Warning/Indicator Lights and Warning Sounds

If a Warning Light Turns On or Flashes

Message Indicated in Multi-information Display (Some Models)

Message Indicated on Display (Some Models)

Warning Sound is Activated

Signal	Warning	Action to be taken
Seat Belt Warning Light	The seat belt warning light turns on if the driver or passenger's seat is occupied and the seat belt is not fastened with the ignition switched ON. If the driver or passenger's seat belt is unfastened (only when the passenger seat is occupied) and the vehicle is driven at a speed faster than about 20 km/h (12 mph), the warning light flashes. After a short time, the warning light stops flashing, but remains illuminated. If a seat belt remains unfastened, the warning light flashes again for a given period of time. If the driver or passenger's seat belt is unfastened after the warning light turns on, and the vehicle speed exceeds 20 km/h (12 mph), the warning light flashes again. (With passenger occupant classification system) To allow the passenger occupant classification sensor to function properly, do not place and sit on an additional seat cushion on the passenger's seat. The sensor may not function properly because the additional seat cushion could cause sensor interference. (Without passenger occupant classification system) Placing heavy items on the passenger's seat may cause the passenger's seat belt warning function to operate depending on the weight of the item. To allow the passenger's seat weight sensor to function properly, do not place and sit on an additional seat cushion on the passenger's seat. The sensor may not function properly because the additional seat cushion could cause sensor interference. If a small child is seated on the passenger's seat, the warning light may not operate. Close Note View Note	Fasten the seat belts.
Door-Ajar/Boot lid-Ajar Warning Indication/Warning Light	The light turns on if any door/boot lid is not closed securely.	Close the door/boot lid securely.
Low Fuel Warning Light	The light turns on when the remaining fuel is about 9.0 L (2.3 US gal, 1.9 Imp gal). The light illumination timing may vary because fuel inside the fuel tank moves around according to the driving conditions and the vehicle posture. Close Note View Note	Add fuel.
120km/h Warning Light (Some Models)	The 120 km/h warning light illuminates when the vehicle speed exceeds 120 km/h.	Lower the vehicle speed.
Low Washer Fluid Level Warning Indication/Warning Light (Some Models)	This warning light indicates that little washer fluid remains.	Add washer fluid (Search).

Signal

Warning

Action to be taken

Seat Belt Warning Light

The seat belt warning light turns on if the driver or passenger's seat is occupied and the seat belt is not fastened with the ignition switched ON.

If the driver or passenger's seat belt is unfastened (only when the passenger seat is occupied) and the vehicle is driven at a speed faster than about 20 km/h (12 mph), the warning light flashes. After a short time, the warning light stops flashing, but remains illuminated. If a seat belt remains unfastened, the warning light flashes again for a given period of time.

If the driver or passenger's seat belt is unfastened after the warning light turns on, and the vehicle speed exceeds 20 km/h (12 mph), the warning light flashes again.
(With passenger occupant classification system)

To allow the passenger occupant classification sensor to function properly, do not place and sit on an additional seat cushion on the passenger's seat. The sensor may not function properly because the additional seat cushion could cause sensor interference.
(Without passenger occupant classification system)
- Placing heavy items on the passenger's seat may cause the passenger's seat belt warning function to operate depending on the weight of the item.
- To allow the passenger's seat weight sensor to function properly, do not place and sit on an additional seat cushion on the passenger's seat. The sensor may not function properly because the additional seat cushion could cause sensor interference.
If a small child is seated on the passenger's seat, the warning light may not operate.

Close Note

View Note

Fasten the seat belts.

Door-Ajar/Boot lid-Ajar Warning Indication/Warning Light

The light turns on if any door/boot lid is not closed securely.

Close the door/boot lid securely.

Low Fuel Warning Light

The light turns on when the remaining fuel is about 9.0 L (2.3 US gal, 1.9 Imp gal).

The light illumination timing may vary because fuel inside the fuel tank moves around according to the driving conditions and the vehicle posture.

Close Note

View Note

Add fuel.

120km/h Warning Light (Some Models)

The 120 km/h warning light illuminates when the vehicle speed exceeds 120 km/h.

Lower the vehicle speed.

Low Washer Fluid Level Warning Indication/Warning Light (Some Models)

This warning light indicates that little washer fluid remains.

Add washer fluid (Search).

Warning	Action to be taken
When the warning light illuminates, and the warning beep sound is heard when tyre pressure is too low in one or more tyres. If the tyre pressure monitoring system warning light illuminates or flashes, or the tyre pressure warning beep sound is heard, decrease vehicle speed immediately and avoid sudden manoeuvring and braking: If the tyre pressure monitoring system warning light illuminates or flashes, or the tyre pressure warning beep sound is heard, it is dangerous to drive the vehicle at high speeds, or perform sudden manoeuvring or braking. Vehicle drivability could worsen and result in an accident. To determine if you have a slow leak or a flat, pull over to a safe position where you can check the visual condition of the tyre and determine if you have enough air to proceed to a place where air may be added and the system monitored again by an expert repairer, we recommend an Authorised Mazda Repairer or a tyre repair station. Do not ignore the TPMS Warning Light: Ignoring the TPMS warning light is dangerous, even if you know why it is illuminated. Have the problem taken care of as soon as possible before it develops into a more serious situation that could lead to tyre failure and a dangerous accident. Close Warning View Warning	Inspect the tyres and adjust to the specified inflation pressure (Search). When replacing/repairing the tyres or wheels or both, have the work done by an Authorised Mazda Repairer, or the tyre pressure sensors may be damaged. Close Caution View Caution Perform tyre pressure adjustment when the tyres are cold. Tyre pressure will vary according to the tyre temperature, therefore let the vehicle stand for 1 hour or only drive it 1.6 km (1 mile) or less before adjusting the tyre pressures. When pressure is adjusted on hot tyres to the cold inflation pressure, the TPMS warning light/beep may turn on after the tyres cool and pressure drops below specification. Also, an illuminated TPMS warning light, resulting from the tyre air pressure dropping due to cold ambient temperature, may turn off if the ambient temperature rises. In this case, it will also be necessary to adjust the tyre air pressures. If the TPMS warning light illuminates due to a drop in tyre air pressure, make sure to check and adjust the tyre air pressures. After adjusting the tyre air pressures, it may require some time for the TPMS warning light to turn off. If the TPMS warning light remains illuminated, drive the vehicle at a speed of at least 25 km/h (16 mph) for 10 minutes, and then verify that it turns off. Tyres lose air naturally over time and the TPMS cannot tell if the tyres are getting too soft over time or you have a flat. However, when you find one low tyre in a set of four-that is an indication of trouble; you should have someone drive the vehicle slowly forward so you can inspect any low tyre for cuts and any metal objects sticking through tread or sidewall. Put a few drops of water in the valve stem to see if it bubbles indicating a bad valve. Leaks need to be addressed by more than simply refilling the trouble tyre as leaks are dangerous ― take it to an expert repairer, we recommend an Authorised Mazda Repairer which has all the equipment to fix tyres, TPMS systems and order the best replacement tyre for your vehicle. If the warning light illuminates again even after the tyre pressures are adjusted, there may be a tyre puncture. Refer to Vehicle with Run-flat Tyres (Search). Close Note View Note

Warning

Action to be taken

When the warning light illuminates, and the warning beep sound is heard when tyre pressure is too low in one or more tyres.

If the tyre pressure monitoring system warning light illuminates or flashes, or the tyre pressure warning beep sound is heard, decrease vehicle speed immediately and avoid sudden manoeuvring and braking:

If the tyre pressure monitoring system warning light illuminates or flashes, or the tyre pressure warning beep sound is heard, it is dangerous to drive the vehicle at high speeds, or perform sudden manoeuvring or braking. Vehicle drivability could worsen and result in an accident.

To determine if you have a slow leak or a flat, pull over to a safe position where you can check the visual condition of the tyre and determine if you have enough air to proceed to a place where air may be added and the system monitored again by an expert repairer, we recommend an Authorised Mazda Repairer or a tyre repair station.

Do not ignore the TPMS Warning Light:

Ignoring the TPMS warning light is dangerous, even if you know why it is illuminated. Have the problem taken care of as soon as possible before it develops into a more serious situation that could lead to tyre failure and a dangerous accident.

Close Warning

View Warning

Inspect the tyres and adjust to the specified inflation pressure (Search).

When replacing/repairing the tyres or wheels or both, have the work done by an Authorised Mazda Repairer, or the tyre pressure sensors may be damaged.

Close Caution

View Caution

Perform tyre pressure adjustment when the tyres are cold. Tyre pressure will vary according to the tyre temperature, therefore let the vehicle stand for 1 hour or only drive it 1.6 km (1 mile) or less before adjusting the tyre pressures. When pressure is adjusted on hot tyres to the cold inflation pressure, the TPMS warning light/beep may turn on after the tyres cool and pressure drops below specification.

Also, an illuminated TPMS warning light, resulting from the tyre air pressure dropping due to cold ambient temperature, may turn off if the ambient temperature rises. In this case, it will also be necessary to adjust the tyre air pressures. If the TPMS warning light illuminates due to a drop in tyre air pressure, make sure to check and adjust the tyre air pressures.
After adjusting the tyre air pressures, it may require some time for the TPMS warning light to turn off. If the TPMS warning light remains illuminated, drive the vehicle at a speed of at least 25 km/h (16 mph) for 10 minutes, and then verify that it turns off.
Tyres lose air naturally over time and the TPMS cannot tell if the tyres are getting too soft over time or you have a flat. However, when you find one low tyre in a set of four-that is an indication of trouble; you should have someone drive the vehicle slowly forward so you can inspect any low tyre for cuts and any metal objects sticking through tread or sidewall. Put a few drops of water in the valve stem to see if it bubbles indicating a bad valve. Leaks need to be addressed by more than simply refilling the trouble tyre as leaks are dangerous ― take it to an expert repairer, we recommend an Authorised Mazda Repairer which has all the equipment to fix tyres, TPMS systems and order the best replacement tyre for your vehicle.

If the warning light illuminates again even after the tyre pressures are adjusted, there may be a tyre puncture.

Refer to Vehicle with Run-flat Tyres (Search).

Close Note

View Note

Signal	Cause	Action to be taken
(White) KEY Indication (Some Models)	The advanced key battery is dead.	Replace the key battery (Search).
(Red) (Flashing) KEY Warning Light (Some Models)
(Red) (Flashing) KEY Warning Light (Some Models)	The advanced key is not within the operation range.	Bring the advanced key into the operation range (Search).
The advanced key is placed in areas inside the cabin where it is difficult for the key to be detected.
A key from another manufacturer similar to the advanced key is in the operation range.	Take the key from another manufacturer similar to the advanced key out of the operation range.
Without the ignition switched off, the advanced key is taken out of the cabin, and then all the doors are closed.	Bring the advanced key back into the cabin.

Signal

Cause

Action to be taken

(White)

KEY Indication (Some Models)

The advanced key battery is dead.

Replace the key battery (Search).

(Red)

(Flashing)

KEY Warning Light (Some Models)

(Red)

(Flashing)

KEY Warning Light (Some Models)

The advanced key is not within the operation range.

Bring the advanced key into the operation range (Search).

The advanced key is placed in areas inside the cabin where it is difficult for the key to be detected.

A key from another manufacturer similar to the advanced key is in the operation range.

Take the key from another manufacturer similar to the advanced key out of the operation range.

Without the ignition switched off, the advanced key is taken out of the cabin, and then all the doors are closed.

Bring the advanced key back into the cabin.

Warning/Indicator Lights and Warning Sounds

Taking Action