Instrument Cluster and Display

The speedometer indicates the speed of the vehicle.

The tachometer shows engine speed in thousands of revolutions per minute (rpm).

 

---

Do not run the engine with the tachometer needle in the RED ZONE.

This may cause severe engine damage.

 

Close Caution

View Caution

 

---

When the tachometer needle enters the STRIPED ZONE, this indicates to the driver that the gears should be shifted before entering the RED ZONE.

Close Note

View Note

The multi-information display indicates the following information.

• Speedometer

• Odometer

• Trip meter

• Outside temperature

• Distance-to-empty

• Average fuel economy

• Current fuel economy

• Maintenance Monitor

• Blind Spot Monitoring (BSM) Display

• Traffic Sign Recognition System (TSR) Display

• Distance Recognition Support System (DRSS) Display

• Mazda Radar Cruise Control (MRCC) Display

• Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) Display

• Intelligent Speed Assistance (ISA) Display

• Vehicle Speed Alarm

• Door-Ajar/Boot lid-Ajar/Liftgate-Ajar Warning Indication

• Message Display

The screen content changes each time the INFO switch is pressed.

The screen content changes each time the selector knob is pressed and held.

The odometer is constantly displayed on the screen when the ignition is switched ON, and the TRIP A or TRIP B screen can be displayed by operating the INFO switch.

Odometer

The odometer records the total distance the vehicle has been driven.

Trip meter

The driving distance for a specified interval is indicated. Two types (TRIP A, TRIP B) of interval distance and the average fuel economy for each can be measured.

For instance, trip meter A can record the distance from the point of origin, and trip meter B can record the distance from where the fuel tank is filled.

When trip meter A is selected, TRIP A will be displayed. When trip meter B is selected, TRIP B will be displayed.

The trip meter and average fuel economy can be reset by pressing the INFO switch for 1.5 seconds or more while in each mode.

 

---

• Only the trip meters record tenths of kilometres (miles).

• The trip record will be erased when:

  • The power supply is interrupted (blown fuse or the battery is disconnected).

  • The vehicle is driven over 9999.9 km (mile).

Close Note

View Note

Displays the engine coolant temperature. The blue range of the gauge indicates that the engine coolant temperature is low, and the red range of the gauge indicates that the engine coolant temperature is high and overheating.

 

---

If the engine coolant temperature gauge needle is in the red range, there is the possibility of overheating. Drive slowly to reduce engine load until you can find a safe place to stop the vehicle and wait for the engine to cool down.

Refer to Overheating (Search).

Close Caution

View Caution

 

---

• During normal driving, the engine coolant temperature stabilizes at 100 °C (210 °F) or less, and the gauge indicates a range lower than 100 °C (210 °F).

Close Note

View Note

The fuel gauge shows approximately how much fuel is remaining in the tank when the ignition is switched ON. We recommend keeping the tank over 1/4 full.

If the low fuel warning light illuminates or the fuel level is very low, refuel as soon as possible.

Refer to Taking Action (Search).

 

---

• After refuelling, it may require some time for the indicator to stabilize. In addition, the indicator may deviate while driving on a slope or curve since the fuel moves in the tank.

• The direction of the arrow () indicates that the fuel-filler flap is on the left side of the vehicle.

Close Note

View Note

(SKYACTIV-D 2.2)

If inconsistency in engine performance or stalling occurs due to low fuel level conditions, refuel the vehicle as soon as possible and add at least 10 L (2.7 US gal, 2.2 Imp gal) of fuel.

When the lights are turned on with the ignition switched ON, the brightness of the instrument panel illumination is dimmed. However, when the light sensor detects that the surrounding area is bright such as when the lights are turned on in the daytime, the instrument panel illumination does not dim.

 

---

• When the ignition is switched ON in the early evening or at dusk, the instrument panel illumination is dimmed for several seconds until the light sensor detects the brightness of the surrounding area, however, the dimming may cancel after the brightness is detected.

• When the lights are turned on, the lights-on indicator light in the instrument cluster turns on.

  Refer to Headlights (Search).

Close Note

View Note

The brightness of the instrument cluster and instrument panel illuminations can be adjusted by rotating the knob.

• The brightness decreases by rotating the knob to the left. A beep sound will be heard when the knob has been rotated to the maximum dim position.

• The brightness increases by rotating the knob to the right.

Function for cancelling illumination dimmer

The illumination dimmer can be cancelled by rotating the instrument panel illumination knob to the right until a beep sound is heard while the instrument cluster is dimmed with the ignition switched ON. If the instrument cluster's visibility is reduced due to glare from surrounding brightness, cancel the illumination dimmer.

 

---

• When the illumination dimmer is cancelled, the instrument cluster cannot be dimmed even if the lights are turned on.

• When the illumination dimmer is cancelled, the screen in the centre display switches to constant display of the daytime screen.

Close Note

View Note

When the ignition is switched ON, the outside temperature is displayed.

 

---

• Under the following conditions, the outside temperature display may differ from the actual outside temperature depending on the surroundings and vehicle conditions:

  • Significantly cold or hot temperatures.

  • Sudden changes in outside temperature.

  • The vehicle is parked.

  • The vehicle is driven at low speeds.

Close Note

View Note

Changing the Temperature Unit of the Outside Temperature Display

The outside temperature unit can be switched between Celsius and Fahrenheit.

Settings can be changed by operating the centre display screen.

Refer to Other Equipment/Functions (Search).

 

---

When the temperature unit indicated in the outside temperature display is changed, the temperature unit indicated in the engine coolant gauge display changes in conjunction with it.

Close Note

View Note

This displays the approximate distance you can travel on the remaining fuel based on the fuel economy.

The distance-to-empty will be calculated and displayed every second.

 

---

• Even though the distance-to-empty display may indicate a sufficient amount of remaining driving distance before refuelling is required, refuel as soon as possible if the fuel level is very low or the low fuel warning light illuminates.

• The display will not change unless you add more than approximately 9 L (2.3 US gal, 1.9 Imp gal) of fuel.

• The distance-to-empty is the approximate remaining distance the vehicle can be driven until all the graduation marks in the fuel gauge indicating the remaining fuel supply disappear.

• If there is no past fuel economy information such as after first purchasing your vehicle or the information is deleted when the battery leads are disconnected, the actual distance-to empty/range may differ from the amount indicated.

Close Note

View Note

The average fuel economy is calculated every minute from the total travelled distance on the trip meter and the total fuel consumption, and the average fuel economy for either TRIP A or TRIP B is displayed.

The average fuel economy and trip meters can be reset by pressing the INFO switch for 1.5 seconds or more while in each mode. After the data is cleared, the fuel consumption is recalculated and the - - - km/L (- - - mpg) for the 1 minute prior to it being displayed is indicated.

This displays the current fuel economy by calculating the amount of fuel consumption and the distance travelled.

The average fuel economy for TRIP A is indicated by a blue arrow.

 

---

Indicates the 0 position when the vehicle speed is about 5 km/h (3 mph) or slower.

Close Note

View Note

In this mode, the current setting for the vehicle speed alarm is displayed. You can change the vehicle speed setting at which the warning is triggered.

 

---

The vehicle speed alarm display is activated at the same time the beep sound is heard.

Close Note

View Note

The vehicle speed alarm can be set using the centre display.

 

---

Always set the vehicle speed according to the laws and regulations of the country/city in which the vehicle is driven. In addition, always verify the speed of the vehicle using the speedometer.

Close Note

View Note

The following maintenance period notifications can be displayed by turning the Maintenance Monitor on.

• Scheduled Maintenance

• Tyre Rotation

• Oil Change

When the remaining days to the maintenance period is 15 days or less, or the remaining distance is 1,000 km (600 miles) or shorter, a message is indicated when the ignition is switched ON.

For the setting method and indications for the maintenance monitor, refer to the Maintenance Monitor.

Refer to Maintenance Monitor (Search).

Displays the system status.

Refer to Blind Spot Monitoring (BSM) (Search).

Displays the traffic sign.

Refer to Traffic Sign Display Indication (Search).

Displays the system status.

Refer to Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) (Search).

Displays the currently set system status.

Refer to Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) (Search).

Displays the distance between your vehicle and the vehicle ahead.

Refer to Distance Recognition Support System (DRSS) (Search).

The setting status of the Intelligent Speed Assistance (ISA) is displayed.

Refer to Intelligent Speed Assistance (ISA) (Search).

A message such as the system operation status, a malfunction, or an abnormality is indicated.

Warning/indicator light in instrument cluster turns on/flashes or symbol is indicated on display at same time as message

Check the information regarding the warning/indicator light or indicated symbol.

Refer to If a Warning Indication/Warning Lights (Search).

Refer to If a Indication/Indicator Lights (Search).

Message only is indicated on display

Follow the instructions indicated on the display. For the display content, refer to the next page.

Refer to If a Message Indicated on Multi-information Display (Search).

Instrument Cluster varies depending on model and specifications.

These lights turn on or flash to notify the user of the system operation status or a system malfunction.

Signal	Warning	Page
	Brake System Warning Light*1	(Search)
	ABS Warning Light*1	Electronic Brake Force Distribution System Warning (Search)
		ABS warning (Search)
	Charging System Warning Indication/Warning Light*1	(Search)
	Engine Oil Warning Light*1	(Search)
	High Engine Coolant Temperature Warning Indication	(Search)
	Power Steering Malfunction Indication	(Search)
	Master Warning Indication	(Search)
	Electric Parking Brake (EPB) Warning Indication/Warning Light*1	(Search)
	Check Engine Light*1	(Search)
(Amber)	i-stop Warning Light*1	(Search)
	i-ELOOP Warning Indication (Some Models)	(Search)
	Automatic Transaxle Warning Indication	(Search)
	Air Bag/Seat Belt Pretensioner System Warning Light*1	(Search)
	Active Bonnet Warning Light*1	(Search)
	Tyre Pressure Monitoring System Warning Light*1	Flashing (Search)
		Turns on (Search)
(Amber/White)	KEY Warning Indication	Amber (Search)
		White (Search)
(Amber)	High Beam Control System (HBC) Warning Indication/Warning Light*1 (Some Models)	(Search)
	Adaptive LED Headlights (ALH) Warning Indication/Warning Light*1 (Some Models)	(Search)
	Blind Spot Monitoring (BSM) Warning Indication	(Search)
(Amber)	Driver Attention Alert (DAA) Warning Indication (Some Models)	(Search)
(Amber)	Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) Warning Indication	(Search)
	Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) Warning Indication	(Search)
	LED Headlight Warning Light*1	(Search)
	Smart Brake Support/Smart City Brake Support (SBS/SCBS) Warning Indication	(Search)
	Low Fuel Warning Indication/Warning Light	(Search)
	Engine Oil Level Warning Light*1	(Search)
	Seat Belt Warning Light (Front seat)	(Search)
(Red)	Seat Belt Warning Light (Rear seat)	(Search)
	Door-Ajar Warning Indication	(Search)
	Boot lid-Ajar Warning Indication (Some Models)	(Search)
	Liftgate-Ajar Warning Indication (Some Models)	(Search)
	Door-Ajar Warning Light	(Search)

1. The light turns on when the ignition is switched on for an operation check, and turns off a few seconds later or when the engine is started. If the light does not turn on or remains turned on, have the vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.

These lights turn on or flash to notify the user of the system operation status or a system malfunction.

Signal	Indicator	Page
(Green)	Seat Belt Indicator Light (Rear seat)	(Search)
	Front Passenger Air Bag Deactivation Indicator Light*1	(Search)
(Green)	i-stop Indicator Light	(Search)
	Security Indicator Light*1	(Search)
	Vehicle Speed Alarm Indication	(Search)
	Wrench Indication	(Search)
	Glow Indicator Light*1 (Some Models)	(Search)
	Diesel Particulate Filter Indication (Some Models)	(Search)
	Shift Position Indication	(Search)
	Lights-On Indication/Indicator Light	(Search)
	Headlight High-Beam Indicator Light	Headlight High-Low Beam (Search)
		Flashing the Headlights (Search)
	Direction Indicator/Hazard Warning Indicator Lights	Turn and Lane-Change Signals (Search)
		Hazard Warning Flasher (Search)
	Electric Parking Brake (EPB) Indication/Indicator Light*1*2	(Search)
	AUTOHOLD Active Indicator Light*1	(Search)
	Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) indicator Light	(Search)
	TCS/DSC Indicator Light*1	Traction Control System (TCS) (Search)
		Dynamic Stability Control (DSC) (Search)
		Turns on (Search)
	DSC OFF Indicator Light*1	(Search)
	Select Mode Indication (Some Models)	(Search)
(Green)	High Beam Control System (HBC) Indicator Light (Some Models)	(Search)
	Adaptive LED Headlights (ALH) Indicator Light (Some Models)	(Search)
	Blind Spot Monitoring (BSM) OFF Indicator Light*1	Except malfunction (Search)
		Malfunction (Search)
(White)	Driver Attention Alert (DAA) Indication (Some Models)	(Search)
(White)	Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) Main Indication	(Search)
(Green)	Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) Set Indication	(Search)
	Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) Indication	(Search)
	Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) OFF Indicator Light*1	(Search)
	Smart City Brake Support (SCBS) Indication	Advanced Smart City Brake Support (Advanced SCBS) (Search)
		Smart City Brake Support [Reverse] (SCBS R) (Search)
	Smart Brake Support/Smart City Brake Support (SBS/SCBS) OFF Indicator Light*1	Advanced Smart City Brake Support (Advanced SCBS) (Search)
		Smart City Brake Support [Reverse] (SCBS R) (Search)
		Smart Brake Support (SBS) System (Search)
(White)	Intelligent Speed Assistance (ISA) Main Indication	(Search)
(Green)	Intelligent Speed Assistance (ISA) Set Indication	(Search)

1. The light turns on when the ignition is switched on for an operation check, and turns off a few seconds later or when the engine is started. If the light does not turn on or remains turned on, have the vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.

2. The light turns on continuously when the parking brake is applied.

The wrench indication is displayed under the following conditions.

• When the preset maintenance period has arrived.

  Refer to Maintenance Monitor (Search).

• When the engine oil replacement period has arrived.

• (SKYACTIV-D 2.2)

  • When the engine oil is deteriorated or exceeds the specified amount.

  • When fuel filter (sedimentor) draining is required. Consult an expert repairer, we recommend an Authorised Mazda Repairer.

 

---

• The wrench indication may display earlier than the preset period depending on vehicle usage conditions.

• Whenever the engine oil is replaced, a reset of the vehicle engine control unit is necessary.

  Your Authorised Mazda Repairer will be able to reset the engine control unit or see (Search) for the Vehicle engine control unit reset procedure.

Close Note

View Note

When the ignition is switched ON, the glow indicator light turns on. The glow indicator light turns off when preheating is finished.

A problem in the system might be indicated under the following conditions. Have your vehicle inspected by an expert repairer, we recommend an Authorised Mazda Repairer.

• The glow indicator light does not turn on when the ignition is switched ON or it remains on.

• The glow indicator light is flashing.

 

---

If the vehicle is left with the ignition switched ON without starting the engine and a long period of time has elapsed since preheating finished, the preheating may be performed again and the glow indicator light may turn on.

Close Note

View Note