Specifications

Battery

1. Q-85 or S-95 is designed for i-stop system (FOR STOP & START)/i-ELOOP system. Only Q-85 or S-95 should be used to ensure correct operation of i-stop system (FOR STOP & START)/i-ELOOP system. Consult an expert repairer, we recommend an Authorised Mazda Repairer for details.

2. Not for i-stop system/i-ELOOP system.

Spark-plug

1. The spark plugs provide the SKYACTIV-G its optimum performance. Consult an expert repairer, we recommend an Authorised Mazda Repairer for details.

 

---

When cleaning the iridium plugs, do not use a wire brush. The fine particulate coating on the iridium alloy and platinum tips could be damaged.

Close Caution

View Caution

1. Refer to Recommended Oil (Search)

2. Mazda Original Oils are specially designed/tested for the respective engine. For optimum performance we recommend to use Mazda Original Oils at all times.

3. If you are unable to find a Mazda Original Oil, alternative oils meeting the listed specification may also be used.

4. Use API SM/SN in Kazakhstan.

Do not use oils which do not meet the above specification or requirements. Use of unsuitable oil may lead to engine damage which is not covered by the Mazda Warranty.

1. Mazda Long Life Gear Oil G7 is superior oil for low fuel cost and optimum shift-feel. Using Mazda Long Life Gear Oil G7 is recommended.

   If Mazda Long Life Gear Oil G7 cannot be obtained, use standard oil (API Service GL-4 (SAE 75W-80)).

1. Use Mazda genuine deposit cleaner. Using non-genuine deposit cleaner would cause internal failure of the fuel system. Refer to (Search), (Search) for the details.

(Approximate Quantities)

Check oil and fluid levels with dipsticks or reservoir gauges.

Saloon

Wagon

Exterior light

1. UN-R stands for United Nations Regulation.

2. LED is the abbreviation for Light Emitting Diode.

Interior light

1. UN-R stands for United Nations Regulation.

2. LED is the abbreviation for Light Emitting Diode.

Tyre mark information

Choose the proper tyres for your vehicle using the following tyre mark information.

Tyre and inflation pressure

 

---

The tyres have been optimally matched with the chassis of your vehicle.

When replacing tyres, Mazda recommends that you replace tyres of the same type originally fitted to your vehicle. For details, contact an expert repairer, we recommend an Authorised Mazda Repairer.

Close Note

View Note

Check the tyre pressure label for tyre size and inflation pressure.

• Refer to Tyre Pressure Label (Search).

• Refer to Tyre Inflation Pressure (Search).

Standard tyre

1 person's weight: About 75 kg

1. European models

   • SKYACTIV-G 2.5

     (With Cylinder Deactivation)

     Before driving at high speeds, increase the pressure of the front tyres. For speeds above 210 km/h (131 mph), increase the pressure of the front tyres by 20 kPa (0.2 bar, 2.9 psi).

     (Without Cylinder Deactivation)

     Before driving at high speeds, increase the pressure of the front tyres. For speeds above 210 km/h (131 mph), increase the pressure of the front tyres by 10 kPa (0.1 bar, 1.5 psi).

   • SKYACTIV-G 2.5T

     Before driving at high speeds, increase the pressure of the front tyres. For speeds above 200 km/h (124 mph), increase the pressure of the front tyres by 30 kPa (0.3 bar, 4.4 psi).

   • SKYACTIV-D 2.2

     (Left-hand drive model)

     Before driving at high speeds, increase the pressure of the front tyres. For speeds above 190 km/h (118 mph), increase the pressure of the front tyres by 20 kPa (0.2 bar, 2.9 psi).

     (Right-hand drive model)

     Before driving at high speeds, increase the pressure of the front tyres. For speeds above 200 km/h (124 mph), increase the pressure of the front tyres by 20 kPa (0.2 bar, 2.9 psi).

   Except European models

   • SKYACTIV-G 2.5 (Left-hand drive model, Right-hand drive model (Saloon))

     Before driving at high speeds, increase the pressure of the front tyres. For speeds above 210 km/h (131 mph), increase the pressure of the front tyres by 10 kPa (0.1 bar, 1.5 psi).

   • SKYACTIV-G 2.5T

     Before driving at high speeds, increase the pressure of the front tyres. For speeds above 200 km/h (124 mph), increase the pressure of the front tyres by 20 kPa (0.2 bar, 2.9 psi).

   • SKYACTIV-D 2.2

     Before driving at high speeds, increase the pressure of the front tyres. For speeds above 190 km/h (118 mph), increase the pressure of the front tyres by 20 kPa (0.2 bar, 2.9 psi).

Temporary spare tyre (Some Models)

Winter tyre

1 person's weight: About 75 kg

1. Load index and Speed Symbol: 97Q/97S/97T/97H/97V

2. Load index and Speed Symbol: 92Q/92S/92T/92H/92V/92W

3. Load index and Speed Symbol: 97Q/97S/97T

4. Load index and Speed Symbol: 97H/97V

5. SKYACTIV-G 2.5 (With Cylinder Deactivation), SKYACTIV-D 2.2, Speed Symbol: 92S/92T

   Before driving at high speeds, increase the pressure of the front tyres. For speeds above 180 km/h (111 mph), increase the pressure of the front tyres by 10 kPa (0.1 bar, 1.5 psi).

   SKYACTIV-G 2.5 (With Cylinder Deactivation), SKYACTIV-D 2.2, Speed Symbol: 92H/92V

   Before driving at high speeds, increase the pressure of the front tyres. For speeds above 180 km/h (111 mph), increase the pressure of the front tyres by 20 kPa (0.2 bar, 2.9 psi).

   SKYACTIV-G 2.5, SKYACTIV-G 2.5T, SKYACTIV-D 2.2, Speed Symbol: 92W

   Before driving at high speeds, increase the pressure of the front tyres. For speeds above 180 km/h (111 mph), increase the pressure of the front tyres by 30 kPa (0.3 bar, 4.4 psi).

6. Load index and Speed Symbol: 92Q/92S/92T

7. Load index and Speed Symbol: 92H/92V/92W

Wheel nut tightening torque

When installing a tyre, tighten the wheel nut to the following torque.

108―147 N·m (12―14 kgf·m, 80―108 ft·lbf)

Refer to Fuses (Search).

If you require information regarding the wear limit specification for the brake disc plates and the measurement method, please contact an expert repairer, we recommend an Authorised Mazda Repairer. The information is made freely available.