Contact Authorised Mazda Repairer and Have Vehicle Inspected

If any of the following warning lights or the indicator light turns on/flashes, the system may have a malfunction. Contact an expert repairer, we recommend an Authorised Mazda Repairer to have your vehicle inspected.

Signal

Warning

ABS Warning Light

If the ABS warning light stays on while you're driving, the ABS control unit has detected a system malfunction. If this occurs, your brakes will function normally as if the vehicle had no ABS.

Should this happen, consult an expert repairer, we recommend an Authorised Mazda Repairer as soon as possible.

 


  • When the engine is jump-started to charge the battery, uneven rpm occurs and the ABS warning light may illuminate. If this occurs, it is the result of the weak battery and does not indicate an ABS malfunction.

    Recharge the battery.

  • The brake assist system does not operate while the ABS warning light is illuminated.

Master Warning Indication/Warning Light

With Multi-information Display (Type A/Type B)

(Master warning indication)

Displays when notification of the system malfunctions is required.

Check the message indicated in the display and consult an expert repairer, we recommend an Authorised Mazda Repairer.

(Master warning light)

The master warning light displays when a warning message occurs.

This indicates a malfunction with the vehicle system. Check the message indicated in the display and consult an expert repairer, we recommend an Authorised Mazda Repairer.

For details, refer to the explanations for the warning/indicator lights, in the warning/indicator lights section, which match the symbol in the upper part of the display.

If a message is not indicated in the display, operate the INFO switch to display the “Warning” screen.

Refer to Message Indicated in Multi-information Display (Type A) (Search).

Refer to Message Indicated in Multi-information Display (Type B) (Search).

With Multi-information Display (Type C)

The light illuminates continuously if any one of the following occurs. Consult an expert repairer, we recommend an Authorised Mazda Repairer.

  • There is a malfunction in the battery management system.

  • There is a malfunction in the brake switch.

  • (SKYACTIV-D 2.2)

    • There is a malfunction in the engine's hydraulic control.

    • There is a malfunction in the engine's timing chain.

    • There is a malfunction in the blow-by heater.

    • There is a malfunction in the oil level sensor.

Electric Parking Brake (EPB) Warning Indication/Warning Light

The warning light illuminates when the system has a malfunction. Have your vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.

(Red)

Brake Pedal Operation Demand Warning Light (Some Models)

When only flashing

Flashes if there is the possibility of the vehicle not being held in the stopped position by the AUTOHOLD function, such as on steep slopes. Depress and hold your foot on the brake pedal.

When flashing and beep sound is activated at the same time

The warning light flashes and the beep sound is activated for about 5 seconds if there is a problem with the system. If the warning light flashes and the warning sound is activated, immediately depress the brake pedal and stop using the AUTOHOLD function then contact an expert repairer, we recommend an Authorised Mazda Repairer.

 


Immediately depress the brake pedal if the warning light flashes and the beep sound is activated while using the AUTOHOLD function:

Because the AUTOHOLD function is cancelled forcibly, the vehicle may move unexpectedly and result in an accident.

Electric Parking Brake (EPB) Indication/Indicator Light

This warning has the following functions:

Parking brake warning/Indicator light inspection

The light illuminates when the parking brake is applied with the ignition switched to START or ON. It turns off when the parking brake is released.

When the light is turned on

If the light remains turned on even if the parking brake is released, an expert repairer, we recommend an Authorised Mazda Repairer.

When the light is flashing

The light flashes if the Electric Parking Brake (EPB) has a malfunction. If the light remains flashing even if the Electric Parking Brake (EPB) switch is operated, consult an expert repairer, we recommend an Authorised Mazda Repairer as soon as possible.

Check Engine Light

If this light illuminates while driving, the vehicle may have a problem. It is important to note the driving conditions when the light illuminated and consult an expert repairer, we recommend an Authorised Mazda Repairer.

The check engine light may illuminate in the following cases:

  • The engine's electrical system has a problem.

  • The emission control system has a problem.

  • (Except SKYACTIV-D 2.2)

    The fuel tank level being very low or approaching empty.

If the check engine light remains on, or it flashes continuously , do not drive at high speeds and consult an expert repairer, we recommend an Authorised Mazda Repairer as soon as possible.

 


If the check engine light turns on, do not disconnect the battery leads.

If the battery leads are disconnected and then reconnected, the engine could be damaged and catch on fire.

(Amber)

i-stop Warning Light (Some Models)

When the light is turned on

A problem in the system may be indicated under the following conditions. Have your vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.

  • The light does not turn on when the ignition is switched ON.

  • The light continues to remain on even though the i-stop OFF switch has been pressed while the engine is running.

When the light is flashing

The light continues to flash if the system has a malfunction. Have your vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.

i-ELOOP Warning Indication (Some Models)

The Warning indication turns on if there is any malfunction in the i-ELOOP system. Consult an expert repairer, we recommend an Authorised Mazda Repairer.

Selective Catalytic Reduction (SCR) Warning Indication/Warning Light (Some Models)

If the light turns on

The amount of AdBlue® is low or too much was added. Check the message indicated on the display and consult an expert repairer, we recommend an Authorised Mazda Repairer.

 


If the vehicle continues to be driven while the SCR warning light is turned on, the vehicle's speed may be restricted.

If the light is flashing

There is a problem with the SCR system or the remaining amount of AdBlue® is extremely low. Check the message indicated on the display and have the vehicle inspected by an expert repairer, we recommend an Authorised Mazda Repairer.

 


If the vehicle continues to be driven while the SCR warning light is flashing, the vehicle may stop running. If the SCR warning light flashes, have the vehicle inspected immediately at an expert repairer, we recommend an Authorised Mazda Repairer.

Automatic Transaxle Warning Indication/Warning Light (Some Models)

The indication/light illuminates when the transaxle has a problem.

 


If the automatic transaxle warning indication/light illuminates, the transaxle has an electrical problem. Continuing to drive your Mazda in this condition could cause damage to your transaxle. Consult an expert repairer, we recommend an Authorised Mazda Repairer as soon as possible.

4WD Warning Indication (Some Models)

“4WD system malfunction” is displayed

The indication is displayed under the following conditions. The system may have a malfunction. Have the vehicle checked at an expert repairer, we recommend an Authorised Mazda Repairer.

  • When there is a malfunction in the 4WD system.

  • When there is a large difference between the tyre size of the front and rear wheels.

“4WD system high-load” is displayed

The indication is displayed under the following conditions. Park the vehicle in a safe place and check that the warning indication light turns off, and then drive the vehicle. Contact an expert repairer, we recommend an Authorised Mazda Repairer if the indication is continuously displayed.

  • When the differential oil temperature is excessively high.

  • When there is a large difference between the front and rear wheel rotation, such as when trying to remove the vehicle from mud.

(Turns on)

TCS/DSC Indicator Light

If the light stays on, the TCS, DSC or the brake assist system may have a malfunction and they may not operate correctly. Take your vehicle to an expert repairer, we recommend an Authorised Mazda Repairer.

Air Bag/Seat Belt Pretensioner System Warning Light

A system malfunction is indicated if the warning light constantly flashes, constantly illuminates or does not illuminate at all when the ignition is switched ON. If any of these occur, consult an expert repairer, we recommend an Authorised Mazda Repairer as soon as possible. The system may not operate in an accident.

 


Never tamper with the air bag/pretensioner systems and always have an expert repairer, we recommend an Authorised Mazda Repairer perform all servicing and repairs:

Self-servicing or tampering with the systems is dangerous. An air bag/pretensioner could accidentally activate or become disabled causing serious injury or death.

Active Bonnet Warning Light (Some Models)

The light turns on when the ignition is switched on for an operation check, and turns off a few seconds later.

A problem in the system may be indicated under the following conditions. Have your vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.

  • The light does not turn on when the ignition is switched ON.

  • Remains turned on/flashing.

 


Do not drive the vehicle with the active bonnet warning light turned on or flashing:

Driving the vehicle with the active bonnet warning light turned on or flashing is dangerous as the active bonnet mechanism may not activate normally and function as intended in the event the vehicle were to contact a pedestrian.

(Flashing)

Tyre Pressure Monitoring System Warning Light (Some Models)

If the tyre pressure monitoring system has a malfunction, the tyre pressure warning light flashes. Have your vehicle checked by an expert repairer, we recommend an Authorised Mazda Repairer as soon as possible.

 


If the tyre pressure monitoring system warning light illuminates or flashes, or the tyre pressure warning beep sound is heard, decrease vehicle speed immediately and avoid sudden manoeuvring and braking:

If the tyre pressure monitoring system warning light illuminates or flashes, or the tyre pressure warning beep sound is heard, it is dangerous to drive the vehicle at high speeds, or perform sudden manoeuvring or braking. Vehicle drivability could worsen and result in an accident.

To determine if you have a slow leak or a flat, pull over to a safe position where you can check the visual condition of the tyre and determine if you have enough air to proceed to a place where air may be added and the system monitored again by an expert repairer, we recommend an Authorised Mazda Repairer or a tyre repair station.

Do not ignore the TPMS Warning Light:

Ignoring the TPMS warning light is dangerous, even if you know why it is illuminated. Have the problem taken care of as soon as possible before it develops into a more serious situation that could lead to tyre failure and a dangerous accident.

(Amber)

KEY Warning Indication (Some Models)

“Keyless System malfunction” is displayed

This message is displayed if the advanced keyless entry & push button start system has a problem.

Contact an expert repairer, we recommend an Authorised Mazda Repairer.

 


If the message is indicated, or the push button start indicator light (amber) flashes, the engine may not start. If the engine cannot be started, try starting it using the emergency operation for starting the engine, and have the vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer as soon as possible.

Refer to Emergency Operation for Starting the Engine (Search).

“Set Power to OFF” is displayed

This message is displayed when the driver's door is opened without switching the ignition off.

“Key not found” is displayed

This message is displayed when any of the following operations is performed with the key out of the operational range or placed in areas inside the cabin where it is difficult for the key to be detected.

  • The push button start is pressed with the ignition switched off

  • The ignition is switched on

  • All doors are closed without switching the ignition off

(Red)

(Turns on)

KEY Warning Light (Some Models)

If any malfunction occurs in the keyless entry system, it illuminates continuously.

 


If the key warning indicator light illuminates or the push button start indicator light (amber) flashes, the engine may not start. If the engine cannot be started, try starting it using the emergency operation for starting the engine, and have the vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer as soon as possible.

Refer to Emergency Operation for Starting the Engine (Search).

Security Indicator Light

If the engine does not start with the correct key, and the security indicator light remains illuminated or flashing, try the following:

Make sure the key is within the operational range for signal transmission. Switch the ignition off, and then restart the engine. If the engine does not start after 3 or more tries, contact an expert repairer, we recommend an Authorised Mazda Repairer.

(Amber)

High Beam Control System (HBC) Warning Indication/Warning Light (Some Models)

The light remains turned on if there is a problem with the system. Have your vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.

 


If the Forward Sensing Camera (FSC) field of view is impaired during bad weather conditions (such as rain, fog, and snow) and when the windscreen is dirty, the warning indication/warning light for the High Beam Control System (HBC) may display/turn on. However, this does not indicate a problem.

(Amber)

Adaptive LED Headlights (ALH) Warning Indication/Warning Light (Some Models)

The light remains turned on if there is a problem with the system. Have your vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.

 


If the Forward Sensing Camera (FSC) field of view is impaired during bad weather conditions (such as rain, fog, and snow) and when the windscreen is dirty, the warning indication/warning light for the Adaptive LED Headlights (ALH) may display/turn on. However, this does not indicate a problem.

Blind Spot Monitoring (BSM) Warning Indication (Some Models)

The Warning indication turns on if there is any malfunction in the Blind Spot Monitoring (BSM). Have your vehicle inspected by an expert repairer, we recommend an Authorised Mazda Repairer.

 


If the vehicle is driven on a road with less traffic and few vehicles that the radar sensors can detect, the system may pause. However, it does not indicate a malfunction.

Blind Spot Monitoring (BSM) OFF Indicator Light (Some Models)

A problem in the system may be indicated under the following conditions.

Have your vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.

  • The light does not turn on when the ignition is switched ON.

  • The light remains on even when the Blind Spot Monitoring (BSM) system can be operated.

  • The light turns on while driving the vehicle.

 


If the vehicle is driven on a road with less traffic and few vehicles that the radar sensors can detect, the system may pause (The Blind Spot Monitoring (BSM) OFF indicator light in the instrument cluster illuminates). However, it does not indicate a malfunction.

(Amber)

Driver Attention Alert (DAA) Warning Indication (Some Models)

The message is displayed when the system has a malfunction. Have your vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.

(Amber)

Mazda Radar Cruise Control (MRCC) Warning Indication (Some Models)

The message is displayed when the system has a malfunction. Have your vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.

(Amber)

Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) Warning Indication (Some Models)

The message is displayed when the system has a malfunction. Have your vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.

(Turns on)

Lane Departure Warning System (LDWS) Warning Indication/Warning Light (Some Models)

  • The warning indication/warning light illuminates if there is a problem with the system. Have your vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.

  • The system does not operate when the warning indication/warning light illuminates.

 


  • Always use tyres for all wheels that are of the specified size, and the same manufacture, brand, and tread pattern. In addition, do not use tyres with significantly different wear patterns on the same vehicle. If such improper tyres are used, the Lane Departure Warning System (LDWS) may not operate normally.

  • When an emergency spare tyre is used, the system may not operate normally.

Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) Warning Indication (Some Models)

The message is displayed when the system has a malfunction. Have your vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.

The system does not operate when the warning message is displayed.

 


  • Always use tyres for all wheels that are of the specified size, and the same manufacture, brand, and tread pattern. In addition, do not use tyres with significantly different wear patterns on the same vehicle. If such improper tyres are used, the system may not operate normally.

  • When an emergency spare tyre is used, the system may not operate normally.

LED Headlight Warning Light

This light illuminates if there is a malfunction in the LED headlight. Have your vehicle inspected by an expert repairer, we recommend an Authorised Mazda Repairer.

Page top