The speedometer indicates the speed of the vehicle.
In some countries, you may have to change the speed units between km/h and mph.
Press the speed unit selector for 1.5 seconds or more.
The speed units for the speedometer will change between km/h and mph.
The display mode can be changed from odometer to trip meter A to trip meter B and then back to odometer by pressing the selector while one of them is displayed. The selected mode will be displayed.
Type A/Type B
Type C
When the ignition is switched to ACC or off, the odometer or trip meters cannot be displayed, however, pressing the selector can inadvertently switch the trip meters or reset them during an approximate ten-minute period in the following cases:
After the ignition is switched to off from ON.
After the driver's door is opened.
Odometer
The odometer records the total distance the vehicle has been driven.
Trip meter
The trip meter can record the total distance of two trips. One is recorded in trip meter A, and the other is recorded in trip meter B.
For instance, trip meter A can record the distance from the point of origin, and trip meter B can record the distance from where the fuel tank is filled.
When trip meter A is selected, pressing the selector again within one second will change to trip meter B mode.
When trip meter A is selected, TRIP A will be displayed. When trip meter B is selected, TRIP B will be displayed.
The trip meter records the total distance the vehicle is driven until the meter is again reset. Return it to “0.0” by depressing and holding the selector for one second or more. Use this meter to measure trip distances and to compute fuel consumption.
(Vehicles with type C/type D audio)
If the fuel economy data is reset using the fuel economy monitor, or trip A is reset using the trip meter when the function which synchronizes the fuel economy monitor and the trip meter is on, the fuel economy data and trip A are reset simultaneously.
Refer to Fuel Economy Monitor (Search).
Only the trip meters record tenths of kilometres (miles).
The trip record will be erased when:
The power supply is interrupted (blown fuse or the battery is disconnected).
The vehicle is driven over 9999.9 km (mile).
The tachometer shows engine speed in thousands of revolutions per minute (rpm).
Do not run the engine with the tachometer needle in the RED ZONE.
This may cause severe engine damage.
Type A
Type B
When the tachometer needle enters the STRIPED ZONE, this indicates to the driver that the gears should be shifted before entering the RED ZONE.
The fuel gauge shows approximately how much fuel is remaining in the tank when the ignition is switched ON. We recommend keeping the tank over 1/4 full.
Type A
Type C
If the low fuel warning light illuminates or the fuel level is very low, refuel as soon as possible.
Refer to Warning Lights (Search).
After refuelling, it may require some time for the indicator to stabilize. In addition, the indicator may deviate while driving on a slope or curve since the fuel moves in the tank.
The display indicating a quarter or less remaining fuel has more segments to show the remaining fuel level in greater detail.
The direction of the arrow () indicates that the fuel-filler flap is on the left side of the vehicle.
(SKYACTIV-D 1.5, SKYACTIV-D 2.2)
If inconsistency in engine performance or stalling occurs due to low fuel level conditions, refuel the vehicle as soon as possible and add at least 10 L (2.7 US gal, 2.2 Imp gal) of fuel.
When the ignition is switched ON, the outside temperature is displayed.
Under the following conditions, the outside temperature display may differ from the actual outside temperature depending on the surroundings and vehicle conditions:
Significantly cold or hot temperatures.
Sudden changes in outside temperature.
The vehicle is parked.
The vehicle is driven at low speeds.
Changing the Temperature Unit of the Outside Temperature Display (Vehicles with Type C/D)
The outside temperature unit can be switched between Celsius and Fahrenheit.
Settings can be changed by operating the centre display screen.
Refer to Personalisation Features (Search).
When the temperature unit indicated in the outside temperature display is changed, the temperature unit indicated in the engine coolant gauge display changes in conjunction with it.
Outside Temperature Warning (Some Models)
When the outside temperature is low, the indication flashes and a beep sound is heard to warn the driver of the possibility of icy roads.
If the outside temperature is lower than about 4 °C (39 °F), the outside temperature display and the mark flashes for about ten seconds and a beep sound is heard once.
If the outside temperature is lower than -20 °C (-4 °F), the beep sound does not operate. However, the mark illuminates.
The vehicle speed preset using the cruise control is displayed.
The following information can be selected by pressing the INFO switch with the ignition switched ON.
Distance-to-empty mode
Average fuel economy mode
Current fuel economy mode
Average vehicle speed mode
Vehicle speed alarm mode (Some Models)
If you have any problems with your trip computer, consult an expert repairer, we recommend an Authorised Mazda Repairer.
Distance-to-empty mode
This mode displays the approximate distance you can travel on the remaining fuel based on the fuel economy.
The distance-to-empty will be calculated and displayed every second.
(European model)
(Except European model)
Even though the distance-to-empty display may indicate a sufficient amount of remaining driving distance before refuelling is required, refuel as soon as possible if the fuel level is very low or the low fuel warning light illuminates.
The display may not change unless you add more than approximately 9 L (2.3 US gal, 1.9 Imp gal) of fuel.
The distance-to-empty is the approximate remaining distance the vehicle can be driven until all the graduation marks in the fuel gauge (indicating the remaining fuel supply) disappear.
If there is no past fuel economy information such as after first purchasing your vehicle or the information is deleted when the battery leads are disconnected, the actual distance-to empty/range may differ from the amount indicated.
Average fuel economy mode
This mode displays the average fuel economy by calculating the total fuel consumption and the total travelled distance since purchasing the vehicle, re-connecting the battery after disconnection, or resetting the data. The average fuel economy is calculated and displayed every minute.
(European model)
(Except European model)
To clear the data being displayed, press the INFO switch for more than 1.5 seconds.
After pressing the INFO switch, - - - L/100 km (- - - mpg) will be displayed for about 1 minute before the fuel economy is recalculated and displayed.
Current fuel economy mode
This mode displays the current fuel economy by calculating the amount of fuel consumption and the distance travelled.
Current fuel economy will be calculated and displayed every 2 seconds.
(European model)
(Except European model)
When you've slowed to about 5 km/h (3 mph), - - - L/100 km (- - - mpg) will be displayed.
Average vehicle speed mode
This mode displays the average vehicle speed by calculating the distance and the time travelled since connecting the battery or resetting the data.
Average vehicle speed will be calculated and displayed every 10 seconds.
(European model)
(Except European model)
To clear the data being displayed, press the INFO button for more than 1.5 seconds. After pressing the INFO button, - - - km/h (- - - mph) will be displayed for about 1 minute before the vehicle speed is recalculated and displayed.
Vehicle speed alarm mode (Some Models)
In this mode, the current setting for the vehicle speed alarm is displayed. You can change the vehicle speed setting at which the warning is triggered.
The vehicle speed alarm display is activated at the same time the beep sound is heard. The set vehicle speed flashes several times.
The vehicle speed alarm can be set using the centre display.
Always set the vehicle speed according to the laws and regulations of the country/city in which the vehicle is driven. In addition, always verify the speed of the vehicle using the speedometer.
The vehicle speed alarm function can be set between 30 and 250 km/h (20 and 150 mph).
Always adjust the display brightness and position with the vehicle stopped:
Adjusting the display brightness and position while driving the vehicle is dangerous as doing so could distract your attention from the road ahead and lead to an accident.
Do not place beverages near the active driving display. If water or other liquids are splashed on the active driving display, it could cause damage.
Do not place objects above the active driving display or apply stickers to the dust-proof sheet/optical receiver as they will cause interference.
A sensor is integrated to control the display's luminosity. If the optical receiver is covered, the display's luminosity will lower making the display difficult to view.
Do not allow intense light to hit the optical receiver. Otherwise, it could cause damage.
It may be difficult to view the display when wearing polarized sunglasses. Take off your polarized sunglasses or adjust the luminosity.
If the battery has been removed and re-installed or the battery voltage is low, the adjusted position may deviate.
The display may be difficult to view or temporarily affected by weather conditions such as rain, snow, light, and temperature.
If the audio system is removed, the active driving display cannot be operated.
The active driving display indicates the following information:
Blind Spot Monitoring (BSM) Operation Conditions and Warnings
Refer to Blind Spot Monitoring (BSM) (Search).
Distance Recognition Support System (DRSS) Warnings
Refer to Distance Recognition Support System (DRSS) (Search).
Traffic Sign Recognition System (TSR) traffic signs and Warnings
Refer to Traffic Sign Recognition System (TSR) (Search).
Mazda Radar Cruise Control (MRCC) Operation Conditions and Warnings
Refer to Mazda Radar Cruise Control (MRCC) (Search).
Lane Departure Warning System (LDWS) Warnings
Refer to Lane Departure Warning System (LDWS) (Search).
Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) Operation Conditions and Warnings
Refer to Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) (Search).
Advanced Smart City Brake Support (Advanced SCBS) Warnings
Refer to Advanced Smart City Brake Support (Advanced SCBS) (Search).
Smart City Brake Support [Forward] (SCBS F) Warnings
Refer to Smart City Brake Support [Forward] (SCBS F) (Search).
Smart City Brake Support [Reverse] (SCBS R) Warnings
Refer to Smart City Brake Support [Reverse] (SCBS R) (Search).
Smart Brake Support (SBS) Warnings
Refer to Smart Brake Support (SBS) (Search).
Adjustable Speed Limiter Operation Conditions and Warnings
Refer to Adjustable Speed Limiter (Search).
Driver Attention Alert (DAA) Warnings
Refer to Driver Attention Alert (DAA) (Search).
Cruise Control Operation Conditions
Refer to Cruise Control (Search).
Navigation Guidance (vehicles with navigation system)
Speed limit indicator (vehicles with navigation system)
Vehicle Speed
Each setting/adjustment for the active driving display can be performed on the centre display.
Select the icon on the home screen and display the Settings screen.
Select the AD-Disp tab.
Select the desired item and perform the setting/adjustment.
Method for adjusting screen brightness (automatically/manually)
Screen brightness initial settings (automatic adjustment is selected)
Screen brightness adjustment (manual adjustment is selected)
Display position of active driving display (display height)
Active driving display angle adjustment (display angle correction)
The combination of street name display, lane guidance, and turn by turn (TBT) can be changed. (navigation guidance)
Active driving display ON/OFF (indication)
Reset settings (reset)
The street name may not be displayed depending on the market and region.