied.

The wrench indication/indicator light is displayed/turns on under the following conditions.

• When the preset maintenance period has arrived.

  Refer to the Information section in the MZD Connect Owner's Manual.

• When the engine oil replacement period has arrived.

 

---

• The wrench indication/indicator light may display/turn on earlier than the preset period depending on vehicle usage conditions.

• Whenever the engine oil is replaced, a reset of the vehicle engine control unit is necessary.

  Refer to the Information section in the MZD Connect Owner's Manual.

Close Note

View Note