Audio Set [Type A (non-touchscreen)]

Switch the ignition to ACC or ON. Press the power/volume dial to turn the audio system on. Press the power/volume dial again to turn the audio system off.

To adjust the volume, turn the power/volume dial. Turn the power/volume dial clockwise to increase volume, anticlockwise to decrease it.

1. Press the menu button () to select the function. The selected function will be indicated.

2. Turn the audio control dial to adjust the selected functions as follows:

*1 With Radio Data System (RDS)

*2 Depending on the model, this function may not be available.

 

---

If not operated for several seconds, the display returns to the previous display. To reset bass, treble, fade, and balance, press the menu button () for 2 seconds. The unit will beep and “CLEAR” will be displayed.

Close Note

View Note

AF (Setting Alternative Frequency (AF)) (Some Models)

The AF function of the Radio Data System (RDS) can be set on or off.

Refer to Radio Data System (RDS) (Search).

REG (Setting Regional Programme (REG)) (Some Models)

The REG function of the Radio Data System (RDS) can be set on or off.

Refer to Radio Data System (RDS) (Search).

ALC (Automatic volume adjustment)

The automatic level control (ALC) changes the audio volume automatically according to the vehicle speed. The faster the vehicle speed, the higher the volume increases. ALC has ALC OFF and ALC LEVEL 1 to 7 modes. At ALC LEVEL 7, the amount that the volume can increase is at the maximum. Select the mode according to the driving conditions.

BEEP (Audio operation sound)

The setting for the operation sound when pressing and holding a button can be changed. The initial setting is ON. Set to OFF to mute the operation sound.

BT SETUP mode (Some Models)

Music and other audio such as voice data recorded on portable audio devices and mobile phones available on the market which are equipped with the Bluetooth^® transmission function can be listened to via wireless transmission over the vehicle's speakers. Using the BT SETUP mode, these devices can be programmed to the Bluetooth^® unit or changed (Search).

12HR 24HR (12 HR/24 HR time adjustment)

Rotating the audio control dial switches the display between 12 and 24-hour clock time (Search).

The clock can be set at any time when the ignition is switched to ACC or ON.

1. To adjust the time, press the clock button () for about 2 seconds until a beep is heard.

2. The clock's current time will flash.

   Time adjustment

   • To adjust the time, press the hour/minute set button (, ) while the clock's current time is flashing.

   • The hours advance while the hour set button () is pressed. The minutes advance while the minute set button () is pressed.

3. Press the clock button () again to start the clock.

1. Press the clock button () for about 2 seconds until a beep is heard.

2. Press the :00 button (1).

3. When the button is pressed, the time will be reset as follows:

   (Example)

   12:01―12:29→12:00

   12:30―12:59→1:00

 

---

• When the :00 button (1) is pressed, the seconds will start at “00”.

• Switching between 12 and 24-hour clock time:

  Press the menu button () several times until 12 and 24-hour clock time are displayed. Turn the audio control dial in either direction, select the desired clock setting while the preferred clock time is flashing.

Close Note

View Note

Press a band selector button () to turn the radio on.

Successively pressing the band selector button () switches the bands as follows: FM1→FM2→AM (Without Radio Data System (RDS)), MW/LW (With Radio Data System (RDS)).

The selected mode will be indicated.

 

---

If the FM broadcast signal becomes weak, reception automatically changes from STEREO to MONO for reduced noise.

Close Note

View Note

The radio has the following tuning methods: Manual, Seek, Scan, Preset channel, and Auto memory tuning. The easiest way to tune stations is to set them on preset channels.

Manual tuning

Select the station by pressing the tuning button (, ) lightly.

Seek tuning

Automatic search for radio stations starts when the tuning button (, ) is pressed until a beep sound is heard. The search stops when a station is found.

 

---

If you continue to press and hold the button, the frequency will continue changing without stopping.

Close Note

View Note

Scan tuning

Press and hold the scan button () to automatically sample strong stations. Scanning stops at each station for about 5 seconds. To hold a station, press and hold the scan button () again during this interval.

Preset channel tuning

The 6 preset channels can be used to store 6 AM (Without Radio Data System (RDS)), MW/LW (With Radio Data System (RDS)) and 12 FM stations.

1. To set a channel first select AM (Without Radio Data System (RDS)), MW/LW (With Radio Data System (RDS)), FM1, or FM2. Tune to the desired station.

2. Press a channel preset button for about 2 seconds until a beep is heard. The preset channel number or station frequency will be displayed. The station is now held in the memory.

3. Repeat this operation for the other stations and bands you want to store. To tune one in the memory, select AM (Without Radio Data System (RDS)), MW/LW (With Radio Data System (RDS)), FM1, or FM2 and then press its channel preset button. The station frequency or the channel number will be displayed.

Auto memory tuning (Without Radio Data System (RDS))

This is especially useful when driving in an area where the local stations are not known.

Press and hold the auto memory button () for about 2 seconds until a beep is heard; the system will automatically scan and temporarily store up to 6 stations with the strongest frequencies in each selected band in that area.

After scanning is completed, the station with the strongest frequency will be tuned and its frequency displayed. Press and release the auto memory button () to recall stations from the auto-stored stations. One stored station will be selected each time and its frequency and channel number will be displayed.

 

---

If no stations can be tuned after scanning operations, “A” will be displayed.

Close Note

View Note

 

---

The radio data system (RDS) does not function if it is out of the system's service coverage area.

Close Note

View Note

Alternative frequency (AF)

AF functions on FM stations. Press the menu button () and select the AF mode to turn it on and “AF” will be displayed. If the radio reception of the current station weakens, the system switches to an alternative station automatically.

If you wish to continue a regional programme, press the menu button () and select the REG mode to turn it on. “REG ON” is displayed. To cancel it, press the audio control dial and select the REG mode to turn it off. “REG OFF” is displayed.

Traffic announcement (TA)

If the traffic announcement button () is pressed, the unit switches to TA mode and “TA” is displayed.

If a TA broadcast is received while in the TA mode, the TA broadcast intercedes even while using other functions (FM, CD, USB device, AUX, or BT audio), and “Traffic Info” is displayed.

During a TA broadcast, press the traffic announcement button () to end the broadcast and return to the previous mode.

Programme-type information (PTY)

Some FM stations transmit programme-type codes. This code enables alternative stations transmitting the same programme-type code to be found quickly.

Press the programme-type information button (,) while in FM mode. The programme-type code and “PTY” will be displayed during reception. If there is no programme-type code, “None” will be displayed.

(To choose a programme-type:)

1. Press the Programme-type information button (,) when the programme-type code is displayed.

2. Operate any one of the following:

   • Press the pre-programmed channel preset button (1 to 6).

   • Press the Programme-type information button (,).

(To scan for programme-type information:)

1. Press the Programme-type information button (,) when the programme-type code is displayed.

2. Press the Programme-type information button (,) until the beep sounds.

   The unit will scan for broadcasts, if none are found, “Nothing” will be displayed and the unit will return to the previously tuned band.

(To store programme types in the channel preset buttons:)

1. Press the Programme-type information button (,) when the programme-type code is displayed.

2. Press the Programme-type information button (,) and select the programme type.

3. While the programme type is displayed, press a channel preset button for about 2 seconds.

Emergency broadcast

If an emergency broadcast is received, the emergency broadcast intercedes even while using other functions (FM, CD, USB device, AUX, or BT audio), and “Alarm!” is displayed.

When the emergency broadcast ends, the system will return to the previous mode.

1. Switch the ignition to ACC or ON.

2. Press the power/volume dial to turn the audio system on.

3. Press the media button () to switch to the USB mode and start playback.

 

---

• Some devices such as smart phones may require a setting change to allow operation using a USB connection.

• When the USB device is not connected, the mode does not switch to USB mode.

• When there is no playable data in the USB device, “NO CONTENTS” is flashed.

• Playback of the USB device is in the order of the folder numbers. Folders which have no MP3/WMA/AAC files are skipped.

• Do not remove the USB device while in the USB mode. The data may be damaged.

Close Note

View Note

Pause

To stop playback, press the play/pause button (4).

Press the button again to resume playback.

Fast-forward/Reverse

Press and hold the fast-forward button () to advance through a track at high speed.

Press and hold the reverse button () to reverse through a track at high speed.

Track search

Press the track up button () once to skip forward to the beginning of the next track.

Press the track down button () within a few seconds after playback begins to track down to the beginning of the previous track.

Press the track down button () after a few seconds have elapsed to start playback from the beginning of the current track.

Folder search

To change to the previous folder, press the folder down button (), or press the folder up button () to advance to the next folder.

Music scan

This function scans the titles in a folder currently being played and plays ten seconds of each song to aid you in finding a song you want to listen to.

Press and hold the scan button () during playback to start the scan play operation (the track number will flash). Press and hold the scan button () again to cancel scan playback.

 

---

If the unit is left in scan, normal playback will resume where scan was selected.

Close Note

View Note

Repeat playback

Track repeat

1. Press the repeat button (1) during playback to play the current track repeatedly. “TRACK RPT” is displayed ( is displayed next to RPT at the bottom of the display area).

2. To cancel the repeat playback, press the button again after 3 seconds.

Folder repeat

1. Press the repeat button (1) during playback, and then press the button again within 3 seconds to play the tracks in the current folder repeatedly. “FOLDER RPT” is displayed ( is displayed next to RPT at the bottom of the display area).

2. Press the button again to cancel the repeat playback.

Random playback

Tracks are randomly selected and played.

Folder random

1. Press the random button (2) during playback to play the tracks in the folder randomly. “FOLDER RDM” is displayed ( is displayed next to RDM at the bottom of the display area).

2. To cancel the random playback, press the button again after 3 seconds.

All random

1. Press the random button (2) during playback, and then press the button again within 3 seconds to play the tracks in the USB device randomly. “ALL RDM” is displayed ( is displayed next to RDM at the bottom of the display area).

2. Press the button again to cancel the random playback.

The information displayed on the audio display changes as follows each time the text button (3) is pressed during playback.

Button	Information displayed on audio display
	File number/Elapsed time
	Folder number/File number
	File name
	Folder name
	Album name
	Song name
	Artist name

 

---

• The information (artist name, music name) is displayed only when the USB device information in the USB device has information which can be displayed on the screen.

• This unit cannot display some characters. Characters which cannot be displayed are indicated by an asterisk ().

Close Note

View Note

Display scroll

Only 13 characters can be displayed at one time. To display the rest of the characters of a long title, press and hold the text button (3). The display scrolls the next 13 characters. Press and hold the text button (3) again after the last 13 characters have been displayed to return to the beginning of the title.

 

---

The number of characters which can be displayed is restricted.

Close Note

View Note

1. Switch the ignition to ACC or ON.

2. Press the power/volume dial to turn the audio system on.

3. Press the media button () to switch to the iPod mode and start playback.

 

---

• When an iPod is not connected, the mode does not switch to the iPod mode.

• When there is no playable data in the iPod, “NO CONTENTS” is flashed.

• Do not remove the iPod while in the iPod mode. Otherwise, the data could be damaged.

Close Note

View Note

Pause

To stop playback, press the play/pause button (4).

Press the button again to resume playback.

Fast-forward/Reverse

Press and hold the fast-forward button () to advance through a track at high speed.

Press and hold the reverse button () to reverse through a track at high speed.

Track search

Press the track up button () once to skip forward to the beginning of the next track.

Press the track down button () within a few seconds (depends on iPod software version) after playback begins to track down to the beginning of the previous track.

Press the track down button () after a few seconds (depends on iPod software version) have elapsed to start playback from the beginning of the current track.

Category search

Press the category down button (5) to select the previous category and press the category up button (6) to select the next category.

 

---

The types of categories include Playlist, Artist, Album, Song, Podcast, Genre, Composer, and Audio book.

Close Note

View Note

List search

Press the list down button () to select the previous list and press the list up button () to select the next list.

 

---

When the selected category is Song or Audio book, there is no list.

Close Note

View Note

Music scan

This function scans the titles in a list currently being played and plays 10 seconds of each song to aid you in finding a song you want to listen to.

Press and hold the scan button () during playback to start the scan play operation (the track number will flash). Press and hold the scan button () again to cancel scan playback.

 

---

If the unit is left in scan, normal playback will resume where scan was selected.

Close Note

View Note

Repeat playback

1. Press the repeat button (1) during playback to play the current track repeatedly. “TRACK RPT” is displayed ( is displayed next to RPT at the bottom of the display area).

2. Press the button again to cancel the repeat playback.

Random playback

Tracks are randomly selected and played.

Song random

1. Press the random button (2) during playback to play the tracks in the list randomly. “SONG RDM” is displayed ( is displayed next to RDM at the bottom of the display area).

2. To cancel the random playback, press the button again after 3 seconds.

Album random

1. Press the random button (2) during playback, and then press the button again within 3 seconds to play the tracks in the iPod randomly. “ALBUM RDM” is displayed ( is displayed next to RDM at the bottom of the display area).

2. Press the button again to cancel the random playback.

 

---

The track number being played randomly is in the order of the iPod shuffle table.

Close Note

View Note

The information displayed on the audio display changes as follows each time the text button (3) is pressed during playback.

Button	Information displayed on audio display
	File number/Elapsed time
	File number
	Category name
	Artist name
	Album name
	Song name

 

---

• The information (artist name, music name) is displayed only when the iPod has information which can be displayed.

• This unit cannot display some characters. Characters which cannot be displayed are indicated by an asterisk ().

Close Note

View Note

Display scroll

13 characters can be displayed at one time. To display the rest of the characters of a long title, press and hold the text button (3). The display scrolls the next 13 characters. Press and hold the text button (3) again after the last 13 characters have been displayed to return to the beginning of the title.

 

---

The number of characters which can be displayed is restricted.

Close Note

View Note