Owner Maintenance

1. With the vehicle parked, pull the release handle to unlock the bonnet.

    

   

2. Insert your hand into the bonnet opening, slide the latch lever to the right, and lift up the bonnet.

    

   

    

   ---

   The lever is located a little to the left of centre when facing the vehicle.

   Close Note

   View Note

3. Grasp the support rod in the padded area and secure it in the support rod hole indicated by the arrow to hold the bonnet open.

    

   

1. Check under the bonnet area to make certain all filler caps are in place and all loose items (e.g. tools, oil containers, etc.) have been removed.

2. Lift the bonnet, grasp the padded area on the support rod, and secure the support rod in the clip. Verify that the support rod is secured in the clip before closing the bonnet.

    

   

3. Lower the bonnet slowly to a height of about 20 cm (7.9 in) above its closed position and then let it drop.

In order to keep the maintenance interval (Search) and to protect the engine from damage caused by poor lubrication, it is vitally important to make use of engine oil with the correct specification. Do not use oils which do not meet the following specifications or requirements. Use of unsuitable oil may lead to engine damage which is not covered by the Mazda Warranty.

 

Engine oil viscosity, or thickness, has an effect on fuel economy and cold-weather operation (starting and oil flow).

Low-viscosity engine oils can provide improved fuel economy and cold-weather performance.

 

(SKYACTIV-G 2.5)

Mazda recommends using Mazda Premium Motor Oil (for Australia) or Mazda Motor Oil (for New Zealand) which has been specifically designed and tested to meet the stringent Mazda Engineering Standards (MES) for your Mazda. To ensure engine longevity is not compromised particularly under the harsh climatic conditions existing in Australia and New Zealand, we only recommend using genuine Mazda engine oil which is available throughout the Mazda Dealer network.

 

If Mazda Premium Motor Oil (for Australia) or Mazda Motor Oil (for New Zealand) is not selected for use, always use an engine oil meeting the specifications:

 

Use ILSAC GF-III/GF-IV/GF-V, or API service SL or higher.

 

(SKYACTIV-G 2.5T)

Use ILSAC GF-IV/GF-V, or API service SM or higher.

When choosing an oil, consider the temperature range your vehicle will operate in before the next oil change.

Then select the recommended viscosity from the chart.

New Zealand

Mazda recommends using Mazda Motor Oil which has been specifically designed and tested to meet the stringent Mazda Engineering Standards (MES) for your Mazda. To ensure engine longevity is not compromised particularly under the harsh climatic conditions existing in New Zealand, we only recommend using genuine Mazda engine oil which is available throughout the Mazda Repairer network.

 

If Mazda Motor Oil is not selected for use, always use an engine oil meeting the specifications.

 

(SKYACTIV-D 2.2)

Mazda recommends using Mazda Diesel Engine Oil which has been specifically designed and tested to meet the stringent Mazda Engineering Standards (MES) for your Mazda. To ensure engine longevity is not compromised particularly under the harsh climatic conditions existing in Australia and New Zealand, we only recommend using genuine Mazda Diesel Engine Oil which is available throughout the Mazda Dealer network.

 

If Mazda Diesel Engine Oil is not selected for use, always use an engine oil meeting the specifications:

 

Use ACEA C3.

 

When choosing an oil, consider the temperature range your vehicle will operate in before the next oil change.

Then select the recommended viscosity from the chart.

After replacing the engine oil, have a repair shop such as an Authorised Mazda Repairer perform the initialization (engine oil data resetting) of the recorded value. If the value recorded by the computer is not initialized, the wrench indicator light may not turn off or it may turn on earlier than normal.

1. Be sure the vehicle is on a level surface.

2. Warm up the engine to normal operating temperature.

3. Turn it off and wait at least 5 minutes for the oil to return to the sump.

4. Pull out the dipstick, wipe it clean, and reinsert it fully.

   SKYACTIV-G 2.5 and SKYACTIV-G 2.5T

    

   

   SKYACTIV-D 2.2

    

   

    

   ---

   (SKYACTIV-D 2.2)

   When inspecting the engine oil level, pull out the dipstick straight without twisting. In addition, when inserting the dipstick, always insert it without twisting so that the “X” mark faces the front of the vehicle.

   Close Note

   View Note

5. Pull it out again and examine the level.

   The level is normal if it is between the MIN and MAX marks.

   If it is near or below MIN, add enough oil to bring the level to MAX.

    

   ---

   Do not overfill the engine oil. This may cause engine damage.

   Close Caution

   View Caution

6. Make sure the O-ring on the dipstick is positioned properly before reinserting the dipstick.

7. Reinsert the dipstick fully.

Inspect the antifreeze protection and coolant level in the coolant reservoir at least once a year―at the beginning of the winter season―and before travelling where temperatures may drop below freezing.

 

Inspect the condition and connections of all cooling system and heater hoses.

Replace any that are swollen or deteriorated.

 

The coolant should be at full in the radiator and between the F and L marks on the coolant reservoir when the engine is cool.

SKYACTIV-G 2.5

 

SKYACTIV-G 2.5T

 

SKYACTIV-D 2.2

 

If it is at or near L, add enough coolant to the coolant reservoir to provide freezing and corrosion protection and to bring the level to F.

Securely tighten the coolant reservoir tank cap after adding coolant.

If the coolant reservoir is empty or new coolant is required frequently, consult an expert repairer, we recommend an Authorised Mazda Repairer.

Inspect the fluid level in the reservoir regularly. It should be kept between the MAX and MIN lines.

The level normally drops with accumulated distance, a condition associated with wear of brake linings. If it is excessively low, have the brake system inspected by an expert repairer, we recommend an Authorised Mazda Repairer.

Inspect fluid level in the washer fluid reservoir; add fluid if necessary.

 

 

Use plain water if washer fluid is unavailable.

But use only washer fluid in cold weather to prevent it from freezing.

When the wipers no longer clean well, the blades are probably worn or cracked.

Replace them.

Replace the wiper blades using the following procedure.

1. Raise the wiper arm.

    

   ---

   To prevent damage to the windscreen let the wiper arm down easily, do not let it slap down on the windscreen.

   Close Caution

   View Caution

2. Slide the blade component in the direction of the arrow while pressing the wiper arm tab to remove the blade component from the wiper arm.

    

   

3. Pull the blade rubber in the direction of the arrow and slide it to a position where the blade holder groove can be checked.

    

   

4. Pull the end of the blade rubber from the blade holder groove in the direction of the arrow and remove the blade rubber from the blade holder.

    

   

5. Insert the end of the new blade rubber into the groove of the blade holder until it contacts the end of the blade holder.

    

   

6. After pulling the blade rubber in the direction of the arrow and sliding the blade rubber to a position to check the blade holder groove, slide the blade rubber end in the opposite direction.

    

   

7. Make sure that the blade rubber is correctly installed to the blade holder.

8. Align the wiper arm tabs with the blade component grooves.

    

   

9. Align the blade component projection with the wiper arm notch.

    

   

10. Slide the blade component and install it to the wiper arm.

     

    

11. Slowly lower the wiper arm onto the windscreen.

When the wiper no longer cleans well, the blade is probably worn or cracked.

Replace it.

1. Raise the wiper arm and rotate the wiper blade to the right until it unlocks, then remove the blade.

    

   

    

   ---

   To prevent damage to the rear window, do not let the wiper arm fall on it.

   Close Caution

   View Caution

2. Pull down the blade rubber and slide it out of the blade holder.

    

   

3. Remove the metal stiffeners from the blade rubber and install them in the new blade.

    

   

    

   ---

   Do not bend or discard the stiffeners. You need to use them again.

   Close Caution

   View Caution

4. Carefully insert the new blade rubber.

   Then install the blade assembly in the reverse order of removal.

    

   

To get the best service from a battery:

• Keep it securely mounted.

• Keep the top clean and dry.

• Keep terminals and connections clean, tight, and coated with petroleum jelly or terminal grease.

• Rinse off spilled electrolyte immediately with a solution of water and baking soda.

• If the vehicle will not be used for an extended time, disconnect the battery leads and charge the battery every 6 weeks.

A low level of electrolyte fluid will cause the battery to discharge quickly.

 

Inspect the electrolyte level at least once a week. If it is low, remove the caps and add enough distilled water to bring the level between the upper and lower level (illustration).

 

Do not overfill.

Examine the specific gravity of the electrolyte with a hydrometer, especially during cold weather. If it is low, recharge the battery.

• If the battery quickly discharges because, for example, the lights were left on too long with the engine off, slow-charge it as required by battery size and charger capacity.

• If the battery gradually discharges because of high electric load while the vehicle is being used, recharge it as required by battery size and charger capacity.

Contact an Authorised Mazda Repairer for a battery replacement purchase.

Inspect all tyre pressures monthly (including the spare) when the tyres are cold. Maintain recommended pressures for the best ride, handling, and minimum tyre wear.

Refer to the specification charts (Search).

During rotation, inspect them for correct balance.

 

Also, inspect them for uneven wear and damage. Abnormal wear is usually caused by one or a combination of the following:

 

• Incorrect tyre pressure

• Improper wheel alignment

• Out-of-balance wheel

• Severe braking

 

After rotation, inflate all tyre pressures to specification (Search) and inspect the wheel nuts for tightness.

If a tyre wears evenly, a wear indicator will appear as a solid band across the tread.

Replace the tyre when this happens.

You should replace the tyre before the band crosses the entire tread.

Inspect the temporary spare tyre at least monthly to make sure it is properly inflated and stored.

The temporary spare tyre is easier to handle because of its construction which is lighter and smaller than a conventional tyre. This tyre should be used only for an emergency and only for a short distance.

 

Use the temporary spare tyre only until the conventional tyre is repaired, which should be as soon as possible.

 

Refer to Tyre (Search).

 

Proper tyre balancing provides the best riding comfort and helps reduce tread wear. Out-of-balance tyres can cause vibration and uneven wear, such as cupping and flat spots.

The exterior lights have either LEDs or normal bulbs.

Only the bulb for a running light/position lights can be replaced.

LED type

• Headlights

• Running lights/Position lights (Some Models)

• Front direction indicator lights

• Side direction indicator lights

• High-mount brake light

• Rear direction indicator lights (Saloon)

• Brake lights/Tail lights

• Tail lights (Some Models)

• Reverse lights (Saloon)

• Number plate lights

The LED bulb cannot be replaced as a single unit because it is an integrated unit.

The LED bulb has to be replaced with the unit. We recommend an Authorised Mazda Repairer when the replacement is necessary.

Bulb type

Running lights/Position lights (Some Models)

1. Make sure the ignition is switched off, and the headlight switch is off.

2. If you are changing the right bulb, start the engine, turn the steering wheel all the way to the left, and turn off engine. If you are changing the left bulb, turn the steering wheel to the right.

3. Pull the centre of each plastic retainer and remove the retainers.

    

   

4. Turn the screw anticlockwise and remove it, and then partially peel back the mudguard.

    

   

5. Turn the socket and bulb assembly anticlockwise and remove it.

6. Disconnect the bulb from the socket.

    

   

7. Install the new bulb in the reverse order of the removal procedure.

Rear direction indicator lights (Wagon)

1. Make sure the ignition is switched off, and the headlight switch is off.

2. Remove the cover.

   

3. Turn the socket and bulb assembly anticlockwise and remove it.

4. Disconnect the bulb from the socket.

   

5. Install the new bulb in the reverse order of the removal procedure.

Tail lights (Liftgate side), Reverse light (Wagon)

1. Make sure the ignition is switched off, and the headlight switch is off.

2. Remove the cover with a cloth-wrapped flathead screwdriver to the cover.

   

3. Turn the socket and bulb assembly anticlockwise and remove it.

4. Disconnect the bulb from the socket.

   Tail lights (Liftgate side)

   

   Reverse light (Wagon)

   

5. Install the new bulb in the reverse order of the removal procedure.

Overhead lights/Front map lights (LED type), Rear map lights (LED type), Vanity mirror lights (LED type), Courtesy lights, Ambient lights (Some Models)

The LED bulb cannot be replaced as a single unit because it is an integrated unit.

The LED bulb has to be replaced with the unit. We recommend an Authorised Mazda Repairer if the replacement is necessary.

Overhead lights/Front map lights (Bulb type), Rear map lights (Bulb type), Vanity mirror lights (Bulb type)

1. Wrap a small flathead screwdriver with a soft cloth to prevent damage to the lens, and then remove the lens by carefully prying on the edge of the lens with the flathead screwdriver.

2. Disconnect the bulb by pulling it out.

   Overhead lights/Front map lights

    

   

    

   

   Rear map lights

    

   

    

   

   Vanity mirror lights

   

3. Install the new bulb in the reverse order of the removal procedure.

Boot light (Saloon)

(LED type)

The LED bulb cannot be replaced as a single unit because it is an integrated unit.

The LED bulb has to be replaced with the unit. We recommend an Authorised Mazda Repairer if the replacement is necessary.

(Bulb type)

1. Press both sides of the lens cap to remove it.

2. Disconnect the bulb by pulling it out.

    

   

3. Install the new bulb in the reverse order of the removal procedure.

Luggage compartment light (Wagon)

(LED type)

The LED bulb cannot be replaced as a single unit because it is an integrated unit.

The LED bulb has to be replaced with the unit. We recommend an Authorised Mazda Repairer if the replacement is necessary.

(Bulb type)

1. Wrap a small flathead screwdriver with a soft cloth to prevent damage to the lens and remove the lens unit by carefully prying on the edge of the lens unit with the flathead screwdriver.

    

   

2. Disconnect the electrical connector from the bulb by pressing the tab on the connector with your finger and pulling the connector.

    

   

    

   ---

   When replacing the bulb always disconnect the connector first. Otherwise, electric and electronic devices could be shorted.

   Close Caution

   View Caution

3. Insert the flathead screwdriver into the gap between the lens and the lens unit, and then slide the screwdriver to detach the lens.

    

   

4. Disconnect the bulb by pulling it out.

    

   

5. Install the new bulb in the reverse order of the removal procedure.

Replacing the fuses on the vehicle's left side

If the electrical system does not work, first inspect the fuses on the vehicle's left side.

 

1. Make sure the ignition is switched off, and other switches are off.

2. Open the fuse panel cover.

   

3. Pull the fuse straight out with the fuse puller provided on the fuse block located in the engine compartment.

   

4. Inspect the fuse and replace it if it is blown.

   

5. Insert a new fuse of the same amperage rating, and make sure it fits tightly. If it does not fit tightly, have an expert install it. We recommend an Authorised Mazda Repairer.

   If you have no spare fuses, borrow one of the same rating from a circuit not essential to vehicle operation, such as the AUDIO or OUTLET circuit.

    

   ---

   Always replace a fuse with a genuine Mazda fuse or equivalent of the same rating. Otherwise you may damage the electric system.

   Close Caution

   View Caution

6. Reinstall the cover and make sure that it is securely installed.

Replacing the fuses under the bonnet

If the headlights or other electrical components do not work and the fuses in the cabin are normal, inspect the fuse block under the bonnet.

If a fuse is blown, it must be replaced. Follow these steps:

 

1. Make sure the ignition is switched off, and other switches are off.

2. Remove the fuse block cover.

   

3. If any fuse but the MAIN fuse is blown, replace it with a new one of the same amperage rating.

   

    

   ---

   Do not replace the main fuse by yourself. Have an Authorised Mazda Repairer perform the replacement:

   Replacing the fuse by yourself is dangerous because the MAIN fuse is a high current fuse. Incorrect replacement could cause an electrical shock or a short circuit resulting in a fire.

   Close Warning

   View Warning

4. Reinstall the cover and make sure that it is securely installed.

Fuse block (Engine compartment)

Fuse block (Left side)