Air-Conditioning System
Operating Tips
-
Operate the air-conditioning system with the engine running.
-
To prevent the battery from being discharged, do not leave the fan control switch on for a long period of time with the ignition switched ON when the engine is not running.
-
The airflow amount may decrease slightly while the i-stop function is operating.
-
Clear all obstructions such as leaves, snow and ice from the bonnet and the air inlet in the cowl grille to improve the system efficiency.
-
Use the air-conditioning system to defog the windows and dehumidify the air.
-
The recirculate mode should be used when driving through tunnels or while in a traffic jam, or when you would like to shut off outside air for quick cooling of the interior.
-
Use the outside air position for ventilation or windscreen defrosting.
-
If the vehicle has been parked in direct sunlight during hot weather, open the windows to let warm air escape, then run the air-conditioning system.
-
Run the air conditioner about 10 minutes at least once a month to keep internal parts lubricated.
-
Have the air conditioner checked before the weather gets hot. Lack of refrigerant may make the air conditioner less efficient.
The refrigerant specifications are indicated on a label attached to the inside of the engine compartment. If the wrong type of refrigerant is used, it could result in a serious malfunction of the air conditioner. Consult a professional, government certified repairer for the inspection or repair because a special device is required for the air conditioner maintenance.
For details, consult an expert repairer, we recommend an Authorised Mazda Repairer.
Vent Operation (Front)
Adjusting the Vents
Directing airflow
To adjust the direction of airflow, move the adjustment knob.
-
When using the air conditioner under humid ambient temperature conditions, the system may blow fog from the vents. This is not a sign of trouble but a result of humid air being suddenly cooled.
-
The air vents can be fully opened and closed by operating the dial.
Side Vents
Centre Vents
Selecting the Airflow Mode
The location airflow exits the air vents and the airflow amount may change depending on the open or close status of the air vents.
Front Air Conditioner
Air-conditioning system information is displayed on the display.
Control Switches
AUTO switch
By pressing the AUTO switch the following functions will be automatically controlled in accordance with the selected set temperature:
-
Airflow temperature
-
Amount of airflow
-
Selection of airflow mode
-
Outside/Recirculated air selection
-
Air conditioner operation
-
A/C or A/C ECO selection
AUTO switch indicator light
-
When on, it indicates auto operation, and the system will function automatically.
-
If any of the following switches are operated while in auto control, the AUTO switch indicator turns off.
-
Mode selector switch
-
Fan control switch
-
Windscreen defroster switch
The functions for switches other than those operated continue to operate in auto control.
-
Power switch (Fan On/Off)
The air-conditioning system turns on or off by pressing the power switch.
Temperature control dial
This dial controls temperature. Turn it clockwise for hot and anticlockwise for cold.
Turn the temperature control dial to adjust the temperature between 15 °C (60 °F) and 29 °C (84 °F).
-
When the SYNC switch is on:
Turn the driver temperature control dial to control the temperature throughout the entire cabin.
-
When the SYNC switch is off:
Turn the driver or front passenger temperature control dial to independently control the temperature on each side of the cabin.
-
The air-conditioning system changes to the individual operation mode (SYNC switch indicator light turns off) by turning the front passenger temperature control dial even when the SYNC switch is on, which allows individual control of the set temperature for the driver and front passenger.
-
When you set the temperature to the lower or upper limit, “Lo” or “Hi” is displayed.
-
The temperature units for the temperature setting display can be changed in conjunction with the temperature units for the outside temperature display.
(Instrument cluster Type A)
Refer to Outside Temperature Display (Search).
(Instrument cluster Type B)
Refer to Outside Temperature Display (Search).
Fan control switch
The fan has 7 speeds. The selected speed will be displayed.
Mode selector switch
The desired airflow mode can be selected (Search).
-
With the airflow mode set to the
position and the temperature control dial set at a medium temperature, heated air is directed to the feet and air at a comparably lower temperature will flow through the central, left and right vents. -
To set the air vent to
, press the windscreen defroster switch. -
In the
position, the air conditioner is automatically turned on and the outside air position is automatically selected to defrost the windscreen.
A/C switch
Pressing the A/C switch while the AUTO switch is turned on will turn off the air conditioner (cooling/dehumidifying functions).
The on/off of the air conditioner switches each time the A/C switch is pressed.
Changes as follows each time the A/C switch is pressed.
A/C→A/C ECO→Stop
-
The air conditioner operates when the A/C switch is pressed while the air conditioner is turned off.
-
The A/C ECO function is designed to economize use of the air-conditioning system. “A/C ECO” is displayed to indicate that the air-conditioning system is operating at optimum control.
-
The air conditioner may not function when the outside temperature approaches 0 °C (32 °F).
Air intake selector
Outside or recirculated air positions can be selected. Press the switch to select outside/recirculated air positions.
Recirculated air position (indicator light turns on)
Outside air is shut off. Use this position when going through tunnels, driving in congested traffic (high engine exhaust areas) or when quick cooling is desired.
Outside air position (indicator light turns off)
Outside air is allowed to enter the cabin. Use this mode for ventilation or windscreen defrosting.
Do not recirculate the air in the cabin during cold or rainy weather:
Recirculating the air in the cabin during cold and rainy weather is dangerous as it will cause the windows to fog up. Your vision will be hampered, which could lead to a serious accident.
SYNC (Synchronized Temperature) switch
Use the SYNC switch to change the mode between the individual operation (driver and passenger) and interconnection (simultaneous) modes.
Interconnection mode (indicator light turns on)
The set temperature for the driver and front passenger is controlled simultaneously.
Individual operation mode (indicator light turns off)
The set temperature can be controlled individually for the driver and front passenger.
Windscreen defroster switch
Press the switch to defrost the windscreen and front door windows.
Refer to Windscreen Defrosting and Defogging (Search).
Rear window defogger switch
Press the rear window defogger switch to defrost the rear window.
Refer to Rear Window Defogger (Search).
Operation of Automatic Air Conditioner
Windscreen Defrosting and Defogging
Press the windscreen defroster switch.
In this position, the outside air position is automatically selected, and the air conditioner automatically turns on. The air conditioner will directly dehumidify the air to the front windscreen and side windows (Search).
Airflow amount will be increased.
Set the temperature control to the hot or warm position when defogging ( position):
Using the position with the temperature control set to the cold position is dangerous as it will cause the outside of the windscreen to fog up. Your vision will be hampered, which could lead to a serious accident.
Use the temperature control dial to increase the air flow temperature and defog the windscreen more quickly.
Sunlight/Interior temperature sensor
Sunlight sensor
Do not place objects on the sunlight sensor. Otherwise, the interior temperature may not adjust correctly.
Interior temperature sensor
Do not cover the interior temperature sensor. Otherwise, the interior temperature may not adjust correctly.
Vent Operation (Rear)
Adjusting the Vents
Directing airflow
You can direct air flow by moving the adjustment knob.
When using the air conditioner, mist may come out from the vents. This is not a sign of trouble but a result of humid air being suddenly cooled.
Selecting the Airflow Mode
Rear Air Conditioner
Air-conditioning system information is displayed on the display.
Control Switches
Rear switch
Press the rear switch to operate the rear air conditioner.
The indicator illuminates to indicate that the rear air conditioner is operating.
AUTO switch
By pressing the AUTO switch the following functions will be automatically controlled in accordance with the set temperature:
-
Airflow temperature
-
Amount of airflow
-
Selection of airflow mode
Power switch
The rear air-conditioning system turns on or off by pressing the power switch.
Temperature control switch
This switch controls temperature. Press 
for hot and 
for cold.
Turn the temperature control dial to adjust the temperature between 15 °C (60 °F) and 29 °C (84 °F).
When the temperature control switch is set to the maximum or minimum, “Hi” or “Lo” is indicated on the display.
Fan control switch
The fan has five speeds. The selected speed will be displayed.
Mode selector switch
The desired airflow mode can be selected. Refer to Selecting the Airflow Mode (Search).
Operation of Automatic Air Conditioner
Operation from front seats
-
Turn the front air conditioner on.
-
Press the rear switch. The rear air conditioner operates.
-
Selection of the airflow mode, airflow amount and temperature will be automatically controlled to the same temperature setting as the front air conditioner for the driver's side.
-
Set the control dial to the recommended temperature of 22 °C (72 °F), and then adjust it as desired.
-
If the AUTO switch is pressed while the front A/C switch is off, the rear air conditioner operates only to circulate air.
-
Setting the temperature to the maximum high or low will not provide the desired temperature at a faster rate.
-
When selecting heat, the system will restrict airflow until it has warmed to prevent cold air from blowing out of the vents.
-
When the rear air conditioner is controlled to the same temperature setting as the front air conditioner for the driver's side, “SYNC” is displayed on the rear screen.
-
When operating the fan switch of the front air conditioner while the rear air conditioner is operating automatically, the airflow amount of the rear air conditioner may change.
-
Operation from rear seats
-
Turn the front air conditioner on.
-
Press the AUTO switch. The selection of the airflow mode and airflow amount will be automatically controlled.
-
Use the temperature control switch to set the desired temperature.
-
Set the control dial to the recommended temperature of 22 °C (72 °F), and then adjust it as desired.
-
If the AUTO switch is pressed while the front A/C switch is off, the rear air conditioner operates only to circulate air.
-
Setting the temperature to the maximum high or low will not provide the desired temperature at a faster rate.
-
When selecting heat, the system will restrict airflow until it has warmed to prevent cold air from blowing out of the vents.
-
When the rear air conditioner is operated automatically, “AUTO” is displayed on the rear screen.
-
When the rear air conditioner is controlled to the same temperature setting as the front air conditioner for the driver's side, “SYNC” is displayed on the rear screen.
-
To turn off the system, press the Power switch.
